Abstract: In this study, several crossplots of the P-impedance
with the lithology logs (gamma ray, neutron porosity, deep resistivity,
water saturation and Vp/Vs curves) were made in three available
wells, which were drilled in central part of the Blue Nile basin in
depths varies from 1460m to 1600m. These crossplots were
successful to discriminate between sand and shale when using PImpedance
values, and between the wet sand and the pay sand when
using both P-impedance and Vp/Vs together. Also some impedance
sections were converted to porosity sections using linear formula to
characterize the reservoir in terms of porosity. The used crossplots
were created on log resolution, while the seismic resolution can
identify only the reservoir, unless a 3D seismic angle stacks were
available; then it would be easier to identify the pay sand with great
confidence; through high resolution seismic inversion and
geostatistical approach when using P-impedance and Vp/Vs volumes.
Abstract: A nanocrystalline thin film of ZnSe was successfully
electrodeposited on copper substrate using a non-aqueous solution
and subsequently annealed in air at 400°C. XRD analysis indicates
the polycrystalline deposit of (111) plane in both the cases. The
sharpness of the peak increases due to annealing of the film and
average grain size increases to 20 nm to 27nm. SEM photograph
indicate that grains are uniform and densely distributed over the
surface. Annealing increases the average grain size by 20%. The EDS
spectroscopy shows the ratio of Zn & Se is 1.1 in case of annealed
film. AFM analysis indicates the average roughness of the film
reduces from 181nm to 165nm due to annealing of the film. The
bandgap also decreases from 2.71eV to 2.62eV.
Abstract: The aim of this work is to build a model based on
tissue characterization that is able to discriminate pathological and
non-pathological regions from three-phasic CT images. With our
research and based on a feature selection in different phases, we are
trying to design a neural network system with an optimal neuron
number in a hidden layer. Our approach consists of three steps:
feature selection, feature reduction, and classification. For each
region of interest (ROI), 6 distinct sets of texture features are
extracted such as: first order histogram parameters, absolute gradient,
run-length matrix, co-occurrence matrix, autoregressive model, and
wavelet, for a total of 270 texture features. When analyzing more
phases, we show that the injection of liquid cause changes to the high
relevant features in each region. Our results demonstrate that for
detecting HCC tumor phase 3 is the best one in most of the features
that we apply to the classification algorithm. The percentage of
detection between pathology and healthy classes, according to our
method, relates to first order histogram parameters with accuracy of
85% in phase 1, 95% in phase 2, and 95% in phase 3.
Abstract: Non-linear FEM calculations are indispensable when
important technical information like operating performance of a
rubber component is desired. For example rubber bumpers built into
air-spring structures may undergo large deformations under load,
which in itself shows non-linear behavior. The changing contact
range between the parts and the incompressibility of the rubber
increases this non-linear behavior further. The material
characterization of an elastomeric component is also a demanding
engineering task.
The shape optimization problem of rubber parts led to the study of
FEM based calculation processes. This type of problems was posed
and investigated by several authors. In this paper the time demand of
certain calculation methods are studied and the possibilities of time
reduction is presented.
Abstract: Elastomeric dielectric material has recently become a
new alternative for actuator technology. The characteristics of
dielectric elastomers placed between two electrodes to withstand
large strain when electrodes are charged has attracted the attention of
many researcher to study this material for actuator technology. Thus,
in the past few years Danfoss Ventures A/S has established their own
dielectric electro-active polymer (DEAP), which was called
PolyPower.
The main objective of this work was to investigate the dynamic
characteristics for vibration control of a PolyPower actuator folded in
‘pull’ configuration. A range of experiments was carried out on the
folded actuator including passive (without electrical load) and active
(with electrical load) testing. For both categories static and dynamic
testing have been done to determine the behavior of folded DEAP
actuator.
Voltage-Strain experiments show that the DEAP folded actuator is
a non-linear system. It is also shown that the voltage supplied has no
effect on the natural frequency. Finally, varying AC voltage with
different amplitude and frequency shows the parameters that
influence the performance of DEAP folded actuator. As a result, the
actuator performance dominated by the frequency dependence of the
elastic response and was less influenced by dielectric properties.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: The present paper summarizes the analysis of the
request for consultation of information and data on industrial
emissions made publicly available on the web site of the Ministry of
Environment, Land and Sea on integrated pollution prevention and
control from large industrial installations, the so called “AIA Portal”.
As a matter of fact, a huge amount of information on national
industrial plants is already available on internet, although it is usually
proposed as textual documentation or images.
Thus, it is not possible to access all the relevant information
through interoperability systems and also to retrieval relevant
information for decision making purposes as well as rising of
awareness on environmental issue.
Moreover, since in Italy the number of institutional and private
subjects involved in the management of the public information on
industrial emissions is substantial, the access to the information is
provided on internet web sites according to different criteria; thus, at
present it is not structurally homogeneous and comparable.
To overcome the mentioned difficulties in the case of the
Coordinating Committee for the implementation of the Agreement
for the industrial area in Taranto and Statte, operating before the
IPPC permit granting procedures of the relevant installation located
in the area, a big effort was devoted to elaborate and to validate data
and information on characterization of soil, ground water aquifer and
coastal sea at disposal of different subjects to derive a global
perspective for decision making purposes. Thus, the present paper
also focuses on main outcomes matured during such experience.
Abstract: This study is concerned with the optimization of
fermentation parameters for the hyper production of mannanase from
Fusarium oxysporum SS-25 employing two step statistical strategy
and kinetic characterization of crude enzyme preparation. The
Plackett-Burman design used to screen out the important factors in
the culture medium revealed 20% (w/w) wheat bran, 2% (w/w) each
of potato peels, soyabean meal and malt extract, 1% tryptone, 0.14%
NH4SO4, 0.2% KH2PO4, 0.0002% ZnSO4, 0.0005% FeSO4, 0.01%
MnSO4, 0.012% SDS, 0.03% NH4Cl, 0.1% NaNO3 in brewer’s spent
grain based medium with 50% moisture content, inoculated with
2.8×107 spores and incubated at 30oC for 6 days to be the main
parameters influencing the enzyme production. Of these factors, four
variables including soyabean meal, FeSO4, MnSO4 and NaNO3 were
chosen to study the interactive effects and their optimum levels in
central composite design of response surface methodology with the
final mannanase yield of 193 IU/gds. The kinetic characterization
revealed the crude enzyme to be active over broader temperature and
pH range. This could result in 26.6% reduction in kappa number with
4.93% higher tear index and 1% increase in brightness when used to
treat the wheat straw based kraft pulp. The hydrolytic potential of
enzyme was also demonstrated on both locust bean gum and guar
gum.
Abstract: Water contamination by toxic compound is one of the serious environmental problems today. These toxic compounds mostly originated from industrial effluents, agriculture, natural sources and human waste. These studies focus on modification of multiwalled carbon nanotube (MWCNTs) with nanoparticle of calixarene and explore the possibility of using this modification for the remediation of cadmium in water. The nanocomposites were prepared by dissolving calixarene in chloroform solution as solvent, followed by additional multiwalled carbon nanotube (MWCNTs) then sonication process for 3 hour and fabricated the nanocomposites on substrate by spin coating method. Finally, the nanocomposites were tested on cadmium ion (10 mg/ml). The morphology of nanocomposites was investigated by FESEM showing the formation of calixarene on the outer walls of carbon nanotube and cadmium ion also clearly seen from the micrograph. This formation was supported by using energy dispersive x-ray (EDX). The presence of cadmium ions in the films, leads to some changes in the surface potential and Fourier Transform Infrared spectroscopy (FTIR).The nanocomposites MWCNTs-calixarene have potential for development of sensor for pollutant monitoring and nanoelectronics devices applications.
Abstract: Complexation of anthocyanins to mimic natural
copigmentation process was investigated. Cyanidin-rich extracts from
Zea mays L. ceritina Kulesh. and delphinidin-rich extracts from
Clitoria ternatea L. were used to form 4 anthocyanin complexes,
AC1, AC2, AC3 and AC4, in the presence of several polyphenols and
a trace metal. Characterizations of the ACs were conducted by UV,
FTIR, DSC/TGA and morphological observations. Bathochromic
shifts of the UV spectra of 4 formulas of ACs were observed at peak
wavelengths of about 510-620 nm by 10 nm suggesting complex
formation. FTIR spectra of the ACs indicate shifts of peaks from
1,733 cm-1 to 1,696 cm-1 indicating interactions and a decrease in the
peak areas within the wavenumber of 3,400-3,500 cm-1 indicating
changes in hydrogen bonding. Thermal analysis of all of the ACs
suggests increases in melting temperature after complexation. AC
with the highest melting temperature was morphologically observed
by SEM and TEM to be crystal-like particles within a range of 50 to
200 nm. Particle size analysis of the AC by laser diffraction gave a
range of 50-600 nm, indicating aggregation. This AC was shown to
have no cytotoxic effect on cultured HGEPp0.5 and HGF (all p>
0.05) by MTT. Therefore, complexation of anthocyanins was simple
and self-assembly process, potentially resulting in nanosized particles
of anthocyanin complex.
Abstract: Alkylated silicon nanocrystals (C11-SiNCs) were
prepared successfully by galvanostatic etching of p-Si(100) wafers
followed by a thermal hydrosilation reaction of 1-undecene in
refluxing toluene in order to extract C11-SiNCs from porous silicon.
Erbium trichloride was added to alkylated SiNCs using a simple
mixing chemical route. To the best of our knowledge, this is the first
investigation on mixing SiNCs with erbium ions (III) by this
chemical method. The chemical characterization of C11-SiNCs and
their mixtures with Er3+(Er/C11-SiNCs) were carried out using X-ray
photoemission spectroscopy (XPS). The optical properties of C11-
SiNCs and their mixtures with Er3+ were investigated using Raman
spectroscopy and photoluminescence (PL). The erbium mixed
alkylated SiNCs shows an orange PL emission peak at around 595
nm that originates from radiative recombination of Si. Er/C11-SiNCs
mixture also exhibits a weak PL emission peak at 1536 nm that
originates from the intra-4f transition in erbium ions (Er3+). The PL
peak of Si in Er/C11-SiNCs mixture is increased in the intensity up to
three times as compared to pure C11-SiNCs. The collected data
suggest that this chemical mixing route leads instead to a transfer of
energy from erbium ions to alkylated SiNCs.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: The paper involves a chain of activities from
synthesis, establishment of the methodology for characterization and
testing of novel protective materials through the pilot production and
application on model supports.
It summarizes the results regarding the development of the pilot
production protocol for newly developed self-cleaning materials. The
optimization of the production parameters was completed in order to
improve the most important functional properties (mineralogy
characteristics, particle size, self-cleaning properties and
photocatalytic activity) of the newly designed nanocomposite
material.
Abstract: We present an analytical model for the calculation of
the sensitivity, the spectral current noise and the detective parameter
for an optically illuminated In0.53Ga0.47As n+nn+ diode. The
photocurrent due to the excess carrier is obtained by solving the
continuity equation. Moreover, the current noise level is evaluated at
room temperature and under a constant voltage applied between the
diode terminals. The analytical calculation of the current noise in the
n+nn+ structure is developed by considering the free carries
fluctuations. The responsivity and the detection parameter are
discussed as functions of the doping concentrations and the emitter
layer thickness in one-dimensional homogeneous n+nn+ structure.
Abstract: Non-destructive testing and evaluation techniques for
assessing the integrity of composite structures are essential to both
reduce manufacturing costs and out of service time of transport means
due to maintenance. In this study, Analyze into non-destructive test
characterization of carbon fiber reinforced plastics (CFRP) internal
and external defects using thermo-graphic camera and transient
thermography method. non-destructive testing were characterized by
defect size (Ø8, Ø10, Ø12, Ø14) and depth (1.2mm, 2.4mm).
Abstract: In this study, microcrystalline cellulose (MCC) was
extracted from oil palm empty fruit bunch (EFB) cellulose which was
earlier isolated from oil palm EFB fibre. In order to isolate the
cellulose, the chlorination method was carried out. Then, the MCC
was prepared by simultaneous ultrasonic and alkali treatment from
the isolated α-cellulose. Based on mass balance calculation, the yields
for MCC obtained from EFB was 44%. For fiber characterization, it
is observed that the chemical composition of the hemicellulose and
lignin for all samples decreased while composition for cellulose
increased. The structural property of the MCC was studied by X-ray
diffraction (XRD) method and the result shows that the MCC
produced is a cellulose-I polymorph, with 73% crystallinity.
Abstract: This work is focused on the study of valuation of
recycled concrete aggregates, by measuring certain properties of
concrete in the fresh and hardened state. In this study, rheological
tests and physic-mechanical characterization on concretes and
mortars were conducted with recycled concrete whose geometric
properties were identified aggregates. Mortars were elaborated with
recycled fine aggregate (0/5mm) and concretes were manufactured
using recycled coarse aggregates (5/12.5 mm and 12.5/20 mm). First,
a study of the mortars was conducted to determine the effectiveness
of polycarboxylate superplasticizer on the workability of these and
their action deflocculating of the recycled sand. The rheological
behavior of mortars based on fine aggregate recycled was
characterized. The results confirm that the mortars composed of
different fractions of recycled sand (0 /5) have a better mechanical
properties (compressive and flexural strength) compared to normal
mortar. Also, the mechanical strengths of concretes made with
recycled aggregates (5/12.5 mm and 12.5/20 mm), are comparable to
those of conventional concrete with conventional aggregates,
provided that the implementation can be improved by the addition of
a superplasticizer.
Abstract: Calcium phosphate cement (CPC) is one of the most
attractive bioceramics due to its moldable and shape ability to fill
complicated bony cavities or small dental defect positions. In this
study, CPC was produced by using mixture of tetracalcium phosphate
(TTCP, Ca4O(PO4)2) and dicalcium phosphate anhydrous (DCPA,
CaHPO4) in equimolar ratio (1/1) with aqueous solutions of acetic
acid (C2H4O2) and disodium hydrogen phosphate dehydrate
(Na2HPO4.2H2O) in combination with sodium alginate in order to
improve theirs moldable characteristic. The concentration of the
aqueous solutions and sodium alginate were varied to investigate the
effect of different aqueous solutions and alginate on properties of the
cements. The cement paste was prepared by mixing cement powder
(P) with aqueous solution (L) in a P/L ratio of 1.0g/0.35ml. X-ray
diffraction (XRD) was used to analyses phase formation of the
cements. Setting time and compressive strength of the set CPCs were
measured using the Gilmore apparatus and Universal testing
machine, respectively.
The results showed that CPCs could be produced by using both
basic (Na2HPO4.2H2O) and acidic (C2H4O2) solutions. XRD results
show the precipitation of hydroxyapatite in all cement samples. No
change in phase formation among cements using difference
concentrations of Na2HPO4.2H2O solutions. With increasing
concentration of acidic solutions, samples obtained less
hydroxyapatite with a high dicalcium phosphate dehydrate leaded to
a shorter setting time. Samples with sodium alginate exhibited higher
crystallization of hydroxyapatite than that of without alginate as a
result of shorten setting time in a basic solution but a longer setting
time in an acidic solution. The stronger cement was attained from
samples using the acidic solution with sodium alginate; however the
strength was lower than that of using the basic solution.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Metallic foams have good potential for lightweight
structures for impact and blast mitigation. Therefore it is important to
find out the optimized foam structure (i.e. cell size, shape, relative
density, and distribution) to maximise energy absorption. In this
paper, quasistatic compression and microstructural characterization
of closed-cell aluminium foams of different pore size and cell
distributions have been carried out. We present results for two
different aluminium metal foams of density 0.49-0.51 g/cc and 0.31-
0.34 g/cc respectively that have been tested in quasi-static
compression. The influence of cell geometry and cell topology on
quasistatic compression behaviour has been investigated using optical
microscope and computed tomography (micro-CT) analysis. It is
shown that the deformation is not uniform in the structure and
collapse begins at the weakest point.