Abstract: This paper will discuss about an active power generator scheduling method in order to increase the limit level of steady state systems. Some power generator optimization methods such as Langrange, PLN (Indonesian electricity company) Operation, and the proposed Z-Thevenin-based method will be studied and compared in respect of their steady state aspects. A method proposed in this paper is built upon the thevenin equivalent impedance values between each load respected to each generator. The steady state stability index obtained with the REI DIMO method. This research will review the 500kV-Jawa-Bali interconnection system. The simulation results show that the proposed method has the highest limit level of steady state stability compared to other optimization techniques such as Lagrange, and PLN operation. Thus, the proposed method can be used to create the steady state stability limit of the system especially in the peak load condition.
Abstract: In this paper, a PSO-based approach is proposed to
derive a digital controller for redesigned digital systems having an interval plant based on resemblance of the extremal gain/phase
margins. By combining the interval plant and a controller as an interval system, extremal GM/PM associated with the loop transfer function
can be obtained. The design problem is then formulated as an optimization problem of an aggregated error function revealing the deviation on the extremal GM/PM between the redesigned digital
system and its continuous counterpart, and subsequently optimized by
a proposed PSO to obtain an optimal set of parameters for the digital controller. Computer simulations have shown that frequency
responses of the redesigned digital system having an interval plant bare a better resemblance to its continuous-time counter part by the incorporation of a PSO-derived digital controller in comparison to those obtained using existing open-loop discretization methods.
Abstract: This paper presents the idea of a rough controller with application to control the overhead traveling crane system. The structure of such a controller is based on a suggested concept of a fuzzy logic controller. A measure of fuzziness in rough sets is introduced. A comparison between fuzzy logic controller and rough controller has been demonstrated. The results of a simulation comparing the performance of both controllers are shown. From these results we infer that the performance of the proposed rough controller is satisfactory.
Abstract: Future space vehicles will require the use of non-toxic, cryogenic propellants, because of the performance advantages over the toxic hypergolic propellants and also because of the environmental and handling concerns. A prototypical capillary flow liquid acquisition device (LAD) for cryogenic propellants was fabricated with a mesh screen, covering a rectangular flow channel with a cylindrical outlet tube, and was tested with liquid oxygen (LOX). In order to better understand the performance in various gravity environments and orientations with different submersion depths of the LAD, a series of computational fluid dynamics (CFD) simulations of LOX flow through the LAD screen channel, including horizontally and vertically submersions of the LAD channel assembly at normal gravity environment was conducted. Gravity effects on the flow field in LAD channel are inspected and analyzed through comparing the simulations.
Abstract: In developing a text-to-speech system, it is well
known that the accuracy of information extracted from a text is
crucial to produce high quality synthesized speech. In this paper, a
new scheme for converting text into its equivalent phonetic spelling
is introduced and developed. This method is applicable to many
applications in text to speech converting systems and has many
advantages over other methods. The proposed method can also
complement the other methods with a purpose of improving their
performance. The proposed method is a probabilistic model and is
based on Smooth Ergodic Hidden Markov Model. This model can be
considered as an extension to HMM. The proposed method is applied
to Persian language and its accuracy in converting text to speech
phonetics is evaluated using simulations.
Abstract: The purpose of this work is measurement of the
system presampling MTF of a variable resolution x-ray (VRX) CT
scanner. In this paper, we used the parameters of an actual VRX CT
scanner for simulation and study of effect of different focal spot sizes
on system presampling MTF by Monte Carlo method (GATE
simulation software). Focal spot size of 0.6 mm limited the spatial
resolution of the system to 5.5 cy/mm at incident angles of below 17º
for cell#1. By focal spot size of 0.3 mm the spatial resolution
increased up to 11 cy/mm and the limiting effect of focal spot size
appeared at incident angles of below 9º. The focal spot size of 0.3
mm could improve the spatial resolution to some extent but because
of magnification non-uniformity, there is a 10 cy/mm difference
between spatial resolution of cell#1 and cell#256. The focal spot size
of 0.1 mm acted as an ideal point source for this system. The spatial
resolution increased to more than 35 cy/mm and at all incident angles
the spatial resolution was a function of incident angle. By the way
focal spot size of 0.1 mm minimized the effect of magnification nonuniformity.
Abstract: Position based routing protocols are the kinds of
routing protocols, which they use of nodes location information,
instead of links information to routing. In position based routing
protocols, it supposed that the packet source node has position
information of itself and it's neighbors and packet destination node.
Greedy is a very important position based routing protocol. In one of
it's kinds, named MFR (Most Forward Within Radius), source node
or packet forwarder node, sends packet to one of it's neighbors with
most forward progress towards destination node (closest neighbor to
destination). Using distance deciding metric in Greedy to forward
packet to a neighbor node, is not suitable for all conditions. If closest
neighbor to destination node, has high speed, in comparison with
source node or intermediate packet forwarder node speed or has very
low remained battery power, then packet loss probability is
increased. Proposed strategy uses combination of metrics distancevelocity
similarity-power, to deciding about giving the packet to
which neighbor. Simulation results show that the proposed strategy
has lower lost packets average than Greedy, so it has more reliability.
Abstract: In this paper, a new approach for design of a fully
differential second order current mode continuous-time sigma-delta
modulator is presented. For circuit implementation, square root
domain (SRD) translinear loop based on floating-gate MOS
transistors that operate in saturation region is employed. The
modulator features, low supply voltage, low power consumption
(8mW) and high dynamic range (55dB). Simulation results confirm
that this design is suitable for data converters.
Abstract: Attitude control of aerospace system with liquid containers may face to a problem associate with fuel sloshing. The sloshing phenomena can degrade the stability of control system and in the worst case, interaction between the attitude control system and fuel vibration leading to resonance. In this paper, a full process of nonlinear dynamic modeling of an aerospace launch vehicle with fuel sloshing is given. Then, a new control system based on model reference adaptive filter is proposed and its algorithm is extracted. This controller implemented on the main attitude control system. Finally, numerical simulation of nonlinear model and control system is carried out to examine the performance of the new controller. Results of simulations show that the inconvenient effects of the fuel sloshing by augmenting this control system are reduced and attitude control system performs, satisfactorily.
Abstract: The flow and heat transfer mechanism in convex
corrugated tubes have been investigated through numerical
simulations in this paper. Two kinds of tube types named as symmetric
corrugated tube (SCT) and asymmetric corrugated tube (ACT) are
modeled and studied numerically based on the RST model. The
predictive capability of RST model is examined in the corrugation wall
in order to check the reliability of RST model under the corrugation
wall condition. We propose a comparison between the RST modelling
the corrugation wall with existing direct numerical simulation of Maaß
C and Schumann U [14]. The numerical results pressure coefficient at
different profiles between RST and DNS are well matched. The
influences of large corrugation tough radii to heat transfer and flow
characteristic had been considered. Flow and heat transfer comparison
between SCT and ACT had been discussed. The numerical results
show that ACT exhibits higher overall heat transfer performance than
SCT.
Abstract: A methodology to design a nonlinear observer in a
bond graph approach is proposed. The class of nonlinear observer
with multivariable nonlinearities is considered. A junction structure
of the bond graph observer is proposed. The proposed methodology
to an electrical transformer and a DC motor including the nonlinear
saturation is applied. Nonlinear observers for the transformer and DC
motor based on multivariable circle criterion in the physical domain
are proposed. In order to show the saturation effects on the
transformer and DC motor, simulation results are obtained. Finally,
the paper describes that convergence of the estimates to the true
states is achieved.
Abstract: The modeling of inelastic behavior of plastic materials requires measurements providing information on material response to different multiaxial loading conditions. Different triaxiality conditions and values of Lode parameters have to be
covered for complex description of the material plastic behavior.
Samples geometries providing material plastic behavoiur over the range of interest are proposed with the use of FEM analysis. Round samples with 3 different notches and smooth surface are used
together with butterfly type of samples tested at angle ranging for 0 to
90°. Identification of ductile damage parameters is carried out on
the basis of obtained experimental data for austenitic stainless steel.
The obtained material plastic damage parameters are subsequently applied to FEM simulation of notched CT normally samples used for
fracture mechanics testing and results from the simulation are
compared with real tests.
Abstract: The energy consumption and delay in read/write
operation of conventional SRAM is investigated analytically as well
as by simulation. Explicit analytical expressions for the energy
consumption and delay in read and write operation as a function of
device parameters and supply voltage are derived. The expressions are
useful in predicting the effect of parameter changes on the energy
consumption and speed as well as in optimizing the design of
conventional SRAM. HSPICE simulation in standard 0.25μm CMOS
technology confirms precision of analytical expressions derived from
this paper.
Abstract: The objective of this research is to examine the shear thinning behaviour of mixing flow of non-Newtonian fluid like toothpaste in the dissolution container with rotating stirrer. The problem under investigation is related to the chemical industry. Mixing of fluid is performed in a cylindrical container with rotating stirrer, where stirrer is eccentrically placed on the lid of the container. For the simulation purpose the associated motion of the fluid is considered as revolving of the container, with stick stirrer. For numerical prediction, a time-stepping finite element algorithm in a cylindrical polar coordinate system is adopted based on semi-implicit Taylor-Galerkin/pressure-correction scheme. Numerical solutions are obtained for non-Newtonian fluids employing power law model. Variations with power law index have been analysed, with respect to the flow structure and pressure drop.
Abstract: Virtual Assembly (VA) is one of the key technologies
in advanced manufacturing field. It is a promising application of
virtual reality in design and manufacturing field. It has drawn much
interest from industries and research institutes in the last two decades.
This paper describes a process for integrating an interactive Virtual
Reality-based assembly simulation of a digital mockup with the
CAD/CAM infrastructure. The necessary hardware and software
preconditions for the process are explained so that it can easily be
adopted by non VR experts. The article outlines how assembly
simulation can improve the CAD/CAM procedures and structures;
how CAD model preparations have to be carried out and which
virtual environment requirements have to be fulfilled. The issue of
data transfer is also explained in the paper. The other challenges and
requirements like anti-aliasing and collision detection have also been
explained. Finally, a VA simulation has been carried out for a ball
valve assembly and a car door assembly with the help of Vizard
virtual reality toolkit in a semi-immersive environment and their
performance analysis has been done on different workstations to
evaluate the importance of graphical processing unit (GPU) in the
field of VA.
Abstract: We study the typical domain size and configuration
character of a randomly perturbed system exhibiting continuous
symmetry breaking. As a model system we use rod-like objects
within a cubic lattice interacting via a Lebwohl–Lasher-type
interaction. We describe their local direction with a headless unit
director field. An example of such systems represents nematic LC or
nanotubes. We further introduce impurities of concentration p, which
impose the random anisotropy field-type disorder to directors. We
study the domain-type pattern of molecules as a function of p,
anchoring strength w between a neighboring director and impurity,
temperature, history of samples. In simulations we quenched the
directors either from the random or homogeneous initial
configuration. Our results show that a history of system strongly
influences: i) the average domain coherence length; and ii) the range
of ordering in the system. In the random case the obtained order is
always short ranged (SR). On the contrary, in the homogeneous case,
SR is obtained only for strong enough anchoring and large enough
concentration p. In other cases, the ordering is either of quasi long
range (QLR) or of long range (LR). We further studied memory
effects for the random initial configuration. With increasing external
ordering field B either QLR or LR is realized.
Abstract: The flow field and the motion of the free surface in an
oscillating container are simulated numerically to assess the numerical
approach for studying two-phase flows under oscillating conditions.
Two numerical methods are compared: one is to model the oscillating
container directly using the moving grid of the ALE method, and the
other is to simulate the effect of container motion using the oscillating
body force acting on the fluid in the stationary container. The
two-phase flow field in the container is simulated using the level set
method in both cases. It is found that the calculated results by the body
force method coinsides with those by the moving grid method and the
sloshing behavior is predicted well by both the methods. Theoretical
back ground and limitation of the body force method are discussed,
and the effects of oscillation amplitude and frequency are shown.
Abstract: This paper presents an optimal design of linear phase
digital high pass finite impulse response (FIR) filter using Improved
Particle Swarm Optimization (IPSO). In the design process, the filter
length, pass band and stop band frequencies, feasible pass band and
stop band ripple sizes are specified. FIR filter design is a multi-modal
optimization problem. An iterative method is introduced to find the
optimal solution of FIR filter design problem. Evolutionary
algorithms like real code genetic algorithm (RGA), particle swarm
optimization (PSO), improved particle swarm optimization (IPSO)
have been used in this work for the design of linear phase high pass
FIR filter. IPSO is an improved PSO that proposes a new definition
for the velocity vector and swarm updating and hence the solution
quality is improved. A comparison of simulation results reveals the
optimization efficacy of the algorithm over the prevailing
optimization techniques for the solution of the multimodal, nondifferentiable,
highly non-linear, and constrained FIR filter design
problems.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: This research simulates one of the natural phenomena,
the ocean wave. Our goal is to be able to simulate the ocean wave at
real-time rate with the water surface interacting with objects. The
wave in this research is calm and smooth caused by the force of the
wind above the ocean surface. In order to make the simulation of the
wave real-time, the implementation of the GPU and the
multithreading techniques are used here. Based on the fact that the
new generation CPUs, for personal computers, have multi cores, they
are useful for the multithread. This technique utilizes more than one
core at a time. This simulation is programmed by C language with
OpenGL. To make the simulation of the wave look more realistic, we
applied an OpenGL technique called cube mapping (environmental
mapping) to make water surface reflective and more realistic.