Abstract: In this paper, the application of the Mode Matching
(MM) method in the case of photonic crystal waveguide
discontinuities is presented. The structure under consideration is
divided into a number of cells, which supports a number of guided
and evanescent modes. These modes can be calculated numerically
by an alternative formulation of the plane wave expansion method
for each frequency. A matrix equation is then formed relating the
modal amplitudes at the beginning and at the end of the structure.
The theory is highly efficient and accurate and can be applied to
study the transmission sensitivity of photonic crystal devices due to
fabrication tolerances. The accuracy of the MM method is compared
to the Finite Difference Frequency Domain (FDFD) and the Adjoint
Variable Method (AVM) and good agreement is observed.
Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: Recognizing human action from videos is an active
field of research in computer vision and pattern recognition. Human
activity recognition has many potential applications such as video
surveillance, human machine interaction, sport videos retrieval and
robot navigation. Actually, local descriptors and bag of visuals words
models achieve state-of-the-art performance for human action
recognition. The main challenge in features description is how to
represent efficiently the local motion information. Most of the
previous works focus on the extension of 2D local descriptors on 3D
ones to describe local information around every interest point. In this
paper, we propose a new spatio-temporal descriptor based on a spacetime
description of moving points. Our description is focused on an
Accordion representation of video which is well-suited to recognize
human action from 2D local descriptors without the need to 3D
extensions. We use the bag of words approach to represent videos.
We quantify 2D local descriptor describing both temporal and spatial
features with a good compromise between computational complexity
and action recognition rates. We have reached impressive results on
publicly available action data set
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: Iris pattern is an important biological feature of human body; it becomes very hot topic in both research and practical applications. In this paper, an algorithm is proposed for iris recognition and a simple, efficient and fast method is introduced to extract a set of discriminatory features using first order gradient operator applied on grayscale images. The gradient based features are robust, up to certain extents, against the variations may occur in contrast or brightness of iris image samples; the variations are mostly occur due lightening differences and camera changes. At first, the iris region is located, after that it is remapped to a rectangular area of size 360x60 pixels. Also, a new method is proposed for detecting eyelash and eyelid points; it depends on making image statistical analysis, to mark the eyelash and eyelid as a noise points. In order to cover the features localization (variation), the rectangular iris image is partitioned into N overlapped sub-images (blocks); then from each block a set of different average directional gradient densities values is calculated to be used as texture features vector. The applied gradient operators are taken along the horizontal, vertical and diagonal directions. The low order norms of gradient components were used to establish the feature vector. Euclidean distance based classifier was used as a matching metric for determining the degree of similarity between the features vector extracted from the tested iris image and template features vectors stored in the database. Experimental tests were performed using 2639 iris images from CASIA V4-Interival database, the attained recognition accuracy has reached up to 99.92%.
Abstract: Recently, genetic algorithms (GA) and particle swarm optimization (PSO) technique have attracted considerable attention among various modern heuristic optimization techniques. Since the two approaches are supposed to find a solution to a given objective function but employ different strategies and computational effort, it is appropriate to compare their performance. This paper presents the application and performance comparison of PSO and GA optimization techniques, for Thyristor Controlled Series Compensator (TCSC)-based controller design. The design objective is to enhance the power system stability. The design problem of the FACTS-based controller is formulated as an optimization problem and both the PSO and GA optimization techniques are employed to search for optimal controller parameters. The performance of both optimization techniques in terms of computational time and convergence rate is compared. Further, the optimized controllers are tested on a weakly connected power system subjected to different disturbances, and their performance is compared with the conventional power system stabilizer (CPSS). The eigenvalue analysis and non-linear simulation results are presented and compared to show the effectiveness of both the techniques in designing a TCSC-based controller, to enhance power system stability.
Abstract: A new multi-step comprehensive experience-based
learning program was developed and carried out so that the students
understood about what was the principle of the circuit function and
how the designed circuit was used in actual advanced applications.
Abstract: This paper introduces the foundations of Bayesian probability theory and Bayesian decision method. The main goal of Bayesian decision theory is to minimize the expected loss of a decision or minimize the expected risk. The purposes of this study are to review the decision process on the issue of flood occurrences and to suggest possible process for decision improvement. This study examines the problem structure of flood occurrences and theoretically explicates the decision-analytic approach based on Bayesian decision theory and application to flood occurrences in Environmental Engineering. In this study, we will discuss about the flood occurrences upon an annual maximum water level in cm, 43-year record available from 1965 to 2007 at the gauging station of Sagaing on the Ayeyarwady River with the drainage area - 120193 sq km by using Bayesian decision method. As a result, we will discuss the loss and risk of vast areas of agricultural land whether which will be inundated or not in the coming year based on the two standard maximum water levels during 43 years. And also we forecast about that lands will be safe from flood water during the next 10 years.
Abstract: This paper presents a new growing neural network for
cluster analysis and market segmentation, which optimizes the size
and structure of clusters by iteratively checking them for multivariate
normality. We combine the recently published SGNN approach [8]
with the basic principle underlying the Gaussian-means algorithm
[13] and the Mardia test for multivariate normality [18, 19]. The new
approach distinguishes from existing ones by its holistic design and
its great autonomy regarding the clustering process as a whole. Its
performance is demonstrated by means of synthetic 2D data and by
real lifestyle survey data usable for market segmentation.
Abstract: Industrial robots become useless without end-effectors
that for many instances are in the form of friction grippers.
Commonly friction grippers apply frictional forces to different
objects on the basis of programmers- experiences. This puts a
limitation on the effectiveness of gripping force that may result in
damaging the object. This paper describes various stages of design
and development of a low cost sensor-based robotic gripper that
would facilitate the task of applying right gripping forces to different
objects. The gripper is also equipped with range sensors in order to
avoid collisions of the gripper with objects. It is a fully functional
automated pick and place gripper which can be used in many
industrial applications. Yet it can also be altered or further developed
in order to suit a larger number of industrial activities. The current
design of gripper could lead to designing completely automated robot
grippers able to improve the efficiency and productivity of industrial
robots.
Abstract: Nowadays, precipitation prediction is required for proper planning and management of water resources. Prediction with neural network models has received increasing interest in various research and application domains. However, it is difficult to determine the best neural network architecture for prediction since it is not immediately obvious how many input or hidden nodes are used in the model. In this paper, neural network model is used as a forecasting tool. The major aim is to evaluate a suitable neural network model for monthly precipitation mapping of Myanmar. Using 3-layerd neural network models, 100 cases are tested by changing the number of input and hidden nodes from 1 to 10 nodes, respectively, and only one outputnode used. The optimum model with the suitable number of nodes is selected in accordance with the minimum forecast error. In measuring network performance using Root Mean Square Error (RMSE), experimental results significantly show that 3 inputs-10 hiddens-1 output architecture model gives the best prediction result for monthly precipitation in Myanmar.
Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: There has been a growing interest in implementing humanoid avatars in networked virtual environment. However, most existing avatar communication systems do not take avatars- social backgrounds into consideration. This paper proposes a novel humanoid avatar animation system to represent personalities and facial emotions of avatars based on culture, profession, mood, age, taste, and so forth. We extract semantic keywords from the input text through natural language processing, and then the animations of personalized avatars are retrieved and displayed according to the order of the keywords. Our primary work is focused on giving avatars runtime instruction from multiple natural languages. Experiments with Chinese, Japanese and English input based on the prototype show that interactive avatar animations can be displayed in real time and be made available online. This system provides a more natural and interesting means of human communication, and therefore is expected to be used for cross-cultural communication, multiuser online games, and other entertainment applications.
Abstract: The 4G front-end transceiver needs a high
performance which can be obtained mainly with an optimal
architecture and a multi-band Local Oscillator. In this study, we
proposed and presented a new architecture of multi-band frequency
synthesizer based on an Inverse Sine Phase Detector Phase Locked
Loop (ISPD PLL) without any filters and any controlled gain block
and associated with adapted multi band LC tuned VCO using a
several numeric controlled capacitive branches but not binary
weighted. The proposed architecture, based on 0.35μm CMOS
process technology, supporting Multi-band GSM/DCS/DECT/
UMTS/WiMax application and gives a good performances: a phase
noise @1MHz -127dBc and a Factor Of Merit (FOM) @ 1MHz -
186dB and a wide band frequency range (from 0.83GHz to 3.5GHz),
that make the proposed architecture amenable for monolithic
integration and 4G multi-band application.
Abstract: Magnetic carbon nanotubes composites were obtained
by filling carbon nanotubes with paramagnetic iron oxide particles.
Detailed investigation of magnetic behaviour of resulting composites
was done at different temperatures. Measurements indicate that these
functionalized nanotubes are superparamagnetic at room temperature;
however, no superparamagnetism was observed at 125 K and 80 K.
The blocking temperature TB was estimated at 145 K. These magnetic
carbon nanotubes have the potential of being used in a wide range of
applications, in particular, the production of nanofluids, which can be
controlled and steered by appropriate magnetic fields.
Abstract: This research study examines cases of Saudi Arabian
universities and female academics for work environment issues
within the context of design management applications. The study
proposes use of design research, ergonomics and systems design
thinking to develop the university design which facilitates removal of
physical and cognitive barriers for female academics. Review of
literature demonstrates that macro and micro ergonomic combined
with design management and system design strategies can
significantly improve the workplace design for female academics.
The university design model would be prepared based on the analyses
of primary data obtained from archived documents, participants'
observation logs, photo audits, focus groups and semi-structured
interviews of currently employed female academics in the selected
case universities.
Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: This paper presents an economic game for sybil
detection in a distributed computing environment. Cost parameters
reflecting impacts of different sybil attacks are introduced in the sybil
detection game. The optimal strategies for this game in which both
sybil and non-sybil identities are expected to participate are devised.
A cost sharing economic mechanism called Discriminatory
Rewarding Mechanism for Sybil Detection is proposed based on this
game. A detective accepts a security deposit from each active agent,
negotiates with the agents and offers rewards to the sybils if the latter
disclose their identity. The basic objective of the detective is to
determine the optimum reward amount for each sybil which will
encourage the maximum possible number of sybils to reveal
themselves. Maintaining privacy is an important issue for the
mechanism since the participants involved in the negotiation are
generally reluctant to share their private information. The mechanism
has been applied to Tor by introducing a reputation scoring function.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: This paper describes the design concepts and
implementation of a 5-Joint mechanical arm for a rescue robot named
CEO Mission II. The multi-joint arm is a five degree of freedom
mechanical arm with a four bar linkage, which can be stretched to
125 cm. long. It is controlled by a teleoperator via the user-friendly
control and monitoring GUI program. With Inverse Kinematics
principle, we developed the method to control the servo angles of all
arm joints to get the desired tip position. By clicking the determined
tip position or dragging the tip of the mechanical arm on the
computer screen to the desired target point, the robot will compute
and move its multi-joint arm to the pose as seen on the GUI screen.
The angles of each joint are calculated and sent to all joint servos
simultaneously in order to move the mechanical arm to the desired
pose at once. The operator can also use a joystick to control the
movement of this mechanical arm and the locomotion of the robot.
Many sensors are installed at the tip of this mechanical arm for
surveillance from the high level and getting the vital signs of victims
easier and faster in the urban search and rescue tasks. It works very
effectively and easy to control. This mechanical arm and its software
were developed as a part of the CEO Mission II Rescue Robot that
won the First Runner Up award and the Best Technique award from
the Thailand Rescue Robot Championship 2006. It is a low cost,
simple, but functioning 5-Jiont mechanical arm which is built from
scratch, and controlled via wireless LAN 802.11b/g. This 5-Jiont
mechanical arm hardware concept and its software can also be used
as the basic mechatronics to many real applications.