Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.
Abstract: Wastages such as grated coconut meat, spent tea and used sugarcane had contributed negative impacts to the environment. Vermicomposting method is fully utilized to manage the wastes towards a more sustainable approach. The worms that are used in the vermicomposting are Eisenia foetida and Eudrillus euginae. This research shows that the vermicompost of wastages has voltage of electrical energy and is able to light up the Light-Emitting Diode (LED) device. Based on the experiment, the use of replicated and double compartments of the component will produce double of voltage. Hence, for conclusion, this harmless and low cost technology of vermicompost can act as a dry cell in order to reduce the usage of hazardous chemicals that can contaminate the environment.
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Abstract: High precision in motion is required to manipulate the
micro objects in precision industries for micro assembly, cell
manipulation etc. Precision manipulation is achieved based on the
appropriate mechanism design of micro devices such as
microgrippers. Design of a compliant based mechanism is the better
option to achieve a highly precised and controlled motion. This
research article highlights the method of designing a compliant based
three fingered microgripper suitable for holding asymmetric objects.
Topological optimization technique, a systematic method is
implemented in this research work to arrive a topologically optimized
design of the mechanism needed to perform the required micro
motion of the gripper. Optimization technique has a drawback of
generating senseless regions such as node to node connectivity and
staircase effect at the boundaries. Hence, it is required to have post
processing of the design to make it manufacturable. To reduce the
effect of post processing stage and to preserve the edges of the image,
a cubic spline interpolation technique is introduced in the MATLAB
program. Structural performance of the topologically developed
mechanism design is tested using finite element method (FEM)
software. Further the microgripper structure is examined to find its
fatigue life and vibration characteristics.
Abstract: Primary and secondary data from the Bauchi abattoir were utilized to determine the relative contributions of different livestock species to meat supply in Bauchi Metropolis. Daily livestock slaughter figures for five months (June – October 2011) indicated that more goats (64.0) were slaughtered than either sheep (47.3) or cattle (41.30) each day (P
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: The recycling of concrete, bricks and masonry rubble
as concrete aggregates is an important way to contribute to a
sustainable material flow. However, there are still various
uncertainties limiting the widespread use of Recycled Concrete
Aggregates (RCA). The fluctuations in the composition of grade
recycled aggregates and their influence on the properties of fresh and
hardened concrete are of particular concern regarding the use of
RCA. Most of problems occurring while using recycled concrete
aggregates as aggregates are due to higher porosity and hence higher
water absorption, lower mechanical strengths, residual impurities on
the surface of the RCA forming weaker bond between cement paste
and aggregate. So, the reuse of RCA is still limited. Efficient
polymer based treatment is proposed in order to reuse RCA easier.
The silicon-based polymer treatments of RCA were carried out and
were compared. This kind of treatment can improve the properties of
RCA such as the rate of water absorption on treated RCA is
significantly reduced.
Abstract: This work presents a neural network model for the
clustering analysis of data based on Self Organizing Maps (SOM).
The model evolves during the training stage towards a hierarchical
structure according to the input requirements. The hierarchical structure
symbolizes a specialization tool that provides refinements of the
classification process. The structure behaves like a single map with
different resolutions depending on the region to analyze. The benefits
and performance of the algorithm are discussed in application to the
Iris dataset, a classical example for pattern recognition.
Abstract: Monoculture and mixed cultures of microalgae and
the oleaginous yeast for microbial oil productions were investigated
using sugarcane juice as carbon substrate. The monoculture of yeast
Torulaspora maleeae Y30, Torulaspora globosa YU5/2 grew faster
than that of microalgae Chlorella sp. KKU-S2. In monoculture of T.
maleeae Y30, a biomass of 8.267g/L with lipid yield of 0.920g/L
were obtained, while 8.333g/L of biomass with lipid yield of
1.141g/L were obtained for monoculture of T. globosa YU5/2. A
biomass of 1.933g/L with lipid yield of 0.052g/L was found for
monoculture of Chlorella sp. KKU-S2. The biomass concentration in
the mixed culture of the oleaginous yeast with microalgae increased
faster and was higher compared with that in the monocultures. A
biomass of 8.733g/L with lipid yield of 1.564g/L was obtained for a
mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, while
8.010g/L of biomass with lipid yield of 2.424g/L was found for
mixed culture of T. globosa YU5/2 with Chlorella sp. KKU-S2.
Maximum cell yield coefficient (YX/S, g/L) was found of 0.323 in
monoculture of Chlorella sp. KKU-S2 but low level of both specific
yield of lipid (YP/X, g lipid/g cells) of 0.027 and volumetric lipid
production rate (QP, g/L/d) of 0.003 were observed. While, maximum
YP/X (0.303), QP (0.105) and maximum process product yield (YP/S,
0.061) were obtained in mixed culture of T. globosa YU5/2 with
Chlorella sp. KKU-S2. The results obtained from the study shows
that mixed culture of yeast with microalgae is a desirable cultivation
process for microbial oil production.
Abstract: In this study Vitaton (an organic supplement which
contains fermentative β-carotene) and synthetic astaxanthin
(CAROPHYLL® Pink) were evaluated as pro-growth factors in
Rainbow trout diet. An 8 week feeding trial was conducted to
determine the effects of Vitaton versus astaxanthin on rearing factors,
survival rate and visual flesh color of Rainbow trout
(Oncorhnchynchus mykiss) with initial weight of 196±5. Four
practical diets were formulated to contain 50 and 80 (ppm) of β-
carotene and astaxanthin and also a control diet was prepared without
any pigment. Each diet was fed to triplicate groups of fish rearing in
fresh water. Fish were fed twice daily. The water temperature
fluctuated from 12 to 15 (C˚) and also dissolved oxygen content was
between 7 to 7.5 (mg/lit) during the experimental period. At the end
of the experiment, growth and food utilization parameters and
survival rate were unaffected by dietary treatments (p>0.05). Also,
there was no significant difference between carcass yield within
treatments (p>0.05). No significant difference recognized between
visual flesh color (SalmoFan score) of fish fed Vitaton-containing
diets. On the contrary, feeding on diets containing 50 and 80 (ppm)
of astaxanthin, increased SalmoFan score (flesh astaxanthin
concentration) from
Abstract: Historic religious buildings located in seismic areas
have developed different failure mechanisms. Simulation of failure
modes is done with computer programs through a nonlinear dynamic
analysis or simplified using the method of failure blocks. Currently
there are simulation methodologies of failure modes based on the
failure rigid blocks method only for Roman Catholic churches type.
Due to differences of shape in plan, elevation and construction
systems between Orthodox churches and Catholic churches, for the
first time there were initiated researches in the development of this
simulation methodology for Orthodox churches. In this article are
presented the first results from the researches. The theoretical results
were compared with real failure modes recorded at an Orthodox
church from Banat region, severely damaged by earthquakes in
1991. Simulated seismic response, using a computer program based
on finite element method was confirmed by cracks after earthquakes.
The consolidation of the church was made according to these
theoretical results, realizing a rigid floor connecting all the failure
blocks.
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Abstract: Compared to oil production from microorganisms, little work has been performed for mixed culture of microalgae and yeast. In this article it is aimed to show high oil accumulation potential of mixed culture of microalgae Chlorella sp. KKU-S2 and oleaginous yeast Torulaspora maleeae Y30 using sugarcane molasses as substrate. The monoculture of T. maleeae Y30 grew faster than that of microalgae Chlorella sp. KKU-S2. In monoculture of yeast, a biomass of 6.4g/L with specific growth rate (m) of 0.265 (1/d) and lipid yield of 0.466g/L were obtained, while 2.53g/L of biomass with m of 0.133 (1/d) and lipid yield of 0.132g/L were obtained for monoculture of Chlorella sp. KKU-S2. The biomass concentration in the mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2 increased faster and was higher compared with that in the monoculture and mixed culture of microalgae. In mixed culture of microalgae Chlorella sp. KKU-S2 and C. vulgaris TISTR8580, a biomass of 3.47g/L and lipid yield of 0.123 g/L were obtained. In mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, a maximum biomass of 7.33 g/L and lipid yield of 0.808g/L were obtained. Maximum cell yield coefficient (YX/S, 0.229g/L), specific yield of lipid (YP/X, 0.11g lipid/g cells) and volumetric lipid production rate (QP, 0.115 g/L/d) were obtained in mixed culture of yeast and microalgae. Clearly, T. maleeae Y30 and Chlorella sp. KKU-S2 use sugarcane molasses as organic nutrients efficiently in mixed culture under mixotrophic growth. The biomass productivity and lipid yield are notably enhanced in comparison with monoculture.
Abstract: Following the research in the Department of environmental engineering in Faculty of mechanical engineering on Technical University of Kosice and experiences with electrocoagulation style of disposal waste water, there were designed and partly examining the equipment of two stage revitalization on the standing and little fusible water of tenet electrolysis on the little tarns. With the cooperation with vet experts was that manners prove and it is innocuous for animals, during which time cyanobacteria are totally paralyzed. For the implementation of science and research results have been obtained by means EU funds for structural development.
Abstract: This paper reports on the influence of surface-treated coarse recycled concrete aggregate (RCA) on developing the compressive strength of concrete. The coarse RCA was initially treated by separately impregnating it in calcium metasilicate (CM) or wollastonite and nanosilica (NS) prepared at various concentrations. The effects of both treatment materials on concrete properties (e.g., slump, density and compressive strength) were evaluated. Scanning electron microscopy (SEM) analysis was performed to examine the microstructure of the resulting concrete. Results show that the effective use of treated coarse RCA significantly enhances the compressive strength of concrete. This result is supported by the SEM analysis, which indicates the formation of a dense interface between the treated coarse RCA and the cement matrix. Coarse RCA impregnated in CM solution results in better concrete strength than NS, and the optimum concentration of CM solution recommended for treated coarse RCA is 10%.
Abstract: This research study the application of the immobilized
TiO2 layer and Cu-TiO2 layer on graphite substrate as a negative
electrode or anode for Li-ion battery. The titania layer was produced
through chemical bath deposition method, meanwhile Cu particles
were deposited electrochemically. A material can be used as an
electrode as it has capability to intercalates Li ions into its crystal
structure. The Li intercalation into TiO2/Graphite and Cu-
TiO2/Graphite were analyzed from the changes of its XRD pattern
after it was used as electrode during discharging process. The XRD
patterns were refined by Le Bail method in order to determine the
crystal structure of the prepared materials. A specific capacity and the
cycle ability measurement were carried out to study the performance
of the prepared materials as negative electrode of the Li-ion battery.
The specific capacity was measured during discharging process from
fully charged until the cut off voltage. A 300 was used as a load.
The result shows that the specific capacity of Li-ion battery with
TiO2/Graphite as negative electrode is 230.87 ± 1.70mAh.g-1 which is
higher than the specific capacity of Li-ion battery with pure graphite
as negative electrode, i.e 140.75 ±0.46mAh.g-1. Meanwhile
deposition of Cu onto TiO2 layer does not increase the specific
capacity, and the value even lower than the battery with
TiO2/Graphite as electrode. The cycle ability of the prepared battery
is only two cycles, due to the Li ribbon which was used as cathode
became fragile and easily broken.
Abstract: An experiment was conducted to determine the effect
of the rearing system on growth performance, carcass yield,
hematological parameters, and feather pecking damage of Thai
indigenous chickens. Three hundred and sixty 1-d-old chicks were
randomly assigned to 2 treatments: indoor treatment and outdoor
access treatment. In the indoor treatment, the chickens were housed
in floor pens (5 birds/m2). In the outdoor access treatment, the
chickens were housed in a similar indoor house; in addition, they also
had an outdoor grass paddock (1 bird/m2). All birds were provided
with same diet and were raised for 16 wk of age. The results showed
that growth performance and carcass yield were not different among
treatment (P>0.05). Outdoor access had no effect on hematological
parameters (P>0.05). However, the feather pecking damage of the
chickens in the outdoor access treatment was lower than that of the
chickens in the indoor treatment (P
Abstract: Shrunken patterning for integrated device
manufacturing requires surface cleanliness and surface smoothness in
wet chemical processing [1]. It is necessary to control all process
parameters perfectly especially for the common cleaning technique
RCA clean (SC-1 and SC-2) [2]. In this paper the characteristic and
effect of surface preparation parameters are discussed. The properties
of RCA wet chemical processing in silicon technology is based on
processing time, temperature, concentration and megasonic power of
SC-1 and QDR. An improvement of wafer surface preparation by
the enhanced variables of the wet cleaning chemical process is
proposed.
Abstract: Ciprofloxacin (CIP) and Carbamazepine (CBZ), nonbiodegradable pharmaceutical residues, were become emerging pollutants in several aquatic environments. The objectives of this research were to study the possibility to recover these pharmaceuticals residues from pharmaceutical wastewater by increasing the selective adsorption on synthesized functionalized porous silicate, comparing with powdered activated carbon (PAC). Hexagonal mesoporous silicate (HMS), functionalized HMSs (3- aminopropyltriethoxy, 3- mercaptopropyltrimethoxy and noctyldimethyl) were synthesized and characterized physico-chemical characteristics. Obtained adsorption kinetics and isotherms showed that 3-mercaptopropyltrimethoxy functional groups grafted on HMS provided highest CIP and CBZ adsorption capacities; however, it was still lower than that of PAC. The kinetic results were compatible with pseudo-second order. The hydrophobicity and hydrogen bonding might play a key role on the adsorption. Furthermore, the capacities were affected by varying pH values due to the strength of hydrogen bonding between targeted compounds and adsorbents. Electrostatic interaction might not affect the adsorption capacities.
Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.