Abstract: In this paper, an overview of the radio over fiber (RoF) technology is provided. Obstacles for reducing the capital and operational expenses in the existing systems are discussed in various perspectives. Some possible RoF deployment scenarios for WiMAX
data transmission are proposed as a means for capital and operational
expenses reduction. IEEE 802.16a standard based end-to-end physical layer model is simulated including intensity modulated direct detection RoF technology. Finally the feasibility of RoF
technology to carry WiMAX signals between the base station and the
remote antenna units is demonstrated using the simulation results.
Abstract: This paper considers the benefits gained by using an
efficient quality of service management such as DiffServ technique to
improve the performance of military communications. Low delay and
no blockage must be achieved especially for real time tactical data.
All traffic flows generated by different applications do not need same
bandwidth, same latency, same error ratio and this scalable technique
of packet management based on priority levels is analysed. End to
end architectures supporting various traffic flows and including lowbandwidth
and high-delay HF or SHF military links as well as
unprotected Internet sub domains are studied. A tuning of Diffserv
parameters is proposed in accordance with different loads of various
traffic and different operational situations.
Abstract: Soft set theory was initiated by Molodtsov in 1999. In the past years, this theory had been applied to many branches of mathematics, information science and computer science. In 2003, Maji et al. introduced some operations of soft sets and gave some operational rules. Recently, some of these operational rules are pointed out to be not true. Furthermore, Ali et al., in their paper, introduced and discussed some new operations of soft sets. In this paper, we further investigate these operational rules given by Maji et al. and Ali et al.. We obtain some sufficient-necessary conditions such that corresponding operational rules hold and give correct forms for some operational rules. These results will be help for us to use rightly operational rules of soft sets in research and application of soft set theory.
Abstract: A new design approach for three-stage operational
amplifiers (op-amps) is proposed. It allows to actually implement a
symmetrical push-pull class-AB amplifier output stage for wellestablished
three-stage amplifiers using a feedforward
transconductance stage. Compared with the conventional design
practice, the proposed approach leads to a significant
improvement of the symmetry between the positive and the
negative op-amp step response, resulting in similar values of the
positive/negative settling time. The new approach proves to be very
useful in order to fully exploit the potentiality allowed by the op-amp
in terms of speed performances. Design examples in a commercial
0.35-μm CMOS prove the effectiveness of theproposed strategy.
Abstract: Islamic institutions in Malaysia play a variety of
socioeconomic roles such as poverty alleviation. To perform this role,
these institutions face a major task in identifying the poverty group.
Most of these institutions measure and operationalize poverty from
the monetary perspective using variables such as income, expenditure
or consumption. In practice, most Islamic institutions in Malaysia use
the monetary approach in measuring poverty through the
conventional Poverty Line Income (PLI) method and recently, the
had al kifayah (HAK) method using total necessities of a household
from an Islamic perspective. The objective of this paper is to present
the PLI and also the HAK method. This micro-data study would
highlight the similarities and differences of both the methods.A
survey aided by a structured questionnaire was carried out on 260
selected head of households in the state of Selangor. The paper
highlights several demographic factors that are associated with the
three monetary indicators in the study, namely income, PLI and
HAK. In addition, the study found that these monetary variables are
significantly related with each other.
Abstract: Natural language processing systems pose a unique
challenge for software architectural design as system complexity has
increased continually and systems cannot be easily constructed from
loosely coupled modules. Lexical, syntactic, semantic, and pragmatic
aspects of linguistic information are tightly coupled in a manner that
requires separation of concerns in a special way in design,
implementation and maintenance. An aspect oriented software
architecture is proposed in this paper after critically reviewing
relevant architectural issues. For the purpose of this paper, the
syntactic aspect is characterized by an augmented context-free
grammar. The semantic aspect is composed of multiple perspectives
including denotational, operational, axiomatic and case frame
approaches. Case frame semantics matured in India from deep
thematic analysis. It is argued that lexical, syntactic, semantic and
pragmatic aspects work together in a mutually dependent way and
their synergy is best represented in the aspect oriented approach. The
software architecture is presented with an augmented Unified
Modeling Language.
Abstract: This paper presents the design and layout of a two stage, high speed operational amplifiers using standard 0.35um CMOS technology. The design procedure involves designing the bias circuit, the differential input pair, and the gain stage using CAD tools. Both schematic and layout of the operational amplifier along with the comparison in the results of the two has been presented. The operational amplifier designed, has a gain of 93.51db at low frequencies. It has a gain bandwidth product of 55.07MHz, phase margin of 51.9º and a slew rate of 22v/us for a load of capacitor of 10pF.
Abstract: In today scenario, to meet enhanced demand imposed
by domestic, commercial and industrial consumers, various
operational & control activities of Radial Distribution Network
(RDN) requires a focused attention. Irrespective of sub-domains
research aspects of RDN like network reconfiguration, reactive
power compensation and economic load scheduling etc, network
performance parameters are usually estimated by an iterative process
and is commonly known as load (power) flow algorithm. In this
paper, a simple mechanism is presented to implement the load flow
analysis (LFA) algorithm. The reported algorithm utilizes graph
theory principles and is tested on a 69- bus RDN.
Abstract: Intelligent Transportation System integrates various modern advanced technologies into the ground transportation system, and it will be the goal of urban transport system in the future because of its comprehensive effects. However, it also brings some problems, such as project performance assessment, fairness of benefiting groups, fund management, which are directly related to its operation and implementation. Wuhan has difficulties in organizing transportation because of its nature feature (river and lake), therefore, calling Service of Taxi plays an important role in transportation. This paper researches on calling Service of Taxi in Wuhan, based on quantitative and qualitative analysis. It analyzes its operations management systematically, including business model, finance, usage analysis and users evaluation. As for business model, it is that the government leads the operation at the initial stage, and the third part dominates the operation at the mature stage, which not only eases the pressure of the third part and benefits the spread of the calling service at the initial stage, but also alleviates financial pressure of government and improve the efficiency of the operation at the mature stage. As for finance, it draws that this service will bring heavy financial burden of equipments, but it will be alleviated in the future because of its spread. As for usage analysis, through data comparison, this service can bring some benefits for taxi drivers, and time and spatial distribution of usage have certain features. As for user evaluation, it analyzes using group and the reason why choosing it. At last, according to the analysis above, the paper puts forward the potentials, limitations, and future development strategies for it.
Abstract: The future of business intelligence (BI) is to integrate
intelligence into operational systems that works in real-time
analyzing small chunks of data based on requirements on continuous
basis. This is moving away from traditional approach of doing
analysis on ad-hoc basis or sporadically in passive and off-line mode
analyzing huge amount data. Various AI techniques such as expert
systems, case-based reasoning, neural-networks play important role
in building business intelligent systems. Since BI involves various
tasks and models various types of problems, hybrid intelligent
techniques can be better choice. Intelligent systems accessible
through web services make it easier to integrate them into existing
operational systems to add intelligence in every business processes.
These can be built to be invoked in modular and distributed way to
work in real time. Functionality of such systems can be extended to
get external inputs compatible with formats like RSS. In this paper,
we describe a framework that use effective combinations of these
techniques, accessible through web services and work in real-time.
We have successfully developed various prototype systems and done
few commercial deployments in the area of personalization and
recommendation on mobile and websites.
Abstract: The New Basel Capital Accord (Basel II) influences how financial institutions around the world, and especially European Union institutions, determine the amount of capital to reserve. However, as the recent global crisis has shown, the revision of Basel II is needed to reflect current trends, such as increased volatility and correlation, in the world financial markets. The overall objective of Basel II is to increase the safety and soundness of the international financial system. Basel II builds on three main pillars: Pillar I deals with the minimum capital requirements for credit, market and operational risk, Pillar II focuses on the supervisory review process and finally Pillar III promotes market discipline through enhanced disclosure requirements for banks. The aim of this paper is to provide the historical background, key features and impact of Basel II on financial markets. Moreover, we discuss new proposals for international bank regulation (sometimes referred to as Basel III) which include requirements for higher quality, constituency and transparency of banks' capital and risk management, regulation of OTC markets and introduction of new liquidity standards for internationally active banks.
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: This paper introduces a novel design for boring bar with enhanced damping capability. The principle followed in the design phase was to enhance the damping capability minimizing the loss in static stiffness through implementation of composite material interfaces. The newly designed tool has been compared to a conventional tool. The evaluation criteria were the dynamic characteristics, frequency and damping ratio, of the machining system, as well as the surface roughness of the machined workpieces. The use of composite material in the design of damped tool has been demonstrated effective. Furthermore, the autoregressive moving average (ARMA) models presented in this paper take into consideration the interaction between the elastic structure of the machine tool and the cutting process and can therefore be used to characterize the machining system in operational conditions.
Abstract: Author presents the results of a study conducted to identify criteria of efficient information system (IS) with serviceoriented architecture (SOA) realization and proposes a ranking method to evaluate SOA information systems using a set of architecture quality criteria before the systems are implemented. The method is used to compare 7 SOA projects and ranking result for SOA efficiency of the projects is provided. The choice of SOA realization project depends on following criteria categories: IS internal work and organization, SOA policies, guidelines and change management, processes and business services readiness, risk management and mitigation. The last criteria category was analyzed on the basis of projects statistics.
Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: Vitamin A deficiency is a public health problem in
Zimbabwe. Addressing vitamin A deficiency has the potential of
enhancing resistance to disease and reducing mortality especially in
children less than 5 years. We implemented and adapted vitamin A
outreach supplementation strategy within the National Immunization
Days and Extended Programme of Immunization in a rural district in
Zimbabwe. Despite usual operational challenges faced this approach
enabled the district to increase delivery of supplementation coverage.
This paper describes the outreach strategy that was implemented in
the remote rural district. The strategy covered 63 outreach sites with
2 sites being covered per day and visited once per month for the
whole year. Coverage reached 71% in an area of previous coverage
rates of around less than 50%. We recommend further exploration of
this strategy by others working in similar circumstances. This
strategy can be a potential way for use by Scaling-Up-Nutrition
member states.
Abstract: An experiment was conducted to examine the effect of the level of performance stabilization on the human adaptability to perceptual-motor perturbation in a complex coincident timing task. Three levels of performance stabilization were established operationally: pre-stabilization, stabilization, and super-stabilization groups. Each group practiced the task until reached its level of stabilization in a constant sequence of movements and under a constant time constraint before exposure to perturbation. The results clearly showed that performance stabilization is a pre-condition for adaptation. Moreover, variability before reaching stabilization is harmful to adaptation and persistent variability after stabilization is beneficial. Moreover, the behavior of variability is specific to each measure.
Abstract: Tubular process equipment is often damaged in
industrial processes. The damage occurs both on devices working at
high temperatures and also on less exposed devices. In case of sudden
damage of key equipment a shutdown of the whole production unit
and resulting significant economic losses are imminent. This paper
presents a solution of several types of tubular process equipment. The
causes of damage and suggestions of correction actions are discussed
in all cases. Very important part is the analysis of operational
conditions, determination of unfavourable working states decreasing
lifetime of devices and suggestions of correction actions. Lately very
popular numerical methods are used for analysis of the equipment.
Abstract: Earthmoving operations are a major part of many
construction projects. Because of the complexity and fast-changing
environment of such operations, the planning and estimating are
crucial on both planning and operational levels. This paper presents
the framework ofa microscopic discrete-event simulation system for
modeling earthmoving operations and conducting productivity
estimations on an operational level.A prototype has been developed
to demonstrate the applicability of the proposed framework, and this
simulation system is presented via a case study based on an actual
earthmoving project. The case study shows that the proposed
simulation model is capable of evaluating alternative operating
strategies and resource utilization at a very detailed level.