Abstract: In this paper, applying frequency domain approach, a delayed predator-prey fishery model with prey reserve is investigated. By choosing the delay τ as a bifurcation parameter, It is found that Hopf bifurcation occurs as the bifurcation parameter τ passes a sequence of critical values. That is, a family of periodic solutions bifurcate from the equilibrium when the bifurcation parameter exceeds a critical value. The length of delay which preserves the stability of the positive equilibrium is calculated. Some numerical simulations are included to justify the theoretical analysis results. Finally, main conclusions are given.
Abstract: This article proposes a current-mode square-rooting
circuit using current follower transconductance amplifier (CTFA).
The amplitude of the output current can be electronically controlled
via input bias current with wide input dynamic range. The proposed
circuit consists of only single CFTA. Without any matching
conditions and external passive elements, the circuit is then
appropriate for an IC architecture. The magnitude of the output signal
is temperature-insensitive. The PSpice simulation results are
depicted, and the given results agree well with the theoretical
anticipation. The power consumption is approximately 1.96mW at
±1.5V supply voltages.
Abstract: In this paper, a block code to minimize the peak-toaverage
power ratio (PAPR) of orthogonal frequency division
multiplexing (OFDM) signals is proposed. It is shown that cyclic
shift and codeword inversion cause not change to peak envelope
power. The encoding rule for the proposed code comprises of
searching for a seed codeword, shifting the register elements, and
determining codeword inversion, eliminating the look-up table for
one-to-one correspondence between the source and the coded data.
Simulation results show that OFDM systems with the proposed code
always have the minimum PAPR.
Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: In this study the integration of an absorption heat
pump (AHP) with the concentration section of an industrial pulp and
paper process is investigated using pinch technology. The optimum
design of the proposed water-lithium bromide AHP is then achieved
by minimizing the total annual cost. A comprehensive optimization is
carried out by relaxation of all stream pressure drops as well as heat
exchanger areas involving in AHP structure. It is shown that by
applying genetic algorithm optimizer, the total annual cost of the
proposed AHP is decreased by 18% compared to one resulted from
simulation.
Abstract: This paper describes a low-power second-order filter
for a continuous-time chopper stabilized capacitive sensor interface,
integrated with a fully differential post-CMOS surface-micromachined
MEMS pressure sensor. The circuit uses a single-ended
folded-cascode operational amplifier and two GM-C filters connected
in cascade. The circuit is realized in a 0.18 μm CMOS process and
offers differential to single-ended conversion. The novelty of the
scheme is the cascade of two GM-C filters to achieve a second-order
filter while minimizing power dissipation. The simulated filter cutoff
frequency is 1.14 kHz at common-mode voltage 1.65 V,
operating from a 3.3 V supply while dissipating 172μW of power.
The filter achieves an operating range of 1V for an output load of
1MOhm and 10pF.
Abstract: A local municipality has decided to build a sewage pit
to receive residential sewage waste arriving by tank trucks. Daily
accumulated waste are to be pumped to a nearby waste water
treatment facility to be re-consumed for agricultural and construction
projects. A discrete-event simulation model using Arena Software
was constructed to assist in defining the capacity of the system in
cubic meters, number of tank trucks to use the system, number of
unload docks required, number of standby areas needed and
manpower required for data collection at entrance checkpoint and
truck tank load toxicity testing. The results of the model are
statistically validated. Simulation turned out to be an excellent tool
in the facility planning effort for the pit project, as it insured smooth
flow lines of tank trucks load discharge and best utilization of
facilities on site.
Abstract: Given a bivariate normal sample of correlated variables,
(Xi, Yi), i = 1, . . . , n, an alternative estimator of Pearson’s correlation
coefficient is obtained in terms of the ranges, |Xi − Yi|.
An approximate confidence interval for ρX,Y is then derived, and
a simulation study reveals that the resulting coverage probabilities
are in close agreement with the set confidence levels. As well, a
new approximant is provided for the density function of R, the
sample correlation coefficient. A mixture involving the proposed
approximate density of R, denoted by hR(r), and a density function
determined from a known approximation due to R. A. Fisher is shown
to accurately approximate the distribution of R. Finally, nearly exact
density approximants are obtained on adjusting hR(r) by a 7th degree
polynomial.
Abstract: During the process of compaction in Hot-Mix Asphalt
(HMA) mixtures, the distance between aggregate particles decreases
as they come together and eliminate air-voids. By measuring the
inter-particle distances in a cut-section of a HMA sample the degree
of compaction can be estimated. For this, a calibration curve is
generated by computer simulation technique when the gradation and
asphalt content of the HMA mixture are known. A two-dimensional
cross section of HMA specimen was simulated using the mixture
design information (gradation, asphalt content and air-void content).
Nearest neighbor distance methods such as Delaunay triangulation
were used to study the changes in inter-particle distance and area
distribution during the process of compaction in HMA. Such
computer simulations would enable making several hundreds of
repetitions in a short period of time without the necessity to compact
and analyze laboratory specimens in order to obtain good statistics on
the parameters defined. The distributions for the statistical
parameters based on computer simulations showed similar trends as
those of laboratory specimens.
Abstract: In this paper, enhanced ground proximity warning simulation and validation system is designed and implemented. First, based on square grid and sub-grid structure, the global digital terrain database is designed and constructed. Terrain data searching is implemented through querying the latitude and longitude bands and separated zones of global terrain database with the current aircraft position. A combination of dynamic scheduling and hierarchical scheduling is adopted to schedule the terrain data, and the terrain data can be read and delete dynamically in the memory. Secondly, according to the scope, distance, approach speed information etc. to the dangerous terrain in front, and using security profiles calculating method, collision threat detection is executed in real-time, and provides caution and warning alarm. According to this scheme, the implementation of the enhanced ground proximity warning simulation system is realized. Simulations are carried out to verify a good real-time in terrain display and alarm trigger, and the results show simulation system is realized correctly, reasonably and stable.
Abstract: Viscous heating becomes significant in the high speed
resin coating process of glass fibers for optical fiber manufacturing.
This study focuses on the coating resin flows inside the capillary
coating die of optical fiber coating applicator and they are numerically
simulated to examine the effects of viscous heating and subsequent
temperature increase in coating resin. Resin flows are driven by fast
moving glass fiber and the pressurization at the coating die inlet, while
the temperature dependent viscosity of liquid coating resin plays an
important role in the resin flow. It is found that the severe viscous
heating near the coating die wall profoundly alters the radial velocity
profiles and that the increase of final coating thickness by die
pressurization is amplified if viscous heating is present.
Abstract: In this study, noise characteristics of structure were analyzed in an effort to reduce noise passing through an opening of an
enclosure surrounding the structure that generates noise. Enclosures
are essential measure to protect noise propagation from operating machinery. Access openings of the enclosures are important path of noise leakage. First, noise characteristics of structure were analyzed
and feed-forward noise control was performed using simulation in
order to reduce noise passing through the opening of enclosure, which
surrounds a structure generating noise. We then implemented a
feed-forward controller to actively control the acoustic power through
the opening. Finally, we conducted optimization of placement of the
reference sensors for several cases of the number of sensors. Good
control performances were achieved using the minimum number of microphones arranged an optimal placement.
Abstract: the paper presents the optimization results for several
electrical machines dedicated for powered electric wheel-chairs. The
optimization, using the Hook-Jeeves algorithm, was employed based
on a design approach which takes into consideration the road
conditions. Also, through numerical simulations (based on finite
element method), the analytical approach was validated. The
optimization approach gave satisfactory results and the best suited
variant was chosen for the motorization of the wheel-chair.
Abstract: In this paper, an automatic determination algorithm for nuclear magnetic resonance (NMR) spectra of the metabolites in the living body by magnetic resonance spectroscopy (MRS) without human intervention or complicated calculations is presented. In such method, the problem of NMR spectrum determination is transformed into the determination of the parameters of a mathematical model of the NMR signal. To calculate these parameters efficiently, a new model called modified Hopfield neural network is designed. The main achievement of this paper over the work in literature [30] is that the speed of the modified Hopfield neural network is accelerated. This is done by applying cross correlation in the frequency domain between the input values and the input weights. The modified Hopfield neural network can accomplish complex dignals perfectly with out any additinal computation steps. This is a valuable advantage as NMR signals are complex-valued. In addition, a technique called “modified sequential extension of section (MSES)" that takes into account the damping rate of the NMR signal is developed to be faster than that presented in [30]. Simulation results show that the calculation precision of the spectrum improves when MSES is used along with the neural network. Furthermore, MSES is found to reduce the local minimum problem in Hopfield neural networks. Moreover, the performance of the proposed method is evaluated and there is no effect on the performance of calculations when using the modified Hopfield neural networks.
Abstract: Stable bacterial polymorphism on a single limiting resource may appear if between the evolved strains metabolic interactions take place that allow the exchange of essential nutrients [8]. Towards an attempt to predict the possible outcome of longrunning evolution experiments, a network based on the metabolic capabilities of homogeneous populations of every single gene knockout strain (nodes) of the bacterium E. coli is reconstructed. Potential metabolic interactions (edges) are allowed only between strains of different metabolic capabilities. Bacterial communities are determined by finding cliques in this network. Growth of the emerged hypothetical bacterial communities is simulated by extending the metabolic flux balance analysis model of Varma et al [2] to embody heterogeneous cell population growth in a mutual environment. Results from aerobic growth on 10 different carbon sources are presented. The upper bounds of the diversity that can emerge from single-cloned populations of E. coli such as the number of strains that appears to metabolically differ from most strains (highly connected nodes), the maximum clique size as well as the number of all the possible communities are determined. Certain single gene deletions are identified to consistently participate in our hypothetical bacterial communities under most environmental conditions implying a pattern of growth-condition- invariant strains with similar metabolic effects. Moreover, evaluation of all the hypothetical bacterial communities under growth on pyruvate reveals heterogeneous populations that can exhibit superior growth performance when compared to the performance of the homogeneous wild-type population.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: Virtual touch screen using camera is an ordinary screen which uses a camera to imitate the touch screen by taking a picture of an indicator, e.g., finger, which is laid on the screen, converting the indicator tip position on the picture to the position on the screen, and moving the cursor on the screen to that position. In fact, the indicator is not laid on the screen directly, but it is intervened by the cover at some intervals. In spite of this gap, if the eye-indicator-camera angle is not large, the mapping from the indicator tip positions on the image to the corresponding cursor positions on the screen is not difficult and could be done with a little error. However, the larger the angle is, the bigger the error in the mapping occurs. This paper proposes cursor position estimation model for virtual touch screen using camera which could eliminate this kind of error. The proposed model (i) moves the on-screen pilot cursor to the screen position which locates on the screen at the position just behind the indicator tip when the indicator tip has been looked from the camera position, and then (ii) converts that pilot cursor position to the desirable cursor position (the position on the screen when it has been looked from the user-s eye through the indicator tip) by using the bilinear transformation. Simulation results show the correctness of the estimated cursor position by using the proposed model.
Abstract: This paper presents an analysis on the capacity and performance of MIMO-OFDM systems. The work is focused on the capacity of MIMO-OFDM systems over rician fading channel, in the case of the channel being known at the receiver only, which is more practical case of the channel. Simple expression for capacity is derived for the case of correlated rician fading. The performance of some MIMO-OFDM implementations with rician fading model is presented using an Alamouti coding scheme and Simulation results are obtained for both capacity and performance analysis.
Abstract: WiMAX is defined as Worldwide Interoperability for
Microwave Access by the WiMAX Forum, formed in June 2001 to
promote conformance and interoperability of the IEEE 802.16
standard, officially known as WirelessMAN. The attractive features
of WiMAX technology are very high throughput and Broadband
Wireless Access over a long distance. A detailed simulation
environment is demonstrated with the UGS, nrtPS and ertPS service
classes for throughput, delay and packet delivery ratio for a mixed
environment of fixed and mobile WiMAX. A simple mobility aspect
is considered for the mobile WiMAX and the PMP mode of
transmission is considered in TDD mode. The Network Simulator 2
(NS-2) is the tool which is used to simulate the WiMAX network
scenario. A simple Priority Scheduler and Weighted Round Robin
Schedulers are the WiMAX schedulers used in the research work
Abstract: In this paper a novel, simple and reliable digital firing
scheme has been implemented for speed control of three-phase
induction motor using ac voltage controller. The system consists of
three-phase supply connected to the three-phase induction motor via
three triacs and its control circuit. The ac voltage controller has three
modes of operation depending on the shape of supply current. The
performance of the induction motor differs in each mode where the
speed is directly proportional with firing angle in two modes and
inversely in the third one. So, the control system has to detect the
current mode of operation to choose the correct firing angle of triacs.
Three sensors are used to feed the line currents to control system to
detect the mode of operation. The control strategy is implemented
using a low cost Xilinx Spartan-3E field programmable gate array
(FPGA) device. Three PI-controllers are designed on FPGA to
control the system in the three-modes. Simulation of the system is
carried out using PSIM computer program. The simulation results
show stable operation for different loading conditions especially in
mode 2/3. The simulation results have been compared with the
experimental results from laboratory prototype.