Abstract: This current research focused on development of degradable starch based packaging film with enhanced mechanical properties. A series of low density polyethylene (LDPE)/tapioca starch compounds with various tapioca starch contents were prepared by twin screw extrusion with the addition of maleic anhydride grafted polyethylene as compatibilizer. Palm cooking oil was used as processing aid to ease the blown film process, thus, degradable film can be processed via conventional blown film machine. Studies on their characteristics, mechanical properties and biodegradation were carried out by Fourier Transform Infrared (FTIR) spectroscopy and optical properties, tensile test and exposure to fungi environment respectively. The presence of high starch contents had an adverse effect on the tensile properties of LDPE/tapioca starch blends. However, the addition of compatibilizer to the blends improved the interfacial adhesion between the two materials, hence, improved the tensile properties of the films. High content of starch amount also was found to increase the rate of biodegradability of LDPE/tapioca starch films. It can be proved by exposure of the film to fungi environment. A growth of microbes colony can be seen on the surface of LDPE/tapioca starch film indicates that the granular starch present on the surface of the polymer film is attacked by microorganisms, until most of it is assimilated as a carbon source.
Abstract: Sorghum flour was supplemented with 15 and 30%
chickpea flour. Sorghum flour and the supplement were fermented at
35 oC for 0, 8, 16, and 24 h. Changes in pH, titrable acidity, total
soluble solids, protein content, in vitro protein digestibility and
amino acid composition were investigated during fermentation and/or
after supplementation of sorghum flour with chickpea. The pH of the
fermenting material decreased sharply with a concomitant increase in
the titrable acidity. The total soluble solids remained unchanged with
progressive fermentation time. The protein content of sorghum
cultivar was found to be 9.27 and that of chickpea was 22.47%. The
protein content of sorghum cultivar after supplementation with15 and
30% chickpea was significantly (P ≤ 0.05) increased to 11.78 and
14.55%, respectively. The protein digestibility also increased after
fermentation from 13.35 to 30.59 and 40.56% for the supplements,
respectively. Further increment in protein content and digestibility
was observed when supplemented and unsupplemented samples were
fermented for different periods of time. Cooking of fermented
samples was found to increase the protein content slightly and
decreased digestibility for both supplements. Amino acid content of
fermented and fermented and cooked supplements was determined.
Supplementation was found to increase the lysine and therionine
content. Cooking following fermentation decreased lysine,
isoleucine, valine and sulfur containg amino acids.
Abstract: Dielectric sheet perturbation to the dominant TE111
mode resonant frequency of a circular cavity is studied and presented
in this paper. The dielectric sheet, placed at the middle of the airfilled
cavity, introduces discontinuities and disturbs the configuration
of electromagnetic fields in the cavity. For fixed dimensions of cavity
and fixed thickness of the loading dielectric, the dominant resonant
frequency varies quite linearly with the permittivity of the dielectric.
This quasi-linear relationship is plotted using Maple software and
verified using 3D electromagnetic simulations. Two probes are used
in the simulation for wave excitation into and from the cavity. The
best length of probe is found to be 3 mm, giving the closest resonant
frequency to the one calculated using Maple. A total of fourteen
different dielectrics of permittivity ranging from 1 to 12.9 are tested
one by one in the simulation. The works show very close agreement
between the results from Maple and the simulation. A constant
difference of 0.04 GHz is found between the resonant frequencies
collected during simulation and the ones from Maple. The success of
this project may lead to the possibility of using the middle loaded
cavity at TE111 mode as a microwave non-destructive testing of solid
materials.
Abstract: With the extensive inclusion of document, especially
text, in the business systems, data mining does not cover the full
scope of Business Intelligence. Data mining cannot deliver its impact
on extracting useful details from the large collection of unstructured
and semi-structured written materials based on natural languages.
The most pressing issue is to draw the potential business intelligence
from text. In order to gain competitive advantages for the business, it
is necessary to develop the new powerful tool, text mining, to expand
the scope of business intelligence.
In this paper, we will work out the strong points of text mining in
extracting business intelligence from huge amount of textual
information sources within business systems. We will apply text
mining to each stage of Business Intelligence systems to prove that
text mining is the powerful tool to expand the scope of BI. After
reviewing basic definitions and some related technologies, we will
discuss the relationship and the benefits of these to text mining. Some
examples and applications of text mining will also be given. The
motivation behind is to develop new approach to effective and
efficient textual information analysis. Thus we can expand the scope
of Business Intelligence using the powerful tool, text mining.
Abstract: Optical emission based on excitonic scattering processes becomes important in dense exciton systems in which the average distance between excitons is of the order of a few Bohr radii but still below the exciton screening threshold. The phenomena due to interactions among excited states play significant role in the emission near band edge of the material. The theory of two-exciton collisions for GaAs/AlGaAs quantum well systems is a mild attempt to understand the physics associated with the optical spectra due to excitonic scattering processes in these novel systems. The four typical processes considered give different spectral shape, peak position and temperature dependence of the emission spectra. We have used the theory of scattering together with the second order perturbation theory to derive the radiative power spontaneously emitted at an energy ħω by these processes. The results arrived at are purely qualitative in nature. The intensity of emitted light in quantum well systems varies inversely to the square of temperature, whereas in case of bulk materials it simply decreases with the temperature.
Abstract: Discharges in hydrogen, ignited by wire explosion, with current amplitude up to 1.5 MA were investigated. Channel diameter oscillations were observed on the photostreaks. Voltage and current curves correlated with the photostreaks. At initial gas pressure of 5-35 MPa the oscillation period was proportional to square root of atomic number of the initiating wire material. These oscillations were associated with aligned magnetic and gas-kinetic pressures. At initial pressure of 80-160 MPa acoustic pressure fluctuations on the discharge chamber wall were increased up to 150 MPa and there were the growth of voltage fluctuations on the discharge gap up to 3 kV simultaneously with it. In some experiments it was observed abrupt increase in the oscillation amplitude, which can be caused by the resonance of the acoustic oscillations in discharge chamber volume and the oscillations connected with alignment of the gaskinetic pressure and the magnetic pressure, as far as frequencies of these oscillations are close to each other in accordance with the estimates and the experimental data. Resonance of different type oscillations can produce energy density increasing in the discharge channel. Thus, the appropriate initial conditions in the experiment allow to increase the energy density in the discharge channel
Abstract: Soil microbial activity is adversely affected by pollutants such as heavy metals, antibiotics and pesticides. Organic amendments including sewage sludge, municipal compost and vermicompost are recently used to improve soil structure and fertility. But, these materials contain heavy metals including Pb, Cd, Zn, Ni and Cu that are toxic to soil microorganisms and may lead to occurrence of more tolerant microbes. Among these, Pb is the most abundant and has more negative effect on soil microbial ecology. In this study, Pb levels of 0, 100, 200, 300, 400 and 500 mg Pb [as Pb(NO3)2] per kg soil were added to the pots containing 2 kg of a loamy soil and incubated for 6 months at 25°C with soil moisture of - 0.3 MPa. Dehydrogenase activity of soil as a measure of microbial activity was determined on 15, 30, 90 and 180 days after incubation. Triphenyl tetrazolium chloride (TTC) was used as an electron acceptor in this assay. PICTs (IC50 values) were calculated for each Pb level and incubation time. Soil microbial activity was decreased by increasing Pb level during 30 days of incubation but the induced tolerance appeared on day 90 and thereafter. During 90 to 180 days of incubation, the PICT was gradually developed by increasing Pb level up to 200 mg kg-1, but the rate of enhancement was steeper at higher concentrations.
Abstract: The limit load carrying capacity of functionally
graded materials (FGM) circular plates subjected to an arbitrary
rotationally symmetric loading has been computed. It is provided that
the plate material behaves rigid perfectly plastic and obeys either the
Square or the Tresca yield criterion. To this end the upper and lower
bound principles of limit analysis are employed to determine the
exact value for the limiting load. The correctness of the result are
verified and finally limiting loads for two examples namely; through
radius and through thickness FGM circular plates with simply
supported edges are calculated, respectively and moreover, the values
of critical loading factor are determined.
Abstract: Vernacular building is considered as sustainable in
energy consumption and environment and its thermal performance is
more and more concerned by researchers. This paper investigates the
thermal property of the vernacular building in Lhasa by theoretical
analysis on the aspects of building form, envelope and materials etc.
The values of thermal resistance and thermal capacity of the envelope
are calculated and compared with the current China building code and
modern building case. And it is concluded that Lhasa vernacular
building meets the current China building code of thermal standards
and have better performance in some aspects, which is achieved by
various passive means with close response to local climate conditions.
Abstract: Permanent magnet synchronous machines are known
as a good candidate for hybrid electric vehicles due to their unique
merits. However they have two major drawbacks i.e. high cost and
small speed range. In this paper an optimal design of a permanent
magnet machine is presented. A reduction of permanent magnet
material for a constant torque and an extension in speed and torque
ranges are chosen as the optimization aims. For this purpose the
analytical model of the permanent magnet synchronous machine is
derived and the appropriate design algorithm is devised. The genetic
algorithm is then employed to optimize some machine specifications.
Finally the finite element method is used to validate the designed
machine.
Abstract: The objective of present work is to stimulate the
machining of material by electrical discharge machining (EDM) to
give effect of input parameters like discharge current (Ip), pulse on
time (Ton), pulse off time (Toff) which can bring about changes in the
output parameter, i.e. material removal rate. Experimental data was
gathered from die sinking EDM process using copper electrode and
Medium Carbon Steel (AISI 1040) as work-piece. The rules of
membership function (MF) and the degree of closeness to the
optimum value of the MMR are within the upper and lower range of
the process parameters. It was found that proposed fuzzy model is in
close agreement with the experimental results. By Intelligent, model
based design and control of EDM process parameters in this study
will help to enable dramatically decreased product and process
development cycle times.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.
Abstract: In this work, grinding or microcutting tools in the form of pellets were manufactured using a bounded alumina abrasive grains. The bound used is a vitreous material containing quartz feldspars, kaolinite and a quantity of hematite. The pellets were used in glass grinding process to replace the free abrasive grains lapping process. The study of the elaborated pellets were done to define their effectiveness in the grinding process and to optimize the influence of the pellets elaboration parameters. The obtained results show the existence of an optimal combination of the pellets elaboration parameters for each glass grinding phase (coarse to fine grinding). The final roughness (rms) reached by the elaborated pellets on a BK7 glass surface was about 0.392 μm.
Abstract: In this study, the precision heading process of
spur gears has been investigated by means of numerical
analysis. The effect of some parameters such as teeth number
and module on the forming force and material flow were
presented. The simulation works were performed rigid-plastic
finite element method using DEFORM 3D software. In order
to validate the estimated numerical results, they were
compared with those obtained experimentally during heading
of spur gear using lead as a model material. Results showed
that the optimum number of gear teeth is between 10 to 20,
that is because of being the specific pressure in its minimum
value.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: Low temperature (LT) is one of the most abiotic
stresses causing loss of yield in wheat (T. aestivum). Four major
genes in wheat (Triticum aestivum L.) with the dominant alleles
designated Vrn–A1,Vrn–B1,Vrn–D1 and Vrn4, are known to have
large effects on the vernalization response, but the effects on cold
hardiness are ambiguous. Poor cold tolerance has restricted winter
wheat production in regions of high winter stress [9]. It was known
that nearly all wheat chromosomes [5] or at least 10 chromosomes of
21 chromosome pairs are important in winter hardiness [15]. The
objective of present study was to clarify the role of each chromosome
in cold tolerance. With this purpose we used 20 isogenic lines of
wheat. In each one of these isogenic lines only a chromosome from
‘Bezostaya’ variety (a winter habit cultivar) was substituted to
‘Capple desprez’ variety. The plant materials were planted in
controlled conditions with 20º C and 16 h day length in moderately
cold areas of Iran at Karaj Agricultural Research Station in 2006-07
and the acclimation period was completed for about 4 weeks in a
cold room with 4º C. The cold hardiness of these isogenic lines was
measured by LT50 (the temperature in which 50% of the plants are
killed by freezing stress).The experimental design was completely
randomized block design (RCBD)with three replicates. The results
showed that chromosome 5A had a major effect on freezing
tolerance, and then chromosomes 1A and 4A had less effect on this
trait. Further studies are essential to understanding the importance of
each chromosome in controlling cold hardiness in wheat.
Abstract: Bicycle usage for exercise, recreation, and commuting
to work in Australia shows that pedal cycling is the fourth most
popular activity with 10.6% increase in participants between 2001
and 2007. As with other means of transport, accident and injury
becomes common although mandatory bicycle helmet wearing has
been introduced. The research aims to develop a face surrogate made
of sandwich of rigid foam and rubber sheets to represent human
facial bone under blunt impact. The facial surrogate will serve as an
important test device for further development of facial-impact
protection for cyclist. A test procedure was developed to simulate the
energy of impact and record data to evaluate the effect of impact on
facial bones. Drop tests were performed to establish a suitable
combination of materials. It was found that the sandwich structure of
rigid extruded-polystyrene foam (density of 40 kg/m3 with a pattern
of 6-mm-holes), Neoprene rubber sponge, and Abrasaflex rubber
backing, had impact characteristics comparable to that of human
facial bone. In particular, the foam thickness of 30 mm and 25 mm
was found suitable to represent human zygoma (cheekbone) and
maxilla (upper-jaw bone), respectively.
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: In the present research, a finite element model is
presented to study the geometrical and material nonlinear behavior of
reinforced concrete plane frames considering soil-structure
interaction. The nonlinear behaviors of concrete and reinforcing steel
are considered both in compression and tension up to failure. The
model takes account also for the number, diameter, and distribution
of rebar along every cross section. Soil behavior is taken into
consideration using four different models; namely: linear-, nonlinear
Winkler's model, and linear-, nonlinear continuum model. A
computer program (NARC) is specially developed in order to
perform the analysis. The results achieved by the present model show
good agreement with both theoretical and experimental published
literature. The nonlinear behavior of a rectangular frame resting on
soft soil up to failure using the proposed model is introduced for
demonstration.
Abstract: This research is to study the types of products and
services that employs 'ambient media and respective techniques in its
advertisement materials. Data collection has been done via analyses of a total of 62 advertisements that employed ambient media
approach in Thailand during the years 2004 to 2011. The 62 advertisement were qualifying advertisements of the Adman Awards
& Symposium under the category of Outdoor & Ambience. Analysis
results reveal that there is a total of 14 products and services that
chooses to utilize ambient media in its advertisement. Amongst all ambient media techniques, 'intrusion' uses the value of a medium in
its representation of content most often. Following intrusion is 'interaction', where consumers are invited to participate and interact
with the advertising materials. 'Illusion' ranks third in its ability to subject the viewers to distortions of reality that makes the division
between reality and fantasy less clear.