Abstract: In this study, participants with adjustment disorder with depressed mood (aged 18-54 years) with mild depression (N=18), severe depression (N=12) were compared with healthy controls (N=20) on the Multidimensional Aptitude Battery (MAB) a cognitive performance test. Using One Way Analysis of Variance and Matched Sample t-test. The results of the analysis shows that severely depressed participants performed poorly on the cognitive performance test relative to controls, however there were no significant differences on the cognitive performance test scores between the severely depressed and the mildly depressed. In addition, performance on the non-verbal performance subtest was poorer than that of the verbal subtest, suggesting that depression affects the executive functions of the person.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: Inner class is a specialized class that defined within a
regular outer class. It is used in some programming languages such as
Java to carry out the task which is related to its outer class. The
functional relatedness between inner class and outer class is always
the main concern of defining an inner class. However, excessive use
of inner class could sabotage the class cohesiveness. In addition,
excessive inner class leads to the difficulty of software maintenance
and comprehension. Our research aims at determining the minimum
threshold for the functional relatedness of inner-outer class. Such
minimum threshold is a guideline for removing or relocating the
excessive inner class. Our research provides a feasible way for
software developers to define inner classes which are functionally
related to the outer class.
Abstract: In this paper, we propose an improved 3D star skeleton
technique, which is a suitable skeletonization for human posture representation
and reflects the 3D information of human posture.
Moreover, the proposed technique is simple and then can be performed
in real-time. The existing skeleton construction techniques, such as
distance transformation, Voronoi diagram, and thinning, focus on the
precision of skeleton information. Therefore, those techniques are not
applicable to real-time posture recognition since they are computationally
expensive and highly susceptible to noise of boundary. Although
a 2D star skeleton was proposed to complement these problems,
it also has some limitations to describe the 3D information of the
posture. To represent human posture effectively, the constructed skeleton
should consider the 3D information of posture. The proposed 3D
star skeleton contains 3D data of human, and focuses on human action
and posture recognition. Our 3D star skeleton uses the 8 projection
maps which have 2D silhouette information and depth data of human
surface. And the extremal points can be extracted as the features of 3D
star skeleton, without searching whole boundary of object. Therefore,
on execution time, our 3D star skeleton is faster than the “greedy" 3D
star skeleton using the whole boundary points on the surface. Moreover,
our method can offer more accurate skeleton of posture than the
existing star skeleton since the 3D data for the object is concerned.
Additionally, we make a codebook, a collection of representative 3D
star skeletons about 7 postures, to recognize what posture of constructed
skeleton is.
Abstract: In this work, Experimental tie-line results and
solubility (binodal) curves were obtained for the ternary systems
(water + acetic acid + methyl isobutyl ketone (MIBK)), (water +
lactic acid+ methyl isobutyl ketone) at T = 294.15K and atmospheric
pressure. The consistency of the values of the experimental tie-lines
was determined through the Othmer-Tobias and Hands correlations.
For the extraction effectiveness of solvents, the distribution and
selectivity curves were plotted. In addition, these experimental tieline
data were also correlated with NRTL model. The interaction
parameters for the NRTL model were retrieved from the obtained
experimental results by means of a combination of the homotopy
method and the genetic algorithms.
Abstract: At present, intelligent planning in the Graphplan framework is a focus of artificial intelligence. While the Creating or Destroying Objects Planning (CDOP) is one unsolved problem of this field, one of the difficulties, too. In this paper, we study this planning problem and bring forward the idea of transforming objects to propositions, based on which we offer an algorithm, Creating or Destroying Objects in the Graphplan framework (CDOGP). Compared to Graphplan, the new algorithm can solve not only the entire problems that Graphplan do, but also a part of CDOP. It is for the first time that we introduce the idea of object-proposition, and we emphasize the discussion on the representations of creating or destroying objects operator and an algorithm in the Graphplan framework. In addition, we analyze the complexity of this algorithm.
Abstract: Owing the fact that optimization of business process
is a crucial requirement to navigate, survive and even thrive in
today-s volatile business environment, this paper presents a
framework for selecting a best-fit optimization package for solving
complex business problems. Complexity level of the problem and/or
using incorrect optimization software can lead to biased solutions of
the optimization problem. Accordingly, the proposed framework
identifies a number of relevant factors (e.g. decision variables,
objective functions, and modeling approach) to be considered during
the evaluation and selection process. Application domain, problem
specifications, and available accredited optimization approaches are
also to be regarded. A recommendation of one or two optimization
software is the output of the framework which is believed to provide
the best results of the underlying problem. In addition to a set of
guidelines and recommendations on how managers can conduct an
effective optimization exercise is discussed.
Abstract: In order to evaluate the relationship between the sulphur (S), glucose (G), nitrogen (N) and plant residues (st), sulphur immobilization and microbial transformation were monitored in five soil samples from 0-30 cm of Bastam farmers fields of Shahrood area following 11 treatments with different levels of Sulphur (S), glucose (G), N and plant residues (wheat straw) in a randomized block design with three replications and incubated over 20, 45 and 60 days, the immobilization of SO4 -2-S presented as a percentage of that added, was inversely related to its addition rate. Additions of glucose and plant residues increased with the C-to-S ratio of the added amendments, irrespective of their origins (glucose and plant residues). In the presence of C sources (glucose or plant residues). N significantly increased the immobilization of SO4 -2-S, whilst the effect of N was insignificant in the absence of a C amendment. In first few days the amounts of added SO4 -2-S immobilized were linearly correlated with the amounts of added S recovered in the soil microbial biomass. With further incubation the proportions of immobilized SO4 -2-S remaining as biomass-S decreased. Decrease in biomass-S was thought to be due to the conversion of biomass-S into soil organic-S. Glucose addition increased the immobilization (microbial utilization and incorporation into the soil organic matter) of native soil SO4 -2-S. However, N addition enhance the mineralization of soil organic-S, increasing the concentration of SO4 - 2-S in soil.
Abstract: In molecular biology, microarray technology is widely and successfully utilized to efficiently measure gene activity. If working with less studied organisms, methods to design custom-made microarray probes are available. One design criterion is to select probes with minimal melting temperature variances thus ensuring similar hybridization properties. If the microarray application focuses on the investigation of metabolic pathways, it is not necessary to cover the whole genome. It is more efficient to cover each metabolic pathway with a limited number of genes. Firstly, an approach is presented which minimizes the overall melting temperature variance of selected probes for all genes of interest. Secondly, the approach is extended to include the additional constraints of covering all pathways with a limited number of genes while minimizing the overall variance. The new optimization problem is solved by a bottom-up programming approach which reduces the complexity to make it computationally feasible. The new method is exemplary applied for the selection of microarray probes in order to cover all fungal secondary metabolite gene clusters for Aspergillus terreus.
Abstract: The paper discusses a 3D numerical solution of the inverse boundary problem for a continuous casting process of alloy. The main goal of the analysis presented within the paper was to estimate heat fluxes along the external surface of the ingot. The verified information on these fluxes was crucial for a good design of a mould, effective cooling system and generally the whole caster. In the study an enthalpy-porosity technique implemented in Fluent package was used for modeling the solidification process. In this method, the phase change interface was determined on the basis of the liquid fraction approach. In inverse procedure the sensitivity analysis was applied for retrieving boundary conditions. A comparison of the measured and retrieved values showed a high accuracy of the computations. Additionally, the influence of the accuracy of measurements on the estimated heat fluxes was also investigated.
Abstract: In recent years various types of electric vehicles
has gained again increasing attention as an environmentally
benign technology in transport. Especially for urban areas with
high local pollution this Zero-emission technology (at the point
of use) is considered to provide proper solutions. Yet, the bad
economics and the limited driving ranges are still major barriers
for a broader market penetration of battery electric vehicles
(BEV) and of fuel cell vehicles (FCV). The major result of our
analyses is that the most important precondition for a further
dissemination of BEV in urban areas are emission-free zones.
This is an instrument which allows the promotion of BEV
without providing excessive subsidies. In addition, it is
important to note that the full benefits of EV can only be
harvested if the electricity used is produced from renewable
energy sources. That is to say, it has to be ensured that the use of
BEV in urban areas is clearly linked to a green electricity
purchase model. And moreover, the introduction of a CO2-
emission-based tax system would support this requirement.
Abstract: Synthetic Aperture Radar (SAR) is an imaging radar form by taking full advantage of the relative movement of the antenna with respect to the target. Through the simultaneous processing of the radar reflections over the movement of the antenna via the Range Doppler Algorithm (RDA), the superior resolution of a theoretical wider antenna, termed synthetic aperture, is obtained. Therefore, SAR can achieve high resolution two dimensional imagery of the ground surface. In addition, two filtering steps in range and azimuth direction provide accurate enough result. This paper develops a simulation in which realistic SAR images can be generated. Also, the effect of velocity errors in the resulting image has also been investigated. Taking some velocity errors into account, the simulation results on the image resolution would be presented. Most of the times, algorithms need to be adjusted for particular datasets, or particular applications.
Abstract: In order to enhance the usability of the human computer interface (HCI) on the touchscreen, this study explored the optimal tactile depth and effect of visual cues on the user-s tendency to touch the touchscreen icons. The experimental program was designed on the touchscreen in this study. Results indicated that the ratio of the icon size to the tactile depth was 1:0.106. There were significant effects of experienced users and novices on the tactile feedback depth (p < 0.01). In addition, the results proved that the visual cues provided a feedback that helped to guide the user-s touch icons accurately and increased the capture efficiency for a tactile recognition field. This tactile recognition field was 18.6 mm in length. There was consistency between the experienced users and novices under the visual cue effects. Finally, the study developed an applied design with touch feedback for touchscreen icons.
Abstract: The elimination of ranitidine (a pharmaceutical
compound) has been carried out in the presence of UV-C radiation.
After some preliminary experiments, it has been experienced the no
influence of the gas nature (air or oxygen) bubbled in photolytic
experiments. From simple photolysis experiments the quantum yield
of this compound has been determined. Two photolytic
approximation has been used, the linear source emission in parallel
planes and the point source emission in spherical planes. The
quantum yield obtained was in the proximity of 0.05 mol Einstein-1
regardless of the method used. Addition of free radical promoters
(hydrogen peroxide) increases the ranitidine removal rate while the
use of photocatalysts (TiO2) negatively affects the process.
Abstract: Tumour suppressors are key participants in the
prevention of cancer. Regulation of their expression through
miRNAs is important for comprehensive translation inhibition of
tumour suppressors and elucidation of carcinogenesis mechanisms.
We studies the possibility of 1521 miRNAs to bind with 873 mRNAs
of human tumour suppressors using RNAHybrid 2.1 and ERNAhybrid
programmes. Only 978 miRNAs were found to be
translational regulators of 812 mRNAs, and 61 mRNAs did not have
any miRNA binding sites. Additionally, 45.9% of all miRNA binding
sites were located in coding sequences (CDSs), 33.8% were located
in 3' untranslated region (UTR), and 20.3% were located in the
5'UTR. MiRNAs binding with more than 50 target mRNAs and
mRNAs binding with several miRNAs were selected. Hsa-miR-5096
had 15 perfectly complementary binding sites with mRNAs of 14
tumour suppressors. These newly indentified miRNA binding sites
can be used in the development of medicines (anti-sense therapies)
for cancer treatment.
Abstract: Equations with differentials relating to the inverse of an unknown function rather than to the unknown function itself are solved exactly for some special cases and numerically for the general case. Invertibility combined with differentiability over connected domains forces solutions always to be monotone. Numerical function inversion is key to all solution algorithms which either are of a forward type or a fixed point type considering whole approximate solution functions in each iteration. The given considerations are restricted to ordinary differential equations with inverted functions (ODEIs) of first order. Forward type computations, if applicable, admit consistency of order one and, under an additional accuracy condition, convergence of order one.
Abstract: The aims of this study were to compare the
differences of being good membership behavior among faculties and
staffs of Suan Sunandha Rajabhat University with different sex, age,
income, education, marital status, and working period, and
investigate the relationships between organizational commitment and
being good membership behavior. The research methodology
employed a questionnaire as a quantitative method. The respondents
were 305 faculties and staffs of Suan Sunandha Rajabhat University.
This research used Percentage, Mean, Standard Deviation, t-test,
One-Way ANOVA Analysis of Variance, and Pearson’s Product
Moment Correlation Coefficient in data analysis. The results showed
that organizational commitment among faculties and staffs of Suan
Sunandha Rajabhat University was at a high level. In addition,
differences in sex, age, income, education, marital status, and
working period revealed differences in being good membership
behavior. The results also indicated that organizational commitment
was significantly related to being good membership behavior.
Abstract: Medical images require special safety and confidentiality because critical judgment is done on the information provided by medical images. Transmission of medical image via internet or mobile phones demands strong security and copyright protection in telemedicine applications. Here, highly secured and robust watermarking technique is proposed for transmission of image data via internet and mobile phones. The Region of Interest (ROI) and Non Region of Interest (RONI) of medical image are separated. Only RONI is used for watermark embedding. This technique results in exact recovery of watermark with standard medical database images of size 512x512, giving 'correlation factor' equals to 1. The correlation factor for different attacks like noise addition, filtering, rotation and compression ranges from 0.90 to 0.95. The PSNR with weighting factor 0.02 is up to 48.53 dBs. The presented scheme is non blind and embeds hospital logo of 64x64 size.
Abstract: This paper argues that a product development exercise
involves in addition to the conventional stages, several decisions
regarding other aspects. These aspects should be addressed
simultaneously in order to develop a product that responds to the
customer needs and that helps realize objectives of the stakeholders
in terms of profitability, market share and the like. We present a
framework that encompasses these different development
dimensions. The framework shows that a product development
methodology such as the Quality Function Deployment (QFD) is the
basic tool which allows definition of the target specifications of a
new product. Creativity is the first dimension that enables the
development exercise to live and end successfully. A number of
group processes need to be followed by the development team in
order to ensure enough creativity and innovation. Secondly,
packaging is considered to be an important extension of the product.
Branding strategies, quality and standardization requirements,
identification technologies, design technologies, production
technologies and costing and pricing are also integral parts to the
development exercise. These dimensions constitute the proposed
framework. The paper also presents a mathematical model used to
calculate the design targets based on the target costing principle. The
framework is used to study a case of a new product development in
the telecommunications services sector.
Abstract: Organizational structure of the Turkish state
universities is a form of bureaucracy, a high efficient system in
rational and formal control. According to the dimensional approach
bureaucracy can occur in an organization in a degree, as some
bureaucracy characteristics can be stronger than others. In addition,
the units of an organization due to their different specific
characteristic properties can perceive the bureaucracy differently. In
the study, Hall-s Organizational Inventory, which was developed for
evaluating the degree of bureaucratization from the dimensional
perspective, is used to find out if there is a difference in the
perception of the bureaucracy between the academicians working in
three different departments and two faculties in the same university.