Abstract: This paper presents the use of anti-sway angle control
approaches for a two-dimensional gantry crane with disturbances
effect in the dynamic system. Delayed feedback signal (DFS) and
proportional-derivative (PD)-type fuzzy logic controller are the
techniques used in this investigation to actively control the sway
angle of the rope of gantry crane system. A nonlinear overhead
gantry crane system is considered and the dynamic model of the
system is derived using the Euler-Lagrange formulation. A complete
analysis of simulation results for each technique is presented in time
domain and frequency domain respectively. Performances of both
controllers are examined in terms of sway angle suppression and
disturbances cancellation. Finally, a comparative assessment of the
impact of each controller on the system performance is presented and
discussed.
Abstract: Undular hydraulic jumps are illustrated by a smooth
rise of the free surface followed by a train of stationary waves. They
are sometimes experienced in natural waterways and rivers. The
characteristics of undular hydraulic jumps are studied here. The
height, amplitude and the main characteristics of undular jump is
depended on the upstream Froude number and aspect ratio. The
experiments were done on the smooth bed flume. These results
compared with other researches and the main characteristics of the
undular hydraulic jump were studied in this article.
Abstract: Fourier transform infrared (FT-IR) spectroscopic imaging
is an emerging technique that provides both chemically and
spatially resolved information. The rich chemical content of data
may be utilized for computer-aided determinations of structure and
pathologic state (cancer diagnosis) in histological tissue sections for
prostate cancer. FT-IR spectroscopic imaging of prostate tissue has
shown that tissue type (histological) classification can be performed to
a high degree of accuracy [1] and cancer diagnosis can be performed
with an accuracy of about 80% [2] on a microscopic (≈ 6μm)
length scale. In performing these analyses, it has been observed
that there is large variability (more than 60%) between spectra from
different points on tissue that is expected to consist of the same
essential chemical constituents. Spectra at the edges of tissues are
characteristically and consistently different from chemically similar
tissue in the middle of the same sample. Here, we explain these
differences using a rigorous electromagnetic model for light-sample
interaction. Spectra from FT-IR spectroscopic imaging of chemically
heterogeneous samples are different from bulk spectra of individual
chemical constituents of the sample. This is because spectra not
only depend on chemistry, but also on the shape of the sample.
Using coupled wave analysis, we characterize and quantify the nature
of spectral distortions at the edges of tissues. Furthermore, we
present a method of performing histological classification of tissue
samples. Since the mid-infrared spectrum is typically assumed to
be a quantitative measure of chemical composition, classification
results can vary widely due to spectral distortions. However, we
demonstrate that the selection of localized metrics based on chemical
information can make our data robust to the spectral distortions
caused by scattering at the tissue boundary.
Abstract: Ramadan requires individuals to abstain from food and fluid intake between sunrise and sunset; physiological considerations predict that poorer mood, physical performance and mental performance will result. In addition, any difficulties will be worsened because preparations for fasting and recovery from it often mean that nocturnal sleep is decreased in length, and this independently affects mood and performance.
A difficulty of interpretation in many studies is that the observed changes could be due to fasting but also to the decreased length of sleep and altered food and fluid intakes before and after the daytime fasting. These factors were separated in this study, which took place over three separate days and compared the effects of different durations of fasting (4, 8 or 16h) upon a wide variety of measures (including subjective and objective assessments of performance, body composition, dehydration and responses to a short bout of exercise) - but with an unchanged amount of nocturnal sleep, controlled supper the previous evening, controlled intakes at breakfast and daytime naps not being allowed. Many of the negative effects of fasting observed in previous studies were present in this experiment also. These findings indicate that fasting was responsible for many of the changes previously observed, though some effect of sleep loss, particularly if occurring on successive days (as would occur in Ramadan) cannot be excluded.
Abstract: Since injection engines have a considerable portion, in
consumption of energy and environmental pollution, using an
alternative source of energy with lower pollutant effects in this
regard is necessary.
Biodiesel fuel is a suitable alternative for gasoline in diesel
engines.
In this research the property of biodiesel, the function and the
pollution effects of diesel engine, when using 100% biodiesel, using
100% gasoline and mixing ratio of both fuels for comparing them,
have been investigated.
The researches have shown, using biodiesel fuel in prevalent
diesel engine, will reduce the pollutants such as Co, half burned
carbohydrate and suspended particles and a little increase in
oxidation will achieve while power consumption, particularly fuel
and thermal efficiency of diesel fuel has the same.
Abstract: The purpose of this paper is to investigate the adjust-
ment of solar shading devices in office buildings in two different
seasons by occupants, and its influence on the lighting control and
indoor illuminance levels. The results show that occupants take
inappropriate measures both in reducing solar radiation in summer
and in admitting solar gains in winter, resulting in an increase in
lighting energy and a reduction in indoor illuminance. Therefore,
movable shading devices, controlled automatically, are suitable for
building applications to reduce energy consumption.
Abstract: In this paper, we present a comparative study between two computer vision systems for objects recognition and tracking, these algorithms describe two different approach based on regions constituted by a set of pixels which parameterized objects in shot sequences. For the image segmentation and objects detection, the FCM technique is used, the overlapping between cluster's distribution is minimized by the use of suitable color space (other that the RGB one). The first technique takes into account a priori probabilities governing the computation of various clusters to track objects. A Parzen kernel method is described and allows identifying the players in each frame, we also show the importance of standard deviation value research of the Gaussian probability density function. Region matching is carried out by an algorithm that operates on the Mahalanobis distance between region descriptors in two subsequent frames and uses singular value decomposition to compute a set of correspondences satisfying both the principle of proximity and the principle of exclusion.
Abstract: Documents clustering become an essential technology
with the popularity of the Internet. That also means that fast and
high-quality document clustering technique play core topics. Text
clustering or shortly clustering is about discovering semantically
related groups in an unstructured collection of documents. Clustering
has been very popular for a long time because it provides unique
ways of digesting and generalizing large amounts of information.
One of the issues of clustering is to extract proper feature (concept)
of a problem domain. The existing clustering technology mainly
focuses on term weight calculation. To achieve more accurate
document clustering, more informative features including concept
weight are important. Feature Selection is important for clustering
process because some of the irrelevant or redundant feature may
misguide the clustering results. To counteract this issue, the proposed
system presents the concept weight for text clustering system
developed based on a k-means algorithm in accordance with the
principles of ontology so that the important of words of a cluster can
be identified by the weight values. To a certain extent, it has resolved
the semantic problem in specific areas.
Abstract: A mathematical model for the Dynamics of Economic
Profit is constructed by proposing a characteristic differential oneform
for this dynamics (analogous to the action in Hamiltonian
dynamics). After processing this form with exterior calculus, a pair of
characteristic differential equations is generated and solved for the
rate of change of profit P as a function of revenue R (t) and cost C (t).
By contracting the characteristic differential one-form with a vortex
vector, the Lagrangian is obtained for the Dynamics of Economic
Profit.
Abstract: When reconstructing a scenario, it is necessary to
know the structure of the elements present on the scene to have an
interpretation. In this work we link 3D scenes reconstruction to
evolutionary algorithms through the vision stereo theory. We
consider vision stereo as a method that provides the reconstruction of
a scene using only a couple of images of the scene and performing
some computation. Through several images of a scene, captured from
different positions, vision stereo can give us an idea about the threedimensional
characteristics of the world. Vision stereo usually
requires of two cameras, making an analogy to the mammalian vision
system. In this work we employ only a camera, which is translated
along a path, capturing images every certain distance. As we can not
perform all computations required for an exhaustive reconstruction,
we employ an evolutionary algorithm to partially reconstruct the
scene in real time. The algorithm employed is the fly algorithm,
which employ “flies" to reconstruct the principal characteristics of
the world following certain evolutionary rules.
Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.
Abstract: This paper proposes a method, combining color and layout features, for identifying documents captured from low-resolution handheld devices. On one hand, the document image color density surface is estimated and represented with an equivalent ellipse and on the other hand, the document shallow layout structure is computed and hierarchically represented. Our identification method first uses the color information in the documents in order to focus the search space on documents having a similar color distribution, and finally selects the document having the most similar layout structure in the remaining of the search space.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: In the past years, the world has witnessed significant work in the field of Manufacturing. Special efforts have been made in the implementation of new technologies, management and control systems, among many others which have all evolved the field. Closely following all this, due to the scope of new projects and the need of turning the existing flexible ideas into more autonomous and intelligent ones, i.e.: moving toward a more intelligent manufacturing, the present paper emerges with the main aim of contributing to the analysis and a few customization issues of a new iCIM 3000 system at the IPSAM. In this process, special emphasis in made on the material flow problem. For this, besides offering a description and analysis of the system and its main parts, also some tips on how to define other possible alternative material flow scenarios and a partial analysis of the combinatorial nature of the problem are offered as well. All this is done with the intentions of relating it with the use of simulation tools, for which these have been briefly addressed with a special focus on the Witness simulation package. For a better comprehension, the previous elements are supported by a few figures and expressions which would help obtaining necessary data. Such data and others will be used in the future, when simulating the scenarios in the search of the best material flow configurations.
Abstract: A catastrophic earthquake measuring 6.3 on the
Richter scale struck the Christchurch, New Zealand Central Business
District on February 22, 2012, abruptly disrupting the business of
teaching and learning at Christchurch Polytechnic Institute of
Technology. This paper presents the findings from a study
undertaken about the complexity of delivering an educational
programme in the face of this traumatic natural event. Nine
interconnected themes emerged from this multiple method study:
communication, decision making, leader- and follower-ship,
balancing personal and professional responsibilities, taking action,
preparedness and thinking ahead, all within a disruptive and uncertain
context. Sustainable responses that maximise business continuity, and
provide solutions to practical challenges, are among the study-s
recommendations.
Abstract: Design and modeling of nonlinear systems require the
knowledge of all inside acting parameters and effects. An empirical
alternative is to identify the system-s transfer function from input and
output data as a black box model. This paper presents a procedure
using least squares algorithm for the identification of a feed drive
system coefficients in time domain using a reduced model based on
windowed input and output data. The command and response of the
axis are first measured in the first 4 ms, and then least squares are
applied to predict the transfer function coefficients for this
displacement segment. From the identified coefficients, the next
command response segments are estimated. The obtained results
reveal a considerable potential of least squares method to identify the
system-s time-based coefficients and predict accurately the command
response as compared to measurements.
Abstract: Lately, significant work in the area of Intelligent
Manufacturing has become public and mainly applied within the
frame of industrial purposes. Special efforts have been made in the
implementation of new technologies, management and control
systems, among many others which have all evolved the field. Aware
of all this and due to the scope of new projects and the need of
turning the existing flexible ideas into more autonomous and
intelligent ones, i.e.: Intelligent Manufacturing, the present paper
emerges with the main aim of contributing to the design and analysis
of the material flow in either systems, cells or work stations under
this new “intelligent" denomination. For this, besides offering a
conceptual basis in some of the key points to be taken into account
and some general principles to consider in the design and analysis of
the material flow, also some tips on how to define other possible
alternative material flow scenarios and a classification of the states a
system, cell or workstation are offered as well. All this is done with
the intentions of relating it with the use of simulation tools, for which
these have been briefly addressed with a special focus on the Witness
simulation package. For a better comprehension, the previous
elements are supported by a detailed layout, other figures and a few
expressions which could help obtaining necessary data. Such data and
others will be used in the future, when simulating the scenarios in the
search of the best material flow configurations.
Abstract: The objective of this paper is to construct a creativity
composite index designed to capture the growing role of creativity in
driving economic and social development for the 27 European Union
countries.
The paper proposes a new approach for the measurement of EU-27
creative potential and for determining its capacity to attract and
develop creative human capital. We apply a modified version of the
3T model developed by Richard Florida and Irene Tinagli for
constructing a Euro-Creativity Index. The resulting indexes establish
a quantitative base for policy makers, supporting their efforts to
determine the contribution of creativity to economic development.
Abstract: Candida albicans ATCC 10231 had low endogenous activity of the alternative oxidase compared with that of C. albicans ATCC 10261. In C. albicans ATCC 10231 the endogenous activity declined as the cultures aged. Alternative oxidase activity could be induced in C. albicans ATCC 10231 by treatment with cyanide, but the induction of this activity required the presence of oxygen which could be replaced, at least in part, with high concentrations of potassium ferricyanide. We infer from this that the expression of the gene encoding the alternative oxidase is under the control of a redoxsensitive transcription factor.