Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: The approach proposed here is oriented in the direction of fuzzy system for the analysis and the synthesis of intelligent climate controllers, the simulation of the internal climate of the greenhouse is achieved by a linear model whose coefficients are obtained by identification. The use of fuzzy logic controllers for the regulation of climate variables represents a powerful way to minimize the energy cost. Strategies of reduction and optimization are adopted to facilitate the tuning and to reduce the complexity of the controller.
Abstract: Renewed interest in propeller propulsion on aircraft
configurations combined with higher propeller loads lead to the question how the effects of the propulsion on model support disturbances
should be accounted for. In this paper, the determination of engine power effects on support interference of sting-mounted models is
demonstrated by a measurement on a four-engine turboprop aircraft.
CFD results on a more generic model are presented in order to clarify
the possible mechanism behind engine power effects on support
interference. The engine slipstream induces a local change in angle
of sideslip at the model sting thereby influencing the sting near-field and far-field effects. Whether or not the net result of these changes
in the disturbance pattern leads to a significant engine power effect depends on the configuration of the wind tunnel model and the test
setup.
Abstract: In a liberalized electricity market, it is not surprising
that different customers require different power quality (PQ) levels at
different price. Power quality related to several power disturbances is
described by many parameters, so how to define a comprehensive
hierarchy evaluation system of power quality (PQCHES) has become
a concerned issue. In this paper, based on four electromagnetic
compatibility (EMC) levels, the numerical range of each power
disturbance is divided into five grades (Grade I –Grade V), and the
“barrel principle" of power quality is used for the assessment of
overall PQ performance with only one grade indicator. A case study
based on actual monitored data of PQ shows that the site PQ grade
indicates the electromagnetic environment level and also expresses the
characteristics of loads served by the site.
The shortest plank principle of PQ barrel is an incentive
mechanism, which can combine with the rewards/penalty mechanism
(RPM) of consumed energy “on quality demand", to stimulate utilities
to improve the overall PQ level and also stimulate end-user more
“smart" under the infrastructure of future SmartGrid..
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.
Abstract: The aim of this study was to remove the two principal
noises which disturb the surface electromyography signal
(Diaphragm). These signals are the electrocardiogram ECG artefact
and the power line interference artefact. The algorithm proposed
focuses on a new Lean Mean Square (LMS) Widrow adaptive
structure. These structures require a reference signal that is correlated
with the noise contaminating the signal. The noise references are
then extracted : first with a noise reference mathematically
constructed using two different cosine functions; 50Hz (the
fundamental) function and 150Hz (the first harmonic) function for
the power line interference and second with a matching pursuit
technique combined to an LMS structure for the ECG artefact
estimation. The two removal procedures are attained without the use
of supplementary electrodes. These techniques of filtering are
validated on real records of surface diaphragm electromyography
signal. The performance of the proposed methods was compared with
already conducted research results.
Abstract: This study was conducted to determine the
effect of abdominal exercises versus abdominal supporting
belt on abdominal efficiency and inter-recti separation
following vaginal delivery.30 primiparous post-natal women
participated in this study. Their age ranged from (25 - 35)
years and their BMI < 30 Kg/m2. Participants were assigned
randomly into 2groups, participants of group (A) used
abdominal belt from the 2nd day following delivery, till the end
of puerperium (6 weeks), while participants of group (B)
engaged into abdominal exercises program from the 2nd day
following delivery for 6 weeks. The results of the present
study revealed that although there was no statistical difference
in waist circumference between both groups, participation in
abdominal exercise program produced a pronounced reduction
in waist/hip ratio, and inter-recti separation and also caused
significant increase in abdominal muscles strength (peak
torque, maximum repetition total work and average power)
higher than the use of abdominal belt.
Abstract: This paper proposes a set of quasi-static mathematical
model of magnetic fields caused by high voltage conductors of
distribution transformer by using a set of second-order partial
differential equation. The modification for complex magnetic field
analysis and time-harmonic simulation are also utilized. In this
research, transformers were study in both balanced and unbalanced
loading conditions. Computer-based simulation utilizing the threedimensional
finite element method (3-D FEM) is exploited as a tool
for visualizing magnetic fields distribution volume a distribution
transformer. Finite Element Method (FEM) is one among popular
numerical methods that is able to handle problem complexity in
various forms. At present, the FEM has been widely applied in most
engineering fields. Even for problems of magnetic field distribution,
the FEM is able to estimate solutions of Maxwell-s equations
governing the power transmission systems. The computer simulation
based on the use of the FEM has been developed in MATLAB
programming environment.
Abstract: Amarindra-vinitchai-mahaisuraya Bhiman throne hall
is one of the most significant throne halls in the grand palace in the
Ratthanakosin city situated in Bangkok, Thailand. This is the first
group of throne halls built in order to serve as a place for meetings,
performing state affairs and royal duties until the present time. The
structure and pattern of architectural design including the decoration
and interior design of the throne hall obviously exhibits and convey
the status of the king under the context of Thai society in the early
period of Ratthanakosin era. According to the tradition of ruling the
kingdom in absolute monarchy which had been in place since
Ayutthaya era (A.D.1350-1767), the king was deemed as Deva Raja,
the highest power and authority over the kingdom and as the greatest
emperor of the universe (Chakkravatin). The architectural design
adopted the concept of “Prasada" or Viman which served as the
dwelling place of the gods and was presented in the form of “Thai
traditional architecture" For the interior design of the throne hall, it
had been adopted to be the heaven and the centre of the Universe in
line with the cosmological beliefs of ancient people described in
scripture Tribhumikatha (Tri Bhumi) written by Phra Maha Thamma
Raja (Phraya Lithai) of the Sukhothai era (A.D.1347-1368).
According to this belief, the throne hall had been designed to represent
mount Meru, the central of the universe. On the top end of Mount
Meru is situated the Viman and dwelling place of Indra who is the king
of gods according to the idea of Deva Raja (the king god Avatar). At
the same time, Indra also existed as the king of the universe
simultaneously.
Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: The interline power flow controller (IPFC) is one of
the latest generation flexible AC transmission systems (FACTS)
controller used to control power flows of multiple transmission lines.
This paper presents a mathematical model of IPFC, termed as power
injection model (PIM). This model is incorporated in Newton-
Raphson (NR) power flow algorithm to study the power flow control
in transmission lines in which IPFC is placed. A program in
MATLAB has been written in order to extend conventional NR
algorithm based on this model. Numerical results are carried out on a
standard 2 machine 5 bus system. The results without and with IPFC
are compared in terms of voltages, active and reactive power flows to
demonstrate the performance of the IPFC model.
Abstract: This paper deals with the thermo-mechanical deformation behavior of shear deformable functionally graded ceramicmetal (FGM) plates. Theoretical formulations are based on higher order shear deformation theory with a considerable amendment in the transverse displacement using finite element method (FEM). The mechanical properties of the plate are assumed to be temperaturedependent and graded in the thickness direction according to a powerlaw distribution in terms of the volume fractions of the constituents. The temperature field is supposed to be a uniform distribution over the plate surface (XY plane) and varied in the thickness direction only. The fundamental equations for the FGM plates are obtained using variational approach by considering traction free boundary conditions on the top and bottom faces of the plate. A C0 continuous isoparametric Lagrangian finite element with thirteen degrees of freedom per node have been employed to accomplish the results. Convergence and comparison studies have been performed to demonstrate the efficiency of the present model. The numerical results are obtained for different thickness ratios, aspect ratios, volume fraction index and temperature rise with different loading and boundary conditions. Numerical results for the FGM plates are provided in dimensionless tabular and graphical forms. The results proclaim that the temperature field and the gradient in the material properties have significant role on the thermo-mechanical deformation behavior of the FGM plates.
Abstract: Kuwait-s electric power system is vertically integrated
organization owned and operated by the government. For more than
five decades, the government of Kuwait has provided relatively
reliable electric services to consumers with subsidized electric
service fees. Given the country-s rapid socio-economical
development and consequently the increase of electricity demand, a
question that inflicts itself: Is it necessary to reform the power system
to face the fast growing demand? This paper recommends that the
government should consider the private sector as a partner in
operating the power system. Therefore, power system restructuring is
needed to allow such partnership. There are challenges that prevent
such restructuring. Abstract recommendations toward resolving these
challenges are proposed.
Abstract: This paper presents the DC voltage control design of D-STATCOM when the D-STATCOM is used for load voltage regulation. Although, the DC voltage can be controlled by active current of the D-STATCOM, reactive current still affects the DC voltage. To eliminate this effect, the control strategy with elimination effect of the reactive current is proposed and the results of the control with and without the elimination the effect of the reactive current are compared. For obtaining the proportional and integral gains of the PI controllers, the symmetrical optimum and genetic algorithms methods are applied. The stability margin of these methods are obtained and discussed in detail. In addition, the performance of the DC voltage control based on symmetrical optimum and genetic algorithms methods are compared. Effectiveness of the controllers designed was verified through computer simulation performed by using Power System Tool Block (PSB) in SIMULINK/MATLAB. The simulation results demonstrated that the DC voltage control proposed is effective in regulating DC voltage when the DSTATCOM is used for load voltage regulation.
Abstract: The presented paper is related to the design methods and neutronic characterization of the reactivity control system in the large power unit of Generation IV Gas cooled Fast Reactor – GFR2400. The reactor core is based on carbide pin fuel type with the application of refractory metallic liners used to enhance the fission product retention of the SiCcladding. The heterogeneous design optimization of control rod is presented and the results of rods worth and their interferences in a core are evaluated. In addition, the idea of reflector removal as an additive reactivity management option is investigated and briefly described.
Abstract: Wireless sensor networks (WSNs) consist of number
of tiny, low cost and low power sensor nodes to monitor some physical phenomenon. The major limitation in these networks is the use of non-rechargeable battery having limited power supply. The
main cause of energy consumption in such networks is
communication subsystem. This paper presents an energy efficient
Cluster Cooperative Caching at Sensor (C3S) based upon grid type clustering. Sensor nodes belonging to the same cluster/grid form a
cooperative cache system for the node since the cost for
communication with them is low both in terms of energy
consumption and message exchanges. The proposed scheme uses
cache admission control and utility based data replacement policy to
ensure that more useful data is retained in the local cache of a node.
Simulation results demonstrate that C3S scheme performs better in
various performance metrics than NICoCa which is existing
cooperative caching protocol for WSNs.
Abstract: Wireless sensor network is formed with the combination of sensor nodes and sink nodes. Recently Wireless sensor network has attracted attention of the research community. The main application of wireless sensor network is security from different attacks both for mass public and military. However securing these networks, by itself is a critical issue due to many constraints like limited energy, computational power and lower memory. Researchers working in this area have proposed a number of security techniques for this purpose. Still, more work needs to be done.In this paper we provide a detailed discussion on security in wireless sensor networks. This paper will help to identify different obstacles and requirements for security of wireless sensor networks as well as highlight weaknesses of existing techniques.
Abstract: Recently, as the scale of construction projects has
increases, more ground excavation for foundations is carried out than ever before. Consequently, damage to underground ducts (gas, water/sewage or oil pipelines, communication cables or power cable ducts) or superannuated pipelines frequently cause serious accidents
resulting in damage to life and property. (In Korea, the total length of city water pipelines was approximately 2,000 km as of the end of 2009.) In addition, large amounts of damage caused by fractures, water
and gas leakage caused by superannuation or damage to underground
ducts in construction has been reported. Therefore, a system is required to precisely detect defects and deterioration in underground
pipelines and the locations of such defects, for timely and accurate
maintenance or replacement of the ducts. In this study, a system was
developed which can locate underground structures (gas and water
pipelines, power cable ducts, etc.) in 3D-coordinates and monitor the
degree and position of defects using an Inertial Measurement Unit
(IMU) sensing technique. The system can prevent damage to underground ducts and superannuated pipelines during construction,
and provide reliable data for maintenance. The utility of the IMU sensing technique used in aircraft and ships in civil applications was
verified.
Abstract: Fly ash is one of the residues generated in
combustion, and comprises the fine particles that rise with the flue
gases. Ash which does not rise is termed bottom ash [1]. In our
country, it is expected that will be occurred 50 million tons of waste
ash per year until 2020. Released waste from the thermal power
plants is caused very significant problems as known. The fly ashes
can be evaluated by using as adsorbent material.
The purpose of this study is to investigate the possibility of use of
Tuncbilek fly ash like low-cost adsorbents for heavy metal
adsorption. First of all, Tuncbilek fly ash was characterized. For this
purpose; analysis such as sieve analysis, XRD, XRF, SEM and FT-IR
were performed.