Abstract: In recent years there has been renewal of interest in the
relation between Green IT and Cloud Computing. The growing use of
computers in cloud platform has caused marked energy consumption,
putting negative pressure on electricity cost of cloud data center. This
paper proposes an effective mechanism to reduce energy utilization in
cloud computing environments. We present initial work on the
integration of resource and power management that aims at reducing
power consumption. Our mechanism relies on recalling virtualization
services dynamically according to user-s virtualization request and
temporarily shutting down the physical machines after finish in order
to conserve energy. Given the estimated energy consumption, this
proposed effort has the potential to positively impact power
consumption. The results from the experiment concluded that energy
indeed can be saved by powering off the idling physical machines in
cloud platforms.
Abstract: This paper presents the results of the preliminary investigation of microwave (MW) irradiation pretreatments on the anaerobic digestion of food residues using biochemical methane potential (BMP) assays. Low solids systems with a total solids (TS) content ranging from 5.0-10.0% were analyzed. The inoculum to bulk mass of substrates to water ratio was 1:2:2 (mass basis). The experimental conditions for pretreatments were as follows: a control (no MW irradiation), two runs with MW irradiation for 15 and 30 minutes at 320 W, and another two runs with MW irradiation at 528 W for 30 and 60 minutes. The cumulative biogas production were 6.3 L and 8.7 L for 15min/320 W and 30min/320 W MW irradiation conditions, respectively, and 10.5 L and 11.4 L biogas for 30min/528 W and 60min/528 W, respectively, as compared to the control giving 5.8 L biogas. Both an increase in exposure time of irradiation and power of MW had increased the rate and yield of biogas. Singlefactor ANOVA tests (p
Abstract: This paper presents the significant factor and give
some suggestion that should know before design. The main objective of this paper is guide the first step for someone who attends to design of grounding system before study in details later. The overview of
grounding system can protect damage from fault such as can save a human life and power system equipment. The unsafe conditions have
three cases. Case 1) maximum touch voltage exceeds the safety
criteria. In this case, the conductor compression ratio of the ground gird should be first adjusted to have optimal spacing of ground grid
conductors. If it still over limit, earth resistivity should be consider afterward. Case 2) maximum step voltage exceeds the safety criteria.
In this case, increasing the number of ground grid conductors around
the boundary can solve this problem. Case 3) both of maximum touch
and step voltage exceed the safety criteria. In this case, follow the solutions explained in case 1 and case 2. Another suggestion, vary depth of ground grid until maximum step and touch voltage do not
exceed the safety criteria.
Abstract: This paper presents a mathematical model and a
methodology to analyze the losses in transmission expansion
planning (TEP) under uncertainty in demand. The methodology is
based on discrete particle swarm optimization (DPSO). DPSO is a
useful and powerful stochastic evolutionary algorithm to solve the
large-scale, discrete and nonlinear optimization problems like TEP.
The effectiveness of the proposed idea is tested on an actual
transmission network of the Azerbaijan regional electric company,
Iran. The simulation results show that considering the losses even for
transmission expansion planning of a network with low load growth
is caused that operational costs decreases considerably and the
network satisfies the requirement of delivering electric power more
reliable to load centers.
Abstract: Finite impulse response (FIR) filters have the advantage of linear phase, guaranteed stability, fewer finite precision errors, and efficient implementation. In contrast, they have a major disadvantage of high order need (more coefficients) than IIR counterpart with comparable performance. The high order demand imposes more hardware requirements, arithmetic operations, area usage, and power consumption when designing and fabricating the filter. Therefore, minimizing or reducing these parameters, is a major goal or target in digital filter design task. This paper presents an algorithm proposed for modifying values and the number of non-zero coefficients used to represent the FIR digital pulse shaping filter response. With this algorithm, the FIR filter frequency and phase response can be represented with a minimum number of non-zero coefficients. Therefore, reducing the arithmetic complexity needed to get the filter output. Consequently, the system characteristic i.e. power consumption, area usage, and processing time are also reduced. The proposed algorithm is more powerful when integrated with multiplierless algorithms such as distributed arithmetic (DA) in designing high order digital FIR filters. Here the DA usage eliminates the need for multipliers when implementing the multiply and accumulate unit (MAC) and the proposed algorithm will reduce the number of adders and addition operations needed through the minimization of the non-zero values coefficients to get the filter output.
Abstract: As chip manufacturing technology is suddenly on the
threshold of major evaluation, which shrinks chip in size and
performance, LFSR (Linear Feedback Shift Register) is implemented
in layout level which develops the low power consumption chip,
using recent CMOS, sub-micrometer layout tools. Thus LFSR
counter can be a new trend setter in cryptography and is also
beneficial as compared to GRAY & BINARY counter and variety of
other applications.
This paper compares 3 architectures in terms of the hardware
implementation, CMOS layout and power consumption, using
Microwind CMOS layout tool. Thus it provides solution to a low
power architecture implementation of LFSR in CMOS VLSI.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: Multi-energy systems will enhance the system
reliability and power quality. This paper presents an integrated
approach for the design and operation of distributed energy resources
(DER) systems, based on energy hub modeling. A multi-objective
optimization model is developed by considering an integrated view of
electricity and natural gas network to analyze the optimal design and
operating condition of DER systems, by considering two conflicting
objectives, namely, minimization of total cost and the minimization
of environmental impact which is assessed in terms of CO2
emissions. The mathematical model considers energy demands of the
site, local climate data, and utility tariff structure, as well as technical
and financial characteristics of the candidate DER technologies. To
provide energy demands, energy systems including photovoltaic, and
co-generation systems, boiler, central power grid are considered. As
an illustrative example, a hotel in Iran demonstrates potential
applications of the proposed method. The results prove that
increasing the satisfaction degree of environmental objective leads to
increased total cost.
Abstract: Public awareness towards green energy are on the rise and this can be prove by many product being manufactured or prerequired to be made as energy saving devices mainly to save consumer from spending more on utility billing. These schemes are popular nowadays and many homemade appliances are turned into energy saving gadget which attracts the attention of consumers. Knowing the public demands and pattern towards purchasing home appliances thus the idea of “energy saving suction hood (ESSH)" is proposed. The ESSH can be used in many places that require smoke ventilation or even to reduce the room temperature as many conventional suction hoods (CSH) do, but this device works automatically by the usage of sensors that detects the smoke/temperature and automatically spins the exhaust fan. As it turns, the mechanical rotation rotates the AC generator which is coupled together with the fan and then charges the battery. The innovation of this product is, it does not rely on the utility supply as it is also hook up with a solar panel which also charges the battery, Secondly, it generates energy as the exhaust fan mechanically rotates. Thirdly, an energy loop back feature is introduced to this system which will supply for the ventilator fan. Another major innovation is towards interfacing this device with an in house production of generator. This generator is produced by proper design on stator as well as rotor to reduce the losses. A comparison is made between the ESSH and the CSH and result shows that the ESSH saves 172.8kWh/year of utility supply which is used by CSH. This amount of energy can save RM 3.14 from monthly utility bill and a total of RM 37.67 per year. In fact this product can generate 175 Watt of power from generator(75W) and solar panel(100W) that can be used either to supply other household appliances and/or to loop back to supply the fans motor. The innovation of this system is essential for future production of other equipment by using the loopback power method and turning most equipment into a standalone system.
Abstract: Static synchronous compensator (STATCOM) is a shunt connected voltage source converter (VSC), which can affect rapid control of reactive flow in the transmission line by controlling the generated a.c. voltage. The main aim of the paper is to design a power system installed with a Static synchronous compensator (STATCOM) and demonstrates the application of the linearised Phillips-heffron model in analyzing the damping effect of the STATCOM to improve power system oscillation stability. The proposed PI controller is designed to coordinate two control inputs: Voltage of the injection bus and capacitor voltage of the STATCOM, to improve the Dynamic stability of a SMIB system .The power oscillations damping (POD) control and power system stabilizer (PSS) and their coordinated action with proposed controllers are tested. The simulation result shows that the proposed damping controllers provide satisfactory performance in terms of improvements of dynamic stability of the system.
Abstract: This study aimed to evaluate regional soil Borkhar of
the metals Lead has been made. In this field study fires visits to the
regions. The limit of this study located in the East refineries,
petrochemical and power plant to 20 km was selected. The 41 soil
samples from depths of 0 to 10 cm in area and were randomized. Soil
samples were transported to the laboratory and by air was dry and
passed through 2-mil thickness sieve. In the laboratory of physical
and chemical characteristics and concentrations of total absorption
was measured. The results showed that the amount of lead in soil in
many parts of the range higher than the standard limit. Survey maps
show that the lead spatial distribution of the region does not special
pattern.
Abstract: This paper proposes a robot able to climb Columns.
This robot is not dependent on the diameter and material of the
columns. Some climbing robots have been designed up to now but
Koala robot was designed and fabricated for climbing columns
exclusively. Simple kinematics of climbing in the nature inspired us
to design this robot. We used two linear mechanisms to grip the
column. The gripper consists of a DC motor and a power screw
mechanism with a linear bushing as a guide. This mechanism
provides enough force to grip the column. In addition we needed an
actuator for climbing the column; hence, two pneumatic jacks were
used. All the mechanical parts were designed according to the
exerted forces and operational condition. The prototype can be
simply installed and controlled on the column by an inexperienced
operator. This robot is intended for inspection and surveillance of
pipes in oil industries and power poles in electric industries.
Abstract: This paper presents a new approach for setting
frequency relays based on the dynamic of power system. A
simplified model of the power system based on the load-frequency
control loop will be developed to be used instead of the complete
model of the power system. The effects of the equipments and their
responses on the frequency variations of the power plant will be
investigated and then a method for adaptive settings of frequency
relays will be explained. The proposed method will be investigated
by analyzing a simplified model of a power plant by MATLAB
software.
Abstract: In this paper we present a soft timing phase estimation (STPE) method for wireless mobile receivers operating in low signal to noise ratios (SNRs). Discrete Polyphase Matched (DPM) filters, a Log-maximum a posterior probability (MAP) and/or a Soft-output Viterbi algorithm (SOVA) are combined to derive a new timing recovery (TR) scheme. We apply this scheme to wireless cellular communication system model that comprises of a raised cosine filter (RCF), a bit-interleaved turbo-coded multi-level modulation (BITMM) scheme and the channel is assumed to be memory-less. Furthermore, no clock signals are transmitted to the receiver contrary to the classical data aided (DA) models. This new model ensures that both the bandwidth and power of the communication system is conserved. However, the computational complexity of ideal turbo synchronization is increased by 50%. Several simulation tests on bit error rate (BER) and block error rate (BLER) versus low SNR reveal that the proposed iterative soft timing recovery (ISTR) scheme outperforms the conventional schemes.
Abstract: The scientific perspective, the practice area of physical education and sports activities improve power capacity in all its forms of expression, being a generator of the research topics. Today theories that strength training athletes and slow down development progress will affect the strength and flexibility are discredited. On the other hand there are sectors and / or samples whose results are sports of the way higher manifestation of power as a result of the composition of the force and velocity, being based in this respect on the systematic and continuous development of both bio-motric capacities said. Training of force for children was and is controversial. Teama de accidentări sau a stopării premature a procesului de creştere a făcut ca în trecut copiii să fie ţinuţi departe de lucrul cu diferite greutăţi.Fear of injury or premature stop the growth process in the past made the children to be kept away from working with different weights. Recent studies have shown that the risk of accidents is relatively small and the strength training can help prevent them. For example, most accidents occur at the level of athletics ligaments and tendons. From this point of view, it can be said that a progressive intervention of force training, optimal design, will help enhancing their process, such as athlete much better prepared to meet training requests and competitions. Preparation of force provides a solid basis for further phases in the highest performance.
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: Short circuit currents plays a vital role in influencing the design and operation of equipment and power system and could not be avoided despite careful planning and design, good maintenance and thorough operation of the system. This paper discusses the short circuit analysis conducted in KSO briefly comprising of its significances, methods and results. A result sample of the analysis based on a single transformer is detailed in this paper. Furthermore, the results of the analysis and its significances were also discussed and commented.
Abstract: With the advantage of wireless network technology,
there are a variety of mobile applications which make the issue of
wireless sensor networks as a popular research area in recent years.
As the wireless sensor network nodes move arbitrarily with the
topology fast change feature, mobile nodes are often confronted with
the void issue which will initiate packet losing, retransmitting,
rerouting, additional transmission cost and power consumption.
When transmitting packets, we would not predict void problem
occurring in advance. Thus, how to improve geographic routing with
void avoidance in wireless networks becomes an important issue. In
this paper, we proposed a greedy geographical void routing algorithm
to solve the void problem for wireless sensor networks. We use the
information of source node and void area to draw two tangents to
form a fan range of the existence void which can announce voidavoiding
message. Then we use source and destination nodes to draw
a line with an angle of the fan range to select the next forwarding
neighbor node for routing. In a dynamic wireless sensor network
environment, the proposed greedy void avoiding algorithm can be
more time-saving and more efficient to forward packets, and improve
current geographical void problem of wireless sensor networks.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: With data centers, end-users can realize the pervasiveness of services that will be one day the cornerstone of our lives. However, data centers are often classified as computing systems that consume the most amounts of power. To circumvent such a problem, we propose a self-adaptive weighted sum methodology that jointly optimizes the performance and power consumption of any given data center. Compared to traditional methodologies for multi-objective optimization problems, the proposed self-adaptive weighted sum technique does not rely on a systematical change of weights during the optimization procedure. The proposed technique is compared with the greedy and LR heuristics for large-scale problems, and the optimal solution for small-scale problems implemented in LINDO. the experimental results revealed that the proposed selfadaptive weighted sum technique outperforms both of the heuristics and projects a competitive performance compared to the optimal solution.