Abstract: Recently hybrid vehicles have become a major concern as one alternative vehicles. This type of hybrid vehicle contributes greatly to reducing pollution. Therefore, this work studies the influence of electrification phase of hybrid electric vehicle on emission of vehicle at different road conditions. To accomplish this investigation, a simulation model was used to evaluate the external characteristics of the hybrid electric vehicle according to variant conditions of road resistances. Therefore, this paper reports a methodology to decrease the vehicle emission especially greenhouse gas emission inside cities. The results show the effect of electrification on vehicle performance characteristics. The results show that CO2 emission of vehicle decreases up to 50.6% according to an urban driving cycle due to applying the electrification strategy for hybrid electric vehicle.
Abstract: Different countries have introduced different schemes
and policies to counter global warming. The rationale behind the
proposed policies and the potential barriers to successful
implementation of the policies adopted by the countries were
analyzed and estimated based on different models. It is argued that
these models enhance the transparency and provide a better
understanding to the policy makers. However, these models are
underpinned with several structural and baseline assumptions. These
assumptions, modeling features and future prediction of emission
reductions and other implication such as cost and benefits of a
transition to a low-carbon economy and its economy wide impacts
were discussed. On the other hand, there are potential barriers in the
form political, financial, and cultural and many others that pose a
threat to the mitigation options.
Abstract: In most existing buildings in hot climate, cooling
loads lead to high primary energy consumption and consequently
high CO2 emissions. These can be substantially decreased with
integrated renewable energy systems. Kuwait is characterized by its
dry hot long summer and short warm winter. Kuwait receives annual
total radiation more than 5280 MJ/m2 with approximately 3347 h of
sunshine. Solar energy systems consist of PV modules and parabolic
trough collectors are considered to satisfy electricity consumption,
domestic water heating, and cooling loads of an existing building.
This paper presents the results of an extensive program of energy
conservation and energy generation using integrated photovoltaic
(PV) modules and Parabolic Trough Collectors (PTC). The program
conducted on an existing institutional building intending to convert it
into a Net-Zero Energy Building (NZEB) or near net Zero Energy
Building (nNZEB). The program consists of two phases; the first
phase is concerned with energy auditing and energy conservation
measures at minimum cost and the second phase considers the
installation of photovoltaic modules and parabolic trough collectors.
The 2-storey building under consideration is the Applied Sciences
Department at the College of Technological Studies, Kuwait. Single
effect lithium bromide water absorption chillers are implemented to
provide air conditioning load to the building. A numerical model is
developed to evaluate the performance of parabolic trough collectors
in Kuwait climate. Transient simulation program (TRNSYS) is
adapted to simulate the performance of different solar system
components. In addition, a numerical model is developed to assess
the environmental impacts of building integrated renewable energy
systems. Results indicate that efficient energy conservation can play
an important role in converting the existing buildings into NZEBs as
it saves a significant portion of annual energy consumption of the
building. The first phase results in an energy conservation of about
28% of the building consumption. In the second phase, the integrated
PV completely covers the lighting and equipment loads of the
building. On the other hand, parabolic trough collectors of optimum
area of 765 m2 can satisfy a significant portion of the cooling load,
i.e about73% of the total building cooling load. The annual avoided
CO2 emission is evaluated at the optimum conditions to assess the
environmental impacts of renewable energy systems. The total annual
avoided CO2 emission is about 680 metric ton/year which confirms
the environmental impacts of these systems in Kuwait.
Abstract: This paper presents a detailed description of evaporative cooling systems used for space cooling in Mina Valley, Saudi Arabia. The thermal performance and environmental impact of the evaporative coolers were evaluated. It was found that the evaporative cooling systems used for space cooling in pilgrims’ accommodations and in the train stations could reduce energy consumption by as much as 75% and cut carbon dioxide emission by 78% compared to traditional vapour compression systems.
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.
Abstract: Multi-energy systems will enhance the system
reliability and power quality. This paper presents an integrated
approach for the design and operation of distributed energy resources
(DER) systems, based on energy hub modeling. A multi-objective
optimization model is developed by considering an integrated view of
electricity and natural gas network to analyze the optimal design and
operating condition of DER systems, by considering two conflicting
objectives, namely, minimization of total cost and the minimization
of environmental impact which is assessed in terms of CO2
emissions. The mathematical model considers energy demands of the
site, local climate data, and utility tariff structure, as well as technical
and financial characteristics of the candidate DER technologies. To
provide energy demands, energy systems including photovoltaic, and
co-generation systems, boiler, central power grid are considered. As
an illustrative example, a hotel in Iran demonstrates potential
applications of the proposed method. The results prove that
increasing the satisfaction degree of environmental objective leads to
increased total cost.
Abstract: Over 90% of the world trade is carried by the
international shipping industry. As most of the countries are
developing, seaborne trade continues to expand to bring benefits for
consumers across the world. Studies show that world trade will
increase 70-80% through shipping in the next 15-20 years. Present
global fleet of 70000 commercial ships consumes approximately 200
million tonnes of diesel fuel a year and it is expected that it will be
around 350 million tonnes a year by 2020. It will increase the
demand for fuel and also increase the concentration of CO2 in the
atmosphere. So, it-s essential to control this massive fuel
consumption and CO2 emission. The idea is to utilize a diesel-wind
hybrid system for ship propulsion. Use of wind energy by installing
modern wing-sails in ships can drastically reduce the consumption of
diesel fuel. A huge amount of wind energy is available in oceans.
Whenever wind is available the wing-sails would be deployed and
the diesel engine would be throttled down and still the same forward
speed would be maintained. Wind direction in a particular shipping
route is not same throughout; it changes depending upon the global
wind pattern which depends on the latitude. So, the wing-sail
orientation should be such that it optimizes the use of wind energy.
We have made a computer programme in which by feeding the data
regarding wind velocity, wind direction, ship-motion direction; we
can find out the best wing-sail position and fuel saving for
commercial ships. We have calculated net fuel saving in certain
international shipping routes, for instance, from Mumbai in India to
Durban in South Africa. Our estimates show that about 8.3% diesel
fuel can be saved by utilizing the wind. We are also developing an
experimental model of the ship employing airfoils (small scale wingsail)
and going to test it in National Wind Tunnel Facility in IIT
Kanpur in order to develop a control mechanism for a system of
airfoils.