Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: In this paper, an alternating implicit block method for
solving two dimensional scalar wave equation is presented. The
new method consist of two stages for each time step implemented
in alternating directions which are very simple in computation. To
increase the speed of computation, a group of adjacent points is
computed simultaneously. It is shown that the presented method
increase the maximum time step size and more accurate than the
conventional finite difference time domain (FDTD) method and other
existing method of natural ordering.
Abstract: Using maximal consistent blocks of tolerance relation
on the universe in incomplete decision table, the concepts of join block
and meet block are introduced and studied. Including tolerance class,
other blocks such as tolerant kernel and compatible kernel of an object
are also discussed at the same time. Upper and lower approximations
based on those blocks are also defined. Default definite decision rules
acquired from incomplete decision table are proposed in the paper. An
incremental algorithm to update default definite decision rules is
suggested for effective mining tasks from incomplete decision table
into which data is appended. Through an example, we demonstrate
how default definite decision rules based on maximal consistent
blocks, join blocks and meet blocks are acquired and how optimization
is done in support of discernibility matrix and discernibility function
in the incomplete decision table.
Abstract: Due to the excess of a vehicle operation through its life, some elements may face failure and deteriorate with time. This leads us to carry out maintenance, repair, tune up or full overhaul. After a certain period, the vehicle elements deteriorations increase with time which causes a very high increase of doing the maintenance operations and their costs. However, the logic decision at this point is to replace the current vehicle by a new one with minimum failure and maximum income. The importance of studying vehicle replacement problems come from the increase of stopping days due to many deteriorations in the vehicle parts. These deteriorations increase year after year causing an increase of operating costs and decrease the vehicle income. Vehicle replacement aims to determine the optimum time to keep, maintain, overhaul, renew and replace vehicles. This leads to an improvement in vehicle income, total operating costs, maintenance cost, fuel and oil costs, ton-kilometers, vehicle and engine performance, vehicle noise, vibration, and pollution. The aim of this paper is to find the optimum replacement policies of Kuwait Passenger Transport Company (KPTCP) fleet of busses. The objective of these policies is to maximize the busses pure profits. The dynamic programming (D.P.) technique is used to generate the busses optimal replacement policies
Abstract: The solution algorithm, based on Lagrangian relaxation, a sub-gradient method and a heuristic to find the upper bound of the solution, is proposed to solve the coordinated fleet routing and flight scheduling problems. Numerical tests are performed to evaluate the proposed algorithm using real operating data from two Taiwan airlines. The test results indicate that the solution algorithm is a significant improvement over those obtained with CPLEX, consequently they could be useful for allied airlines to solve coordinated fleet routing and flight scheduling problems.
Abstract: In this work, biohydrogen production via dark
fermentation from alcohol wastewater using upflow anaerobic sludge
blanket reactors (UASB) with a working volume of 4 L was
investigated to find the optimum conditions for a maximum hydrogen
yield. The system was operated at different COD loading rates (23,
31, 46 and 62 kg/m3d) at mesophilic temperature (37 ºC) and pH 5.5.
The seed sludge was pretreated before being fed to the UASB system
by boiling at 95 ºC for 15 min. When the system was operated under
the optimum COD loading rate of 46 kg/m3d, it provided the
hydrogen content of 27%, hydrogen yield of 125.1 ml H2/g COD
removed and 95.1 ml H2/g COD applied, hydrogen production rate of
18 l/d, specific hydrogen production rate of 1080 ml H2/g MLVSS d
and 1430 ml H2/ L d, and COD removal of 24%.
Abstract: Mobile Ad Hoc Networks (MANETs) are multi-hop
wireless networks in which all nodes cooperatively maintain network
connectivity. In such a multi-hop wireless network, every node may
be required to perform routing in order to achieve end-to-end
communication among nodes. These networks are energy constrained
as most ad hoc mobile nodes today operate with limited battery
power. Hence, it is important to minimize the energy consumption of
the entire network in order to maximize the lifetime of ad hoc
networks. In this paper, a mechanism involving the integration of
load balancing approach and transmission power control approach is
introduced to maximize the life-span of MANETs. The mechanism is
applied on Ad hoc On-demand Vector (AODV) protocol to make it
as energy aware AODV (EA_AODV). The simulation is carried out
using GloMoSim2.03 simulator. The results show that the proposed
mechanism reduces the average required transmission energy per
packet compared to the standard AODV.
Abstract: This Paper presents a particle swarm optimization (PSO) method for determining the optimal proportional-integral-derivative (PID) controller parameters, for speed control of a linear brushless DC motor. The proposed approach has superior features, including easy implementation, stable convergence characteristic and good computational efficiency. The brushless DC motor is modelled in Simulink and the PSO algorithm is implemented in MATLAB. Comparing with Genetic Algorithm (GA) and Linear quadratic regulator (LQR) method, the proposed method was more efficient in improving the step response characteristics such as, reducing the steady-states error; rise time, settling time and maximum overshoot in speed control of a linear brushless DC motor.
Abstract: The flow filed around a flatted-roof compound has
been investigated by means of 2D and 3D numerical simulations. A
constant wind velocity profile, based both on the maximum reference
wind speed in the building site (peak gust speed worked out for a 50-
year return period) and on the local roughness coefficient, has been
simulated in order to determine the wind-induced loads on top of the
roof. After determining the influence of the incoming wind directions
on the induced roof loads, a 2D analysis of the most severe load
condition has been performed, achieving a numerical quantification
of the expected wind-induced forces on the PV panels on top of the
roof.
Abstract: A considerable amount of energy is consumed during
transmission and reception of messages in a wireless mesh network
(WMN). Reducing per-node transmission power would greatly
increase the network lifetime via power conservation in addition to
increasing the network capacity via better spatial bandwidth reuse. In
this work, the problem of topology control in a hybrid WMN of
heterogeneous wireless devices with varying maximum transmission
ranges is considered. A localized distributed topology control
algorithm is presented which calculates the optimal transmission
power so that (1) network connectivity is maintained (2) node
transmission power is reduced to cover only the nearest neighbours
(3) networks lifetime is extended. Simulations and analysis of results
are carried out in the NS-2 environment to demonstrate the
correctness and effectiveness of the proposed algorithm.
Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: Determining how many virtual machines a Linux host
could run can be a challenge. One of tough missions is to find the
balance among performance, density and usability. Now KVM
hypervisor has become the most popular open source full
virtualization solution. It supports several ways of running guests with
more memory than host really has. Due to large differences between
minimum and maximum guest memory requirements, this paper
presents initial results on same-page merging, ballooning and live
migration techniques that aims at optimum memory usage on
KVM-based cloud platform. Given the design of initial experiments,
the results data is worth reference for system administrators. The
results from these experiments concluded that each method offers
different reliability tradeoff.
Abstract: In this paper, we propose a new method to distinguish
between arousal and relaxation states by using multiple features
acquired from a photoplethysmogram (PPG) and support vector
machine (SVM). To induce arousal and relaxation states in subjects, 2
kinds of sound stimuli are used, and their corresponding biosignals are
obtained using the PPG sensor. Two features–pulse to pulse interval
(PPI) and pulse amplitude (PA)–are extracted from acquired PPG
data, and a nonlinear classification between arousal and relaxation is
performed using SVM.
This methodology has several advantages when compared with
previous similar studies. Firstly, we extracted 2 separate features from
PPG, i.e., PPI and PA. Secondly, in order to improve the classification
accuracy, SVM-based nonlinear classification was performed.
Thirdly, to solve classification problems caused by generalized
features of whole subjects, we defined each threshold according to
individual features.
Experimental results showed that the average classification
accuracy was 74.67%. Also, the proposed method showed the better
identification performance than the single feature based methods.
From this result, we confirmed that arousal and relaxation can be
classified using SVM and PPG features.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: A simple analytical model has been developed to
optimize biasing conditions for obtaining maximum linearity among
lattice-matched, pseudomorphic and metamorphic HEMT types as
well as enhancement and depletion HEMT modes. A nonlinear
current-voltage model has been simulated based on extracted data to
study and select the most appropriate type and mode of HEMT in
terms of a given gate-source biasing voltage within the device so as
to employ the circuit for the highest possible output current or
voltage linear swing. Simulation results can be used as a basis for the
selection of optimum gate-source biasing voltage for a given type
and mode of HEMT with regard to a circuit design. The
consequences can also be a criterion for choosing the optimum type
or mode of HEMT for a predetermined biasing condition.
Abstract: This paper presents a method of reducing the feedback
delay time of DWA(Data Weighted Averaging) used in sigma-delta
modulators. The delay time reduction results from the elimination of
the latch at the quantizer output and also from the falling edge
operation. The designed sigma-delta modulator improves the timing
margin about 16%. The sub-circuits of sigma-delta modulator such as
SC(Switched Capacitor) integrator, 9-level quantizer, comparator, and
DWA are designed with the non-ideal characteristics taken into
account. The sigma-delta modulator has a maximum SNR (Signal to
Noise Ratio) of 84 dB or 13 bit resolution.
Abstract: Com Poisson distribution is capable of modeling the count responses irrespective of their mean variance relation and the parameters of this distribution when fitted to a simple cross sectional data can be efficiently estimated using maximum likelihood (ML) method. In the regression setup, however, ML estimation of the parameters of the Com Poisson based generalized linear model is computationally intensive. In this paper, we propose to use quasilikelihood (QL) approach to estimate the effect of the covariates on the Com Poisson counts and investigate the performance of this method with respect to the ML method. QL estimates are consistent and almost as efficient as ML estimates. The simulation studies show that the efficiency loss in the estimation of all the parameters using QL approach as compared to ML approach is quite negligible, whereas QL approach is lesser involving than ML approach.
Abstract: The kinetic properties of enzymes are often reported
using the apparent KM and Vmax appropriate to the standard
Michaelis-Menten enzyme. However, this model is inappropriate to
enzymes that have more than one substrate or where the rate
expression does not apply for other reasons. Consequently, it is
desirable to have a means of estimating the appropriate kinetic
parameters from the apparent values of KM and Vmax reported for each
substrate. We provide a means of estimating the range within which
the parameters should lie and apply the method to data for glutamate
dehydrogenase from the nematode parasite of sheep Teladorsagia
circumcincta.
Abstract: Smoke discharging is a main reason of air pollution
problem from industrial plants. The obstacle of a building has an
affect with the air pollutant discharge. In this research, a mathematical
model of the smoke dispersion from two sources and one source with
a structural obstacle is considered. The governing equation of the
model is an isothermal mass transfer model in a viscous fluid. The
finite element method is used to approximate the solutions of the
model. The triangular linear elements have been used for discretising
the domain, and time integration has been carried out by semi-implicit
finite difference method. The simulations of smoke dispersion in
cases of one chimney and two chimneys are presented. The maximum
calculated smoke concentration of both cases are compared. It is then
used to make the decision for smoke discharging and air pollutant
control problems on industrial area.
Abstract: We present here the results for a comparative study of
some techniques, available in the literature, related to the relevance
feedback mechanism in the case of a short-term learning. Only one
method among those considered here is belonging to the data mining
field which is the K-nearest neighbors algorithm (KNN) while the
rest of the methods is related purely to the information retrieval field
and they fall under the purview of the following three major axes:
Shifting query, Feature Weighting and the optimization of the
parameters of similarity metric. As a contribution, and in addition to
the comparative purpose, we propose a new version of the KNN
algorithm referred to as an incremental KNN which is distinct from
the original version in the sense that besides the influence of the
seeds, the rate of the actual target image is influenced also by the
images already rated. The results presented here have been obtained
after experiments conducted on the Wang database for one iteration
and utilizing color moments on the RGB space. This compact
descriptor, Color Moments, is adequate for the efficiency purposes
needed in the case of interactive systems. The results obtained allow
us to claim that the proposed algorithm proves good results; it even
outperforms a wide range of techniques available in the literature.