Abstract: The pressure drag from a cam shaped tube in cross flows have been investigated experimentally using pressure distribution measurement. The range of angle of attack and Reynolds number based on an equivalent circular tube are within 0≤α≤360° and 2×104< Reeq < 3.4 ×104, respectively. It is found that the pressure drag coefficient is at its highest at α=90° and 270° over the whole range of Reynolds number. Results show that the pressure drag coefficient of the cam shaped tube is lower than that of circular tube with the same surface area for more of the angles of attack. Furthermore, effects of the diameter ratio and finite length of the cam shaped tube upon the pressure drag coefficient are discussed.
Abstract: Analytical investigation of the free vibration behavior
of circular functionally graded (FG) plates integrated with two
uniformly distributed actuator layers made of piezoelectric (PZT4)
material on the top and bottom surfaces of the circular FG plate
based on the classical plate theory (CPT) is presented in this paper.
The material properties of the functionally graded substrate plate are
assumed to be graded in the thickness direction according to the
power-law distribution in terms of the volume fractions of the
constituents and the distribution of electric potential field along the
thickness direction of piezoelectric layers is simulated by a quadratic
function. The differential equations of motion are solved analytically
for clamped edge boundary condition of the plate. The detailed
mathematical derivations are presented and Numerical investigations
are performed for FG plates with two surface-bonded piezoelectric
layers. Emphasis is placed on investigating the effect of varying the
gradient index of FG plate on the free vibration characteristics of the
structure. The results are verified by those obtained from threedimensional
finite element analyses.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: Attitude Determination (AD) of a spacecraft using the
phase measurements of the Global Navigation Satellite System
(GNSS) is an active area of research. Various attitude determination
algorithms have been developed in yester years for spacecrafts using
different sensors but the last two decades have witnessed a
phenomenal increase in research related with GPS receivers as a
stand-alone sensor for determining the attitude of satellite using the
phase measurements of the signals from GNSS. The GNSS-based
Attitude determination algorithms have been experimented in many
real missions. The problem of AD algorithms using GNSS phase
measurements has two important parts; the ambiguity resolution and
the determining of attitude. Ambiguity resolution is the widely
addressed topic in literature for implementing the AD algorithm
using GNSS phase measurements for achieving the accuracy of
millimeter level. This paper broadly overviews the different
techniques for resolving the integer ambiguities encountered in AD
using GNSS phase measurements.
Abstract: The objective of the present investigation was to
evaluate the morphology of Escherchia coli bacteria in interaction
with SiO2 nanoparticles.
This study was made by atomic force microscopy and quartz
crystal microbalance using SiO2 nanoparticles with 10nm, 50nm and
100nm diameter and bacteria immobilized on polyelectrolyte
multilayer films obtained by spin coating or by “layer by layer”
(LbL) method.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: Optimal load shedding (LS) design as an emergency plan is one of the main control challenges posed by emerging new uncertainties and numerous distributed generators including renewable energy sources in a modern power system. This paper presents an overview of the key issues and new challenges on optimal LS synthesis concerning the integration of wind turbine units into the power systems. Following a brief survey on the existing LS methods, the impact of power fluctuation produced by wind powers on system frequency and voltage performance is presented. The most LS schemas proposed so far used voltage or frequency parameter via under-frequency or under-voltage LS schemes. Here, the necessity of considering both voltage and frequency indices to achieve a more effective and comprehensive LS strategy is emphasized. Then it is clarified that this problem will be more dominated in the presence of wind turbines.
Abstract: The quality of Ribbed Smoked Sheets
(RSS) primarily based on color, dryness, and the presence or
absence of fungus and bubbles. This quality is strongly
influenced by the drying and fumigation process namely
smoking process. Smoking that is held in high temperature
long time will result scorched dark brown sheets, whereas if
the temperature is too low or slow drying rate would resulted
in less mature sheets and growth of fungus. Therefore need to
find the time and temperature for optimum quality of sheets.
Enhance, unmonitored heat and mass transfer during smoking
process lead to high losses of energy balance. This research
aims to generate simple empirical mathematical model
describing the effect of smoking time and temperature to RSS
quality of color, water content, fungus and bubbles. The
second goal of study was to analyze energy balance during
smoking process. Experimental study was conducted by
measuring temperature, residence time and quality parameters
of 16 sheets sample in smoking rooms. Data for energy
consumption balance such as mass of fuel wood, mass of
sheets being smoked, construction temperature, ambient
temperature and relative humidity were taken directly along
the smoking process. It was found that mathematical model
correlating smoking temperature and time with color is Color
= -169 - 0.184 T4 - 0.193 T3 - 0.160 0.405 T1 + T2 + 0.388 t1
+3.11 t2 + 3.92t3 + 0.215 t4 with R square 50.8% and with
moisture is Moisture = -1.40-0.00123 T4 + 0.00032 T3 +
0.00260 T2 - 0.00292 T1 - 0.0105 t1 + 0.0290 t2 + 0.0452 t3
+ 0.00061 t4 with R square of 49.9%. Smoking room energy
analysis found useful energy was 27.8%. The energy stored in
the material construction 7.3%. Lost of energy in conversion
of wood combustion, ventilation and others were 16.6%. The
energy flowed out through the contact of material construction
with the ambient air was found to be the highest contribution
to energy losses, it reached 48.3%.
Abstract: The normalized difference vegetation index (NDVI)
and normalized difference moisture index (NDMI) derived from the
moderate resolution imaging spectroradiometer (MODIS) have been
widely used to identify spatial information of drought condition. The
relationship between NDVI and NDMI has been analyzed using
Pearson correlation analysis and showed strong positive relationship.
The drought indices have detected drought conditions and identified
spatial extents of drought. A comparison between normal year and
drought year demonstrates that the amplitude analysis considered both
vegetation and moisture condition is an effective method to identify
drought condition. We proposed the amplitude analysis is useful for
quick spatial assessment of drought information at a regional scale.
Abstract: In this paper, we are concerned with the design and
its simulation studies of a modified extremum seeking control for
nonlinear systems. A standard extremum seeking control has a simple
structure, but it takes a long time to reach an optimal operating point.
We consider a modification of the standard extremum seeking control
which is aimed to reach the optimal operating point more speedily
than the standard one. In the modification, PD acceleration term
is added before an integrator making a principal control, so that it
enables the objects to be regulated to the optimal point smoothly. This
proposed method is applied to Monod and Williams-Otto models to
investigate its effectiveness. Numerical simulation results show that
this modified method can improve the time response to the optimal
operating point more speedily than the standard one.
Abstract: Aurein 1.2 is a 13-residue amphipathic peptide with antibacterial and anticancer activity. Aurein1.2 and its retro analog were synthesized to study the activity of the peptides in relation to their structure. The antibacterial test result showed the retro-analog is inactive. The secondary structural analysis by CD spectra indicated that both of the peptides at TFE/Water adopt alpha-helical conformation. MD simulation was performed on aurein 1.2 and retro-analog in water and TFE in order to analyse the factors that are involved in the activity difference between retro and the native peptide. The simulation results are discussed and validated in the light of experimental data from the CD experiment. Both of the peptides showed a relatively similar pattern for their hydrophobicity, hydrophilicity, solvent accessible surfaces, and solvent accessible hydrophobic surfaces. However, they showed different in directions of dipole moment of peptides. Also, Our results further indicate that the reversion of the amino acid sequence affects flexibility .The data also showed that factors causing structural rigidity may decrease the activity. Consequently, our finding suggests that in the case of sequence-reversed peptide strategy, one has to pay attention to the role of amino acid sequence order in making flexibility and role of dipole moment direction in peptide activity. KeywordsAntimicrobial peptides, retro, molecular dynamic, circular dichroism.
Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.
Abstract: A new deployment of the multiple criteria decision
making (MCDM) techniques: the Simple Additive Weighting
(SAW), and the Technique for Order Preference by Similarity to
Ideal Solution (TOPSIS) for portfolio allocation, is demonstrated in
this paper. Rather than exclusive reference to mean and variance as in
the traditional mean-variance method, the criteria used in this
demonstration are the first four moments of the portfolio distribution.
Each asset is evaluated based on its marginal impacts to portfolio
higher moments that are characterized by trapezoidal fuzzy numbers.
Then centroid-based defuzzification is applied to convert fuzzy
numbers to the crisp numbers by which SAW and TOPSIS can be
deployed. Experimental results suggest the similar efficiency of these
MCDM approaches to selecting dominant assets for an optimal
portfolio under higher moments. The proposed approaches allow
investors flexibly adjust their risk preferences regarding higher
moments via different schemes adapting to various (from
conservative to risky) kinds of investors. The other significant
advantage is that, compared to the mean-variance analysis, the
portfolio weights obtained by SAW and TOPSIS are consistently
well-diversified.
Abstract: In this paper, at first we explain about negative
hypergeometric distribution and its properties. Then we use the w-function
and the Stein identity to give a result on the poisson
approximation to the negative hypergeometric distribution in terms of the total variation distance between the negative hypergeometric and
poisson distributions and its upper bound.
Abstract: In this paper, we give the generalized alternating twostage method in which the inner iterations are accomplished by a generalized alternating method. And we present convergence results of the method for solving nonsingular linear systems when the coefficient matrix of the linear system is a monotone matrix or an H-matrix.
Abstract: A person-to-person information sharing is easily realized
by P2P networks in which servers are not essential. Leakage
of information, which are caused by malicious accesses for P2P
networks, has become a new social issues. To prevent information
leakage, it is necessary to detect and block traffics of P2P software.
Since some P2P softwares can spoof port numbers, it is difficult to
detect the traffics sent from P2P softwares by using port numbers.
It is more difficult to devise effective countermeasures for detecting
the software because their protocol are not public.
In this paper, a discriminating method of network applications
based on communication characteristics of application messages
without port numbers is proposed. The proposed method is based
on an assumption that there can be some rules about time intervals
to transmit messages in application layer and the number of necessary
packets to send one message. By extracting the rule from network
traffic, the proposed method can discriminate applications without
port numbers.
Abstract: This research was conducted in the Pua Watershed whereas located in the Upper Nan River Basin in Nan province, Thailand. Nan River basin originated in Nan province that comprises of many tributary streams to produce as inflow to the Sirikit dam provided huge reservoir with the storage capacity of 9510 million cubic meters. The common problems of most watersheds were found i.e. shortage water supply for consumption and agriculture utilizations, deteriorate of water quality, flood and landslide including debris flow, and unstable of riverbank. The Pua Watershed is one of several small river basins that flow through the Nan River Basin. The watershed includes 404 km2 representing the Pua District, the Upper Nan Basin, or the whole Nan River Basin, of 61.5%, 18.2% or 1.2% respectively. The Pua River is a main stream producing all year streamflow supplying the Pua District and an inflow to the Upper Nan Basin. Its length approximately 56.3 kilometers with an average slope of the channel by 1.9% measured. A diversion weir namely Pua weir bound the plain and mountainous areas with a very steep slope of the riverbed to 2.9% and drainage area of 149 km2 as upstream watershed while a mild slope of the riverbed to 0.2% found in a river reach of 20.3 km downstream of this weir, which considered as a gauged basin. However, the major branch streams of the Pua River are ungauged catchments namely: Nam Kwang and Nam Koon with the drainage area of 86 and 35 km2 respectively. These upstream watersheds produce runoff through the 3-streams downstream of Pua weir, Jao weir, and Kang weir, with an averaged annual runoff of 578 million cubic meters. They were analyzed using both statistical data at Pua weir and simulated data resulted from the hydrologic modeling system (HEC–HMS) which applied for the remaining ungauged basins. Since the Kwang and Koon catchments were limited with lack of hydrological data included streamflow and rainfall. Therefore, the mathematical modeling: HEC-HMS with the Snyder-s hydrograph synthesized and transposed methods were applied for those areas using calibrated hydrological parameters from the upstream of Pua weir with continuously daily recorded of streamflow and rainfall data during 2008-2011. The results showed that the simulated daily streamflow and sum up as annual runoff in 2008, 2010, and 2011 were fitted with observed annual runoff at Pua weir using the simple linear regression with the satisfied correlation R2 of 0.64, 062, and 0.59, respectively. The sensitivity of simulation results were come from difficulty using calibrated parameters i.e. lag-time, coefficient of peak flow, initial losses, uniform loss rates, and missing some daily observed data. These calibrated parameters were used to apply for the other 2-ungauged catchments and downstream catchments simulated.
Abstract: The purpose of the research was to determine
effectiveness of habilitation of preschool children with cerebral palsy
in the process of pedagogical support of their families. The author
presents the study of psychology-pedagogical problems of families
with preschool children with cerebral palsy and the universal
program of pedagogical support of families. In the conclusion, the
author determines effectiveness of social adaptation of children with
cerebral palsy and their families.
Abstract: Multi-user interference (MUI) is the main reason of system deterioration in the Spectral Amplitude Coding Optical Code Division Multiple Access (SAC-OCDMA) system. MUI increases with the number of simultaneous users, resulting into higher probability bit rate and limits the maximum number of simultaneous users. On the other hand, Phase induced intensity noise (PIIN) problem which is originated from spontaneous emission of broad band source from MUI severely limits the system performance should be addressed as well. Since the MUI is caused by the interference of simultaneous users, reducing the MUI value as small as possible is desirable. In this paper, an extensive study for the system performance specified by MUI and PIIN reducing is examined. Vectors Combinatorial (VC) codes families are adopted as a signature sequence for the performance analysis and a comparison with reported codes is performed. The results show that, when the received power increases, the PIIN noise for all the codes increases linearly. The results also show that the effect of PIIN can be minimized by increasing the code weight leads to preserve adequate signal to noise ratio over bit error probability. A comparison study between the proposed code and the existing codes such as Modified frequency hopping (MFH), Modified Quadratic- Congruence (MQC) has been carried out.
Abstract: The self-organizing map (SOM) model is a well-known neural network model with wide spread of applications. The main characteristics of SOM are two-fold, namely dimension reduction and topology preservation. Using SOM, a high-dimensional data space will be mapped to some low-dimensional space. Meanwhile, the topological relations among data will be preserved. With such characteristics, the SOM was usually applied on data clustering and visualization tasks. However, the SOM has main disadvantage of the need to know the number and structure of neurons prior to training, which are difficult to be determined. Several schemes have been proposed to tackle such deficiency. Examples are growing/expandable SOM, hierarchical SOM, and growing hierarchical SOM. These schemes could dynamically expand the map, even generate hierarchical maps, during training. Encouraging results were reported. Basically, these schemes adapt the size and structure of the map according to the distribution of training data. That is, they are data-driven or dataoriented SOM schemes. In this work, a topic-oriented SOM scheme which is suitable for document clustering and organization will be developed. The proposed SOM will automatically adapt the number as well as the structure of the map according to identified topics. Unlike other data-oriented SOMs, our approach expands the map and generates the hierarchies both according to the topics and their characteristics of the neurons. The preliminary experiments give promising result and demonstrate the plausibility of the method.