Abstract: The damage tolerance behavior of integrally and
conventional stiffened panel is investigated based on the fracture
mechanics and finite element analysis. The load bearing capability
and crack growth characteristic of both types of the stiffened panels
having same configuration subjected to distributed tensile load is
examined in this paper. A fourteen-stringer stiffened panel is
analyzed for a central skin crack propagating towards the adjacent
stringers. Stress intensity factors and fatigue crack propagation rates
of both types of the stiffened panels are then compared. The analysis
results show that integral stiffening causes higher stress intensity
factor than conventional stiffened panel as the crack tip passes
through the stringer and the integrally stiffened panel has less load
bearing capability than the riveted stiffened panel.
Abstract: In order to evaluation the effects of soil organic
matter and biofertilizer on chickpea quality and biological
nitrogen fixation, field experiments were carried out in 2007
and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on
grain yield and yield component, minerals, organic compounds
and cooking time of chickpea. Experimental units were
arranged in split-split plots based on randomized complete
blocks with three replications. Main plots consisted of (G1):
establishing a mixed vegetation of Vicia panunica and
Hordeum vulgare and (G2): control, as green manure levels.
Also, five strategies for obtaining the base fertilizer
requirement including (N1): 20 t.ha-1 farmyard manure; (N2):
10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5):
10 t.ha-1 farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1
triple super phosphate were considered in sub plots.
Furthermoree four levels of biofertilizers consisted of (B1):
Bacillus lentus + Pseudomonas putida; (B2): Trichoderma
harzianum; (B3): Bacillus lentus + Pseudomonas putida +
Trichoderma harzianum; and (B4): control (without
biofertilizers) were arranged in sub-sub plots. Results showed
that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield
were obtained in G1×N5 interaction. Comparison of all 2-way
and 3-way interactions showed that G1N5B3 was determined
as the superior treatment. Significant increasing of N, P2O5,
K2O, Fe and Mg content in leaves and grains emphasized on
superiority of mentioned treatment because each one of these
nutrients has an approved role in chlorophyll synthesis and
photosynthesis abilities of the crops. The combined application
of compost, farmyard manure and chemical phosphorus (N5)
in addition to having the highest yield, had the best grain
quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.
Abstract: Based on Rayleigh beam theory, the sub-impacts of a
free-free beam struck horizontally by a round-nosed rigid mass is
simulated by the finite difference method and the impact-separation
conditions. In order to obtain the sub-impact force, a uniaxial
compression elastic-plastic contact model is employed to analyze the
local deformation field on contact zone. It is found that the horizontal
impact is a complicated process including the elastic plastic
sub-impacts in sequence. There are two sub-zones of sub-impact. In
addition, it found that the elastic energy of the free-free beam is more
suitable for the Poisson collision hypothesis to explain compression
and recovery processes.
Abstract: The equilibrium, thermodynamics and kinetics of the
biosorption of Cd (II) and Pb(II) by a Spore Forming Bacillus (MGL
75) were investigated at different experimental conditions. The
Langmuir and Freundlich, and Dubinin-Radushkevich (D-R)
equilibrium adsorption models were applied to describe the
biosorption of the metal ions by MGL 75 biomass. The Langmuir
model fitted the equilibrium data better than the other models.
Maximum adsorption capacities q max for lead (II) and cadmium (II)
were found equal to 158.73mg/g and 91.74 mg/g by Langmuir model.
The values of the mean free energy determined with the D-R equation
showed that adsorption process is a physiosorption process. The
thermodynamic parameters Gibbs free energy (ΔG°), enthalpy (ΔH°),
and entropy (ΔS°) changes were also calculated, and the values
indicated that the biosorption process was exothermic and
spontaneous. Experiment data were also used to study biosorption
kinetics using pseudo-first-order and pseudo-second-order kinetic
models. Kinetic parameters, rate constants, equilibrium sorption
capacities and related correlation coefficients were calculated and
discussed. The results showed that the biosorption processes of both
metal ions followed well pseudo-second-order kinetics.
Abstract: This frame work describes a computationally more
efficient and adaptive threshold estimation method for image
denoising in the wavelet domain based on Generalized Gaussian
Distribution (GGD) modeling of subband coefficients. In this
proposed method, the choice of the threshold estimation is carried out
by analysing the statistical parameters of the wavelet subband
coefficients like standard deviation, arithmetic mean and geometrical
mean. The noisy image is first decomposed into many levels to
obtain different frequency bands. Then soft thresholding method is
used to remove the noisy coefficients, by fixing the optimum
thresholding value by the proposed method. Experimental results on
several test images by using this method show that this method yields
significantly superior image quality and better Peak Signal to Noise
Ratio (PSNR). Here, to prove the efficiency of this method in image
denoising, we have compared this with various denoising methods
like wiener filter, Average filter, VisuShrink and BayesShrink.
Abstract: In this paper, we consider the problem of logic simplification for a special class of logic functions, namely complementary Boolean functions (CBF), targeting low power implementation using static CMOS logic style. The functions are uniquely characterized by the presence of terms, where for a canonical binary 2-tuple, D(mj) ∪ D(mk) = { } and therefore, we have | D(mj) ∪ D(mk) | = 0 [19]. Similarly, D(Mj) ∪ D(Mk) = { } and hence | D(Mj) ∪ D(Mk) | = 0. Here, 'mk' and 'Mk' represent a minterm and maxterm respectively. We compare the circuits minimized with our proposed method with those corresponding to factored Reed-Muller (f-RM) form, factored Pseudo Kronecker Reed-Muller (f-PKRM) form, and factored Generalized Reed-Muller (f-GRM) form. We have opted for algebraic factorization of the Reed-Muller (RM) form and its different variants, using the factorization rules of [1], as it is simple and requires much less CPU execution time compared to Boolean factorization operations. This technique has enabled us to greatly reduce the literal count as well as the gate count needed for such RM realizations, which are generally prone to consuming more cells and subsequently more power consumption. However, this leads to a drawback in terms of the design-for-test attribute associated with the various RM forms. Though we still preserve the definition of those forms viz. realizing such functionality with only select types of logic gates (AND gate and XOR gate), the structural integrity of the logic levels is not preserved. This would consequently alter the testability properties of such circuits i.e. it may increase/decrease/maintain the same number of test input vectors needed for their exhaustive testability, subsequently affecting their generalized test vector computation. We do not consider the issue of design-for-testability here, but, instead focus on the power consumption of the final logic implementation, after realization with a conventional CMOS process technology (0.35 micron TSMC process). The quality of the resulting circuits evaluated on the basis of an established cost metric viz., power consumption, demonstrate average savings by 26.79% for the samples considered in this work, besides reduction in number of gates and input literals by 39.66% and 12.98% respectively, in comparison with other factored RM forms.
Abstract: Selection of the best possible set of suppliers has a
significant impact on the overall profitability and success of any
business. For this reason, it is usually necessary to optimize all
business processes and to make use of cost-effective alternatives for
additional savings. This paper proposes a new efficient context-aware
supplier selection model that takes into account possible changes of
the environment while significantly reducing selection costs. The
proposed model is based on data clustering techniques while
inspiring certain principles of online algorithms for an optimally
selection of suppliers. Unlike common selection models which re-run
the selection algorithm from the scratch-line for any decision-making
sub-period on the whole environment, our model considers the
changes only and superimposes it to the previously defined best set
of suppliers to obtain a new best set of suppliers. Therefore, any recomputation
of unchanged elements of the environment is avoided
and selection costs are consequently reduced significantly. A
numerical evaluation confirms applicability of this model and proves
that it is a more optimal solution compared with common static
selection models in this field.
Abstract: This policy participation action research explores the
roles of Thai government units during its 2010 fiscal year on how to
create value added to recycling business in the central part of
Thailand. The research aims to a) study how the government plays a
role to support the business, and its problems and obstacles on
supporting the business, b) to design a strategic action – short,
medium, and long term plans -- to create value added to the recycling
business, particularly in local full-loop companies/organizations
licensed by Wongpanit Waste Separation Plant as well as those
licensed by the Department of Provincial Administration. Mixed
method research design, i.e., a combination of quantitative and
qualitative methods is utilized in the present study in both data
collection and analysis procedures. Quantitative data was analyzed
by frequency, percent value, mean scores, and standard deviation,
and aimed to note trend and generalizations. Qualitative data was
collected via semi-structured interviews/focus group interviews to
explore in-depth views of the operators. The sampling included 1,079
operators in eight provinces in the central part of Thailand.
Abstract: This paper is prepared to provide a review of how an automotive manufacturer, ISUZU HICOM Malaysia Co. Ltd. sustained the supply chain management after business process reengineering in 2007. One of the authors is currently undergoing industrial attachment and has spent almost 6 months researching in the production and operation management system of the company. This study was carried out as part of the tasks in the attachment program. The result shows that delivery lateness and outsourcing are the main barriers that affected productivity. From the gap analysis, the authors found that new business process operation had improved suppliers delivery performance.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: Evaluation and survey of curriculum quality as one of the most important components of universities system is necessary for different levels in higher education. The main purpose of this study was to survey of the curriculum quality of Actuarial science field. Case: University of SHahid Beheshti and Higher education institute of Eco insurance (according to viewpoint of students, alumni, employers and faculty members). Descriptive statistics (mean, tables, percentage, and frequency distribution) and inferential statistics (CHI SQUARE) were used to analyze the data. Six criteria considered for the Quality of curriculum: objectives, content, teaching and learning methods, space and facilities, Time, assessment of learning. Content, teaching and learning methods, space and facilities, assessment of learning criteria were relatively desirable level, objectives and time criterions were desirable level. The quality of curriculum of Actuarial Science field was relatively desirable level.
Abstract: Pretreatment of oil palm empty fruit bunch (OPEFB) with N-Methylmorpholine-N-oxide (NMMO) to enhance biogas production was investigated. The pretreatments were performed at 90 and 120ºC for 1, 3, and 5 h using three different concentrations of NMMO of 73%, 79%, and 85%. The pretreated OPEFB was subsequently anaerobically digested to produce biogas. After pretreatment, there were no significant changes of the main composition of OPEFB and the maximum total solid recovery was 92%. The amorphous phase was increased up to 78% at pretreatment condition using 85% NMMO solution for 3 h at 120oC. In general, higher concentration of NMMO and higher temperature resulted in increased amorphous form and higher biogas production. The best results of biogas production reached enhancement of methane yield of 148% compared to the untreated OPEFB and increased in digestion of 94% compared to starch as reference.
Abstract: This study determines the effect of naked and heparinbased
super-paramagnetic iron oxide nanoparticles on the human
cancer cell lines of A2780. Doxorubicin was used as the anticancer
drug, entrapped in the SPIO-NPs. This study aimed to decorate
nanoparticles with heparin, a molecular ligand for 'active' targeting
of cancerous cells and the application of modified-nanoparticles in
cancer treatment. The nanoparticles containing the anticancer drug
DOX were prepared by a solvent evaporation and emulsification
cross-linking method. The physicochemical properties of the
nanoparticles were characterized by various techniques, and uniform
nanoparticles with an average particle size of 110±15 nm with high
encapsulation efficiencies (EE) were obtained. Additionally, a
sustained release of DOX from the SPIO-NPs was successful.
Cytotoxicity tests showed that the SPIO-DOX-HP had higher cell
toxicity than the individual HP and confocal microscopy analysis
confirmed excellent cellular uptake efficiency. These results indicate
that HP based SPIO-NPs have potential uses as anticancer drug
carriers and also have an enhanced anticancer effect.
Abstract: The Niger Delta Region of Nigeria is home to about
20 million people and 40 different ethnic groups. The region has an
area of seventy thousand square kilometers (70,000 KM2) of
wetlands, formed primarily by sediments deposition and makes up
7.5 percent of Nigeria's total landmass. The notable ecological zones
in this region includes: coastal barrier islands; mangrove swamp
forests; fresh water swamps; and lowland rainforests. This incredibly
naturally-endowed ecosystem region, which contains one of the
highest concentrations of biodiversity on the planet, in addition to
supporting abundant flora and fauna, is threatened by the inhuman act
known as gas flaring. Gas flaring is the combustion of natural gas
that is associated with crude oil when it is pumped up from the
ground. In petroleum-producing areas such as the Niger Delta region
of Nigeria where insufficient investment was made in infrastructure
to utilize natural gas, flaring is employed to dispose of this associated
gas. This practice has impoverished the communities where it is
practiced, with attendant environmental, economic and health
challenges. This paper discusses the adverse environmental and
health implication associated with the practice, the role of
Government, Policy makers, Oil companies and the Local
communities aimed at bring this inhuman practice to a prompt end.
Abstract: Planning the transition period for the adoption of
alternative fuel-technology powertrains is a challenging task that
requires sophisticated analysis tools. In this study, a system dynamic
approach was applied to analyze the bi-directional interaction
between the development of the refueling station network and vehicle
sales. Besides, the developed model was used to estimate the
transition cost to reach a predefined target (share of alternative fuel
vehicles) in different scenarios. Several scenarios have been analyzed
to investigate the effectiveness and cost of incentives on the initial
price of vehicles, and on the evolution of fuel and refueling stations.
Obtained results show that a combined set of incentives will be more
effective than just a single specific type of incentives.
Abstract: For numerical prediction of the NOX in the exhaust of
a compression ignition engine a model was developed by considering
the parameter equivalence ratio. This model was validated by
comparing the predicted results of NOX with experimental ones. The
ultimate aim of the work was to access the applicability, robustness
and performance of the improved NOX model against other NOX
models.
Abstract: DNA shuffling is a powerful method used for in vitro
evolute molecules with specific functions and has application in areas
such as, for example, pharmaceutical, medical and agricultural
research. The success of such experiments is dependent on a variety
of parameters and conditions that, sometimes, can not be properly
pre-established. Here, two computational models predicting DNA
shuffling results is presented and their use and results are evaluated
against an empirical experiment. The in silico and in vitro results
show agreement indicating the importance of these two models and
motivating the study and development of new models.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.
Abstract: Particle Swarm Optimization (PSO) with elite PSO
parameters has been developed for power flow analysis under
practical constrained situations. Multiple solutions of the power flow
problem are useful in voltage stability assessment of power system.
A method of determination of multiple power flow solutions is
presented using a hybrid of Particle Swarm Optimization (PSO) and
local search technique. The unique and innovative learning factors of
the PSO algorithm are formulated depending upon the node power
mismatch values to be highly adaptive with the power flow problems.
The local search is applied on the pbest solution obtained by the PSO
algorithm in each iteration. The proposed algorithm performs reliably
and provides multiple solutions when applied on standard and illconditioned
systems. The test results show that the performances of
the proposed algorithm under critical conditions are better than the
conventional methods.
Abstract: Structural behavior of ring stiffened thick walled
cylinders made of functionally graded materials (FGMs) is
investigated in this paper. Functionally graded materials are inhomogeneous composites which are usually made from a mixture
of metal and ceramic. The gradient compositional variation of the
constituents from one surface to the other provides an elegant solution to the problem of high transverse shear stresses that are
induced when two dissimilar materials with large differences in material properties are bonded. FGM formation of the cylinder is
modeled by power-law exponent and the variation of characteristics is supposed to be in radial direction.
A finite element formulation is derived for the analysis. According to the property variation of the constituent materials in the radial
direction of the wall, it is not convenient to use conventional elements to model and analyze the structure of the stiffened FGM
cylinders. In this paper a new cylindrical super-element is used to model the finite element formulation and analyze the static and
modal behavior of stiffened FGM thick walled cylinders. By using
this super-element the number of elements, which are needed for
modeling, will reduce significantly and the process time is less in comparison with conventional finite element formulations. Results for static and modal analysis are evaluated and verified by
comparison to finite element formulation with conventional
elements. Comparison indicates a good conformity between results.