Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: Many footbridges have natural frequencies that
coincide with the dominant frequencies of the pedestrian-induced
load and therefore they have a potential to suffer excessive vibrations
under dynamic loads induced by pedestrians. Some of the design
standards introduce load models for pedestrian loads applicable for
simple structures. Load modeling for more complex structures, on the
other hand, is most often left to the designer. The main focus of this
paper is on the human induced forces transmitted to a footbridge and
on the ways these loads can be modeled to be used in the dynamic
design of footbridges. Also design criteria and load models proposed
by widely used standards were introduced and a comparison was
made. The dynamic analysis of the suspension bridge in Kolin in the
Czech Republic was performed on detailed FEM model using the
ANSYS program system. An attempt to model the load imposed by a
single person and a crowd of pedestrians resulted in displacements
and accelerations that are compared with serviceability criteria.
Abstract: Deep and radical social reforms of the last century-s
nineties in many Eastern European countries caused changes in
Information Technology-s (IT) field. Inefficient information
technologies were rapidly replaced with forefront IT solutions, e.g.,
in Eastern European countries there is a high level penetration of
qualitative high-speed Internet. The authors have taken part in the
introduction of those changes in Latvia-s leading IT research
institute. Grounding on their experience authors in this paper offer an
IT services based model for analysis the mentioned changes- and
development processes in the higher education and research fields,
i.e., for research e-infrastructure-s development. Compare to the
international practice such services were developed in Eastern Europe
in an untraditional way, which provided swift and positive
technological changes.
Abstract: Evolutionary Algorithms are population-based,
stochastic search techniques, widely used as efficient global
optimizers. However, many real life optimization problems often
require finding optimal solution to complex high dimensional,
multimodal problems involving computationally very expensive
fitness function evaluations. Use of evolutionary algorithms in such
problem domains is thus practically prohibitive. An attractive
alternative is to build meta models or use an approximation of the
actual fitness functions to be evaluated. These meta models are order
of magnitude cheaper to evaluate compared to the actual function
evaluation. Many regression and interpolation tools are available to
build such meta models. This paper briefly discusses the
architectures and use of such meta-modeling tools in an evolutionary
optimization context. We further present two evolutionary algorithm
frameworks which involve use of meta models for fitness function
evaluation. The first framework, namely the Dynamic Approximate
Fitness based Hybrid EA (DAFHEA) model [14] reduces
computation time by controlled use of meta-models (in this case
approximate model generated by Support Vector Machine
regression) to partially replace the actual function evaluation by
approximate function evaluation. However, the underlying
assumption in DAFHEA is that the training samples for the metamodel
are generated from a single uniform model. This does not take
into account uncertain scenarios involving noisy fitness functions.
The second model, DAFHEA-II, an enhanced version of the original
DAFHEA framework, incorporates a multiple-model based learning
approach for the support vector machine approximator to handle
noisy functions [15]. Empirical results obtained by evaluating the
frameworks using several benchmark functions demonstrate their
efficiency
Abstract: This article discusses the customs and traditions in
Turkestan in the late XIXth and early XXth centuries. Having a long
history, Turkestan is well-known as the birthplace of many nations
and nationalities. The name of Turkestan is also given to it for a
reason - the land of the Turkic peoples who inhabited Central Asia
and united under together. Currently, nations and nationalities of the
Turkestan region formed their own sovereign states, and every year
they prove their country names in the world community. Political,
economic importance of Turkestan, which became the gold wire
between Asia and Europe was always very high. So systematically
various aggressive actions were made by several great powers. As a
result of expansionary policy of colonization of the Russian Empire -
the Turkestan has appeared.
Abstract: The wind resource in the Italian site of Lendinara
(RO) is analyzed through a systematic anemometric campaign
performed on the top of the bell tower, at an altitude of over 100 m
above the ground. Both the average wind speed and the Weibull
distribution are computed. The resulting average wind velocity is in
accordance with the numerical predictions of the Italian Wind Atlas,
confirming the accuracy of the extrapolation of wind data adopted for
the evaluation of wind potential at higher altitudes with respect to the
commonly placed measurement stations.
Abstract: The study explored the question of who am I? As a (re)construction of cultural identity by delving into globalization, communication, and social change in Malta during a historical moment when Malta became a European Union Member State. Three objectives guided this qualitative study. Firstly the study reviewed European Union (EU) policies that regulate broadcasting and their implementation in Member States, whilst meeting the challenges of globalization and new media technology. Secondly the research investigated the changes of the media landscape via organizational structures, programs and television (TV) content. Finally the study explored the impact of these transformations taking place in the way Maltese live as they (re)construct their cultural identity. Despite the choices available to the Maltese audience, old local traditions and new foreign customs coexist as informants continue to (re)construct their cultural identity and define who they are.
Abstract: In this study, workplace environmental monitoring
systems were established using USN(Ubiquitous Sensor Networks)
and LabVIEW. Although existing direct sampling methods enable
finding accurate values as of the time points of measurement, those
methods are disadvantageous in that continuous management and
supervision are difficult and costs for are high when those methods are
used. Therefore, the efficiency and reliability of workplace
management by supervisors are relatively low when those methods are
used. In this study, systems were established so that information on
workplace environmental factors such as temperatures, humidity and
noises is measured and transmitted to the PC in real time to enable
supervisors to monitor workplaces through LabVIEW on the PC.
When any accidents have occurred in workplaces, supervisors can
immediately respond through the monitoring system and this system
enables integrated workplace management and the prevention of
safety accidents. By introducing these monitoring systems, safety
accidents due to harmful environmental factors in workplaces can be
prevented and these monitoring systems will be also helpful in finding
out the correlation between safety accidents and occupational diseases
by comparing and linking databases established by this monitoring
system with existing statistical data.
Abstract: Proactive coping directed at an upcoming as opposed
to an ongoing stressor, is a new focus in positive psychology. The
present study explored the proactive coping-s effect on the workplace
adaptation after transition from college to workplace. In order to
demonstrate the influence process between them, we constructed the
model of proactive coping style effecting the actual positive coping
efforts and outcomes by mediating proactive competence during one
year after the transition. Participants (n = 100) started to work right
after graduating from college completed all the four time-s surveys
--one month before (Time 0), one month after (Time 1), three months
after (Time 2), and one year after (Time 3) the transition. Time 0
survey included the measurement of proactive coping style and
competence. Time 1, 2, 3 surveys included the measurement of the
challenge cognitive appraisal, problem solving coping strategy, and
subjective workplace adaptation. The result indicated that proactive
coping style effected newcomers- actual coping efforts and outcomes
by mediating proactive coping competence. The result also showed
that proactive coping competence directly promoted Time1-s actual
positive coping efforts and outcomes, and indirectly promoted Time
2-s and Time 3-s.
Abstract: This paper presents a new approach for image
segmentation by applying Pillar-Kmeans algorithm. This
segmentation process includes a new mechanism for clustering the
elements of high-resolution images in order to improve precision and
reduce computation time. The system applies K-means clustering to
the image segmentation after optimized by Pillar Algorithm. The
Pillar algorithm considers the pillars- placement which should be
located as far as possible from each other to withstand against the
pressure distribution of a roof, as identical to the number of centroids
amongst the data distribution. This algorithm is able to optimize the
K-means clustering for image segmentation in aspects of precision
and computation time. It designates the initial centroids- positions
by calculating the accumulated distance metric between each data
point and all previous centroids, and then selects data points which
have the maximum distance as new initial centroids. This algorithm
distributes all initial centroids according to the maximum
accumulated distance metric. This paper evaluates the proposed
approach for image segmentation by comparing with K-means and
Gaussian Mixture Model algorithm and involving RGB, HSV, HSL
and CIELAB color spaces. The experimental results clarify the
effectiveness of our approach to improve the segmentation quality in
aspects of precision and computational time.
Abstract: Thermoelastic temperature, displacement, and
stress in heat transfer during laser surface hardening are solved
in Eulerian formulation. In Eulerian formulations the heat flux
is fixed in space and the workpiece is moved through a control
volume. In the case of uniform velocity and uniform heat flux
distribution, the Eulerian formulations leads to a steady-state
problem, while the Lagrangian formulations remains transient.
In Eulerian formulations the reduction to a steady-state
problem increases the computational efficiency. In this study
also an analytical solution is developed for an uncoupled
transient heat conduction equation in which a plane slab is
heated by a laser beam. The thermal result of the numerical
model is compared with the result of this analytical model.
Comparing the results shows numerical solution for uncoupled
equations are in good agreement with the analytical solution.
Abstract: Grid environments include aggregation of
geographical distributed resources. Grid is put forward in three types
of computational, data and storage. This paper presents a research on
data grid. Data grid is used for covering and securing accessibility to
data from among many heterogeneous sources. Users are not worry
on the place where data is located in it, provided that, they should get
access to the data. Metadata is used for getting access to data in data
grid. Presently, application metadata catalogue and SRB middle-ware
package are used in data grids for management of metadata. At this
paper, possibility of updating, streamlining and searching is provided
simultaneously and rapidly through classified table of preserving
metadata and conversion of each table to numerous tables.
Meanwhile, with regard to the specific application, the most
appropriate and best division is set and determined. Concurrency of
implementation of some of requests and execution of pipeline is
adaptability as a result of this technique.
Abstract: The daily growing use of agents in software environments, because of many reasons such as independence and intelligence is not a secret anymore. One of such environments in which there is a prominent job for the agents would be emarketplaces in which a user is able to give those agents the responsibility of buying and selling, instead of searching the emarketplace himself. Making up a framework which has sufficient attention to the required roles and their relations, is the first step of achieving such e-markets. In this paper, we suggest a framework in order to establish such e-markets and we will continue investigating the roles such as seller or buyer and the relations in JADE environment in details.
Abstract: Installation of power compensation equipment in
some cases places additional buses into the system. Therefore, a total
number of power flow equations and voltage unknowns increase due
to additional locations of installed devices. In this circumstance, power flow calculation is more complicated. It may result in a
computational convergence problem. This paper presents a power flow calculation by using Newton-Raphson iterative method together
with the proposed load transfer technique. This concept is to eliminate additional buses by transferring installed loads at the new buses to existing two adjacent buses. Thus, the total number of power
flow equations is not changed. The overall computational speed is
expectedly shorter than that of solving the problem without applying the load transfer technique. A 15-bus test system is employed for test
to evaluate the effectiveness of the proposed load transfer technique. As a result, the total number of iteration required and execution time
is significantly reduced.
Abstract: Recently, as information industry and mobile
communication technology are developing, this study is conducted on
the new concept of intelligent structures and maintenance techniques
that applied wireless sensor network, USN (Ubiquitous Sensor
Network), to social infrastructures such as civil and architectural
structures on the basis of the concept of Ubiquitous Computing that
invisibly provides human life with computing, along with mutually
cooperating, compromising and connecting networks each other by
having computers within all objects around us.
Therefore, the purpose of this study is to investigate the capability
of wireless communication of sensor node embedded in reinforced
concrete structure with a basic experiment on an electric wave
permeability of sensor node by fabricating molding with variables of
concrete thickness and steel bars that are mostly used in constructing
structures to determine the feasibility of application to constructing
structures with USN.
At this time, with putting the pitches of steel bars, the thickness of
concrete placed, and the intensity of RF signal of a
transmitter-receiver as variables and when wireless communication
module was installed inside, the possible communication distance of
plain concrete and the possible communication distance by the pitches
of steel bars was measured in the horizontal and vertical direction
respectively. Besides, for the precise measurement of diminution of an
electric wave, the magnitude of an electric wave in the range of used
frequencies was measured by using Spectrum Analyzer. The
phenomenon of diminution of an electric wave was numerically
analyzed and the effect of the length of wavelength of frequencies was
analyzed by the properties of a frequency band area.
As a result of studying the feasibility of an application to
constructing structures with wireless sensor, in case of plain concrete,
it shows 45cm for the depth of permeability and in case of reinforced
concrete with the pitches of 5cm, it shows 37cm and 45cm for the
pitches of 15cm.
Abstract: In order to provide and maintain effective pedagogy for the burgeoning virtual reality community, it is vital to have trained faculty in the institutions of higher education who will teach these courses and be able to make full use of their academic knowledge and expertise. As the number of online courses continues to grow, there is a need for these institutions to establish mentoring programs that will support the novice online instructor. The environment in which this takes place and the factors that ensure its success are critical to the adoption of the new instructional delivery format taught by both seasoned educators and adjunct instructors. Effective one-on-one mentoring promotes a professional, compassionate and collegial faculty who will provide a consistent and rigorous academic program for students online.
Abstract: Contour filter strips planted with perennial vegetation
can be used to improve surface and ground water quality by reducing
pollutant, such as NO3-N, and sediment outflow from cropland to a
river or lake. Meanwhile, the filter strips of perennial grass with biofuel
potentials also have economic benefits of producing ethanol. In
this study, The Soil and Water Assessment Tool (SWAT) model was
applied to the Walnut Creek Watershed to examine the effectiveness
of contour strips in reducing NO3-N outflows from crop fields to the
river or lake. Required input data include watershed topography,
slope, soil type, land-use, management practices in the watershed and
climate parameters (precipitation, maximum/minimum air
temperature, solar radiation, wind speed and relative humidity).
Numerical experiments were conducted to identify potential
subbasins in the watershed that have high water quality impact, and
to examine the effects of strip size and location on NO3-N reduction
in the subbasins under various meteorological conditions (dry,
average and wet). Variable sizes of contour strips (10%, 20%, 30%
and 50%, respectively, of a subbasin area) planted with perennial
switchgrass were selected for simulating the effects of strip size and
location on stream water quality. Simulation results showed that a
filter strip having 10%-50% of the subbasin area could lead to 55%-
90% NO3-N reduction in the subbasin during an average rainfall
year. Strips occupying 10-20% of the subbasin area were found to be
more efficient in reducing NO3-N when placed along the contour
than that when placed along the river. The results of this study can
assist in cost-benefit analysis and decision-making in best water
resources management practices for environmental protection.
Abstract: Sensorized instruments that accurately measure the interaction forces (between biological tissue and instrument endeffector) during surgical procedures offer surgeons a greater sense of immersion during minimally invasive robotic surgery. Although there is ongoing research into force measurement involving surgical graspers little corresponding effort has been carried out on the measurement of forces between scissor blades and tissue. This paper presents the design and development of a force measurement test apparatus, which will serve as a sensor characterization and evaluation platform. The primary aim of the experiments is to ascertain whether the system can differentiate between tissue samples with differing mechanical properties in a reliable, repeatable manner. Force-angular displacement curves highlight trends in the cutting process as well the forces generated along the blade during a cutting procedure. Future applications of the test equipment will involve the assessment of new direct force sensing technologies for telerobotic surgery.
Abstract: Rapid Prototyping (RP) is a technology that produces models and prototype parts from 3D CAD model data, CT/MRI scan data, and model data created from 3D object digitizing systems. There are several RP process like Stereolithography (SLA), Solid Ground Curing (SGC), Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM), 3D Printing (3DP) among them SLS and FDM RP processes are used to fabricate pattern of custom cranial implant. RP technology is useful in engineering and biomedical application. This is helpful in engineering for product design, tooling and manufacture etc. RP biomedical applications are design and development of medical devices, instruments, prosthetics and implantation; it is also helpful in planning complex surgical operation. The traditional approach limits the full appreciation of various bony structure movements and therefore the custom implants produced are difficult to measure the anatomy of parts and analyze the changes in facial appearances accurately. Cranioplasty surgery is a surgical correction of a defect in cranial bone by implanting a metal or plastic replacement to restore the missing part. This paper aims to do a comparative study on the dimensional error of CAD and SLS RP Models for reconstruction of cranial defect by comparing the virtual CAD with the physical RP model of a cranial defect.
Abstract: As new challenges emerge in power electrical
workplace safety, it is the responsibility of the systems designer to
seek out new approaches and solutions that address them. Design
decisions made today will impact cost, safety and serviceability of
the installed systems for 40 or 50 years during the useful life for the
owner. Studies have shown that this cost is an order of magnitude of
7 to 10 times the installed cost of the power distribution equipment.
This paper reviews some aspects of earthing system design in power
substation surrounded by residential houses. The electrical potential
rise and split factors are discussed and a few recommendations are
provided to achieve a safety voltage in the area beyond the boundary
of the substation.