Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: A passive system "Qanat" is collection of some
underground wells. A mother-well was dug in a place far from the
city where they could reach to the water table maybe 100 meters
underground, they dug other wells to direct water toward the city,
with minimum possible gradient. Using the slope of the earth they
could bring water close to the surface in the city. The source of water
or the appearance of Qanat, land slope and the ownership lines are
the important and effective factors in the formation of routes and the
segment division of lands to the extent that making use of Qanat as
the techniques of extracting underground waters creates a channel of
routes with an organic order and hierarchy coinciding the slope of
land and it also guides the Qanat waters in the tradition texture of salt
desert and border provinces of it. Qanats are excavated in a specified
distinction from each other. The quantity of water provided by
Qanats depends on the kind of land, distance from mountain,
geographical situation of them and the rate of water supply from the
underground land. The rate of underground waters, possibility of
Qanat excavation, number of Qanats and rate of their water supply
from one hand and the quantity of cultivable fertile lands from the
other hand are the important natural factors making the size of cities.
In the same manner the cities with several Qanats have multi central
textures. The location of cities is in direct relation with land quality,
soil fertility and possibility of using underground water by excavating
Qanats. Observing the allowable distance for Qanat watering is a
determining factor for distance between villages and cities.
Topography, land slope, soil quality, watering system, ownership,
kind of cultivation, etc. are the effective factors in directing Qanats
for excavation and guiding water toward the cultivable lands and it
also causes the formation of different textures in land division of
farming provinces. Several divisions such as orderly and wide, inorderly,
thin and long, comb like, etc. are the introduction to organic
order. And at the same time they are complete coincidence with
environmental conditions in the typical development of ecological
architecture and planning in the traditional cities and settlements
order.
Abstract: This study aims to segment objects using the K-means
algorithm for texture features. Firstly, the algorithm transforms color
images into gray images. This paper describes a novel technique for
the extraction of texture features in an image. Then, in a group of
similar features, objects and backgrounds are differentiated by using
the K-means algorithm. Finally, this paper proposes a new object
segmentation algorithm using the morphological technique. The
experiments described include the segmentation of single and multiple
objects featured in this paper. The region of an object can be
accurately segmented out. The results can help to perform image
retrieval and analyze features of an object, as are shown in this paper.
Abstract: In this work social stratification is considered as one
of significant factor which generate the phenomena “terrorism” and it
puts the accent on correlation connection between them, with the
object of creation info-logical model generation of phenomena of
“terrorism” based on stratification process.
Abstract: The purpose of this study is to discuss the effect of the
intervention of exercise behavior change plan for high school students
on study subjects- social and psychological factors and exercise
stages. This research uses the transtheoretical model as the research
framework. One experiment group and one control group were used in
a quasi-experimental design research. The experimental group
accepted health-related physical fitness course and the traditional
course; the control group accepted traditional physical education
course. There is a significant difference before and after the
intervention in the experimental group. Karl-s test shows the
experimental group gained a better improvement than that in the
control group. The Analysis of Covariance had shown the exercise
stages (F=7.62, p
Abstract: All over the world, including the Middle and East
European countries, sustainable tillage and sowing technologies are
applied increasingly broadly with a view to optimising soil resources,
mitigating soil degradation processes, saving energy resources,
preserving biological diversity, etc. As a result, altered conditions of
tillage and sowing technological processes are faced inevitably. The
purpose of this study is to determine the seedbed topsoil hardness
when using a combined sowing coulter in different sustainable tillage
technologies. The research involved a combined coulter consisting
of two dissected blade discs and a shoe coulter. In order to determine
soil hardness at the seedbed area, a multipenetrometer was used. It
was found by experimental studies that in loosened soil, a combined
sowing coulter equally suppresses the furrow bottom, walls and soil
near the furrow; therefore, here, soil hardness was similar at all
researched depths and no significant differences were established. In
loosened and compacted (double-rolled) soil, the impact of a
combined coulter on the hardness of seedbed soil surface was more
considerable at a depth of 2 mm. Soil hardness at the furrow bottom
and walls to a distance of up to 26 mm was 1.1 MPa. At a depth of 10
mm, the greatest hardness was established at the furrow bottom. In
loosened and heavily compacted (rolled for 6 times) soil, at a depth
of 2 and 10 mm a combined coulter most of all compacted the furrow
bottom, which has a hardness of 1.8 MPa. At a depth of 20 mm, soil
hardness within the whole investigated area varied insignificantly and
fluctuated by around 2.0 MPa. The hardness of furrow walls and soil
near the furrow was by approximately 1.0 MPa lower than that at the
furrow bottom
Abstract: The human head representations usually are based on
the morphological – structural components of a real model. Over the
time became more and more necessary to achieve full virtual models
that comply very rigorous with the specifications of the human
anatomy. Still, making and using a model perfectly fitted with the
real anatomy is a difficult task, because it requires large hardware
resources and significant times for processing. That is why it is
necessary to choose the best compromise solution, which keeps the
right balance between the details perfection and the resources
consumption, in order to obtain facial animations with real-time
rendering. We will present here the way in which we achieved such a
3D system that we intend to use as a base point in order to create
facial animations with real-time rendering, used in medicine to find
and to identify different types of pathologies.
Abstract: Names are important in many societies, even in technologically oriented ones which use e.g. ID systems to identify individual people. Names such as surnames are the most important as they are used in many processes, such as identifying of people and genealogical research. On the other hand variation of names can be a major problem for the identification and search for people, e.g. web search or security reasons. Name matching presumes a-priori that the recorded name written in one alphabet reflects the phonetic identity of two samples or some transcription error in copying a previously recorded name. We add to this the lode that the two names imply the same person. This paper describes name variations and some basic description of various name matching algorithms developed to overcome name variation and to find reasonable variants of names which can be used to further increasing mismatches for record linkage and name search. The implementation contains algorithms for computing a range of fuzzy matching based on different types of algorithms, e.g. composite and hybrid methods and allowing us to test and measure algorithms for accuracy. NYSIIS, LIG2 and Phonex have been shown to perform well and provided sufficient flexibility to be included in the linkage/matching process for optimising name searching.
Abstract: Ireland developed a National Strategy 2030 that
argued for the creation of a new form of higher education institution,
a Technological University. The research reported here reviews the
first stage of this partnership development. The study found that
national policy can create system capacity and change, but that
individual partners may have more to gain or lose in collaborating.
When presented as a zero-sum activity, fear among partners is high.
The level of knowledge and networking within the higher education
system possessed by each partner contributed to decisions to
participate or not in a joint proposal for collaboration. Greater
success resulted when there were gains for all partners. This research
concludes that policy mandates can provide motivation to
collaborate, but that the partnership needs to be built more on shared
values versus coercion by mandates.
Abstract: In order to increase in chickpea quality and
agroecosystem sustainability, field experiments were carried out in
2007 and 2008 growing seasons. In this research the effects of
different organic, chemical and biological fertilizers were
investigated on grain yield and quality of chickpea. Experimental
units were arranged in split-split plots based on randomized complete
blocks with three replications. The highest amounts of yield and yield
components were obtained in G1×N5 interaction. Significant
increasing of N, P, K, Fe and Mg content in leaves and grains
emphasized on superiority of mentioned treatment because each one
of these nutrients has an approved role in chlorophyll synthesis and
photosynthesis ability of the crop. The combined application of
compost, farmyard manure and chemical phosphorus (N5) had the
best grain quality due to high protein, starch and total sugar contents,
low crude fiber and reduced cooking time.
Abstract: We introduce an algorithm based on the
morphological shared-weight neural network. Being nonlinear and
translation-invariant, the MSNN can be used to create better
generalization during face recognition. Feature extraction is
performed on grayscale images using hit-miss transforms that are
independent of gray-level shifts. The output is then learned by
interacting with the classification process. The feature extraction and
classification networks are trained together, allowing the MSNN to
simultaneously learn feature extraction and classification for a face.
For evaluation, we test for robustness under variations in gray levels
and noise while varying the network-s configuration to optimize
recognition efficiency and processing time. Results show that the
MSNN performs better for grayscale image pattern classification
than ordinary neural networks.
Abstract: Product Lead Time (PLT) is the period of time from
receiving a customer's order to delivering the final product. PLT is an
indicator of the manufacturing controllability, efficiency and
performance. Due to the explosion in the rate of technological
innovations and the rapid changes in the nature of manufacturing
processes, manufacturing firms can bring the new products to market
quicker only if they can reduce their PLT and speed up the rate at
which they can design, plan, control, and manufacture. Although
there is a substantial body of research on manufacturing relating to
cost and quality issues, there is no much specific research conducted
in relation to the formulation of PLT, despite its significance and
importance. This paper analyzes and formulates PLT which can be
used as a guideline for achieving the shorter PLT. Further more this
paper identifies the causes of delay and factors that contributes to the
increased product lead-time.
Abstract: Detecting protein-protein interactions is a central problem in computational biology and aberrant such interactions may have implicated in a number of neurological disorders. As a result, the prediction of protein-protein interactions has recently received considerable attention from biologist around the globe. Computational tools that are capable of effectively identifying protein-protein interactions are much needed. In this paper, we propose a method to detect protein-protein interaction based on substring similarity measure. Two protein sequences may interact by the mean of the similarities of the substrings they contain. When applied on the currently available protein-protein interaction data for the yeast Saccharomyces cerevisiae, the proposed method delivered reasonable improvement over the existing ones.
Abstract: The possibility of radionuclides-related contamination
of lands at agricultural holdings defines the necessity to apply special
protective measures in plant growing. The aim of researches is to
elucidate the influence of polymers applying on biological migration
of man-made anthropogenic radionuclides 90Sr and 137Cs in the
system water - soil – plant. The tests are being carried out under field
conditions with and without application of polymers in root-inhabited
media in more radioecological tension zone (with the radius of 7 km
from the Armenian Nuclear Power Plant). The polymers on the base
of K+, Caµ, KµCaµ ions were tested. Productivity of pepper
depending on the presence and type of polymer material, content of
artificial radionuclides in waters, soil and plant material has been
determined. The character of different polymers influence on the
artificial radionuclides migration and accumulation in the system
water-soil-plant and accumulation in the plants has been cleared up.
Abstract: The volume of XML data exchange is explosively increasing, and the need for efficient mechanisms of XML data management is vital. Many XML storage models have been proposed for storing XML DTD-independent documents in relational database systems. Benchmarking is the best way to highlight pros and cons of different approaches. In this study, we use a common benchmarking scheme, known as XMark to compare the most cited and newly proposed DTD-independent methods in terms of logical reads, physical I/O, CPU time and duration. We show the effect of Label Path, extracting values and storing in another table and type of join needed for each method's query answering.
Abstract: Horseradish (Armoracia rusticana) is a perennial herb belonging to the Brassicaceae family and contains biologically active substances. The aim of the current research was to determine best method for extraction of phenolic compounds from horseradish roots showing high antiradical activity. Three genotypes (No. 105; No. 106 and variety ‘Turku’) of horseradish roots were extracted with eight different solvents: n-hexane, ethyl acetate, diethyl ether, 2-propanol, acetone, ethanol (95%), ethanol / water / acetic acid (80/20/1 v/v/v) and ethanol / water (80/20 by volume) using two extraction methods (conventional and Soxhlet). As the best solvents ethanol and ethanol / water solutions can be chosen. Although in Soxhlet extracts TPC was higher, scavenging activity of DPPH˙ radicals did not increase. It can be concluded that using Soxhlet extraction method more compounds that are not effective antioxidants.
Abstract: Japan is known to be a technological powerhouse, being noted for its automobiles, consumer electronics, laptop computers, portable gaming devices, and more recently healing animal robots. Japan is also noted for its popular culture; manga, anime, novels, films, character goods, game programs, cosplay cafes, karaoke and so on. It may be natural for people outside Japan to assume that e-learning in Japan must be well advanced and innovative. In reality, the application of technologies in education in Japan is far behind of other developed countries. Especially in higher education, apathy of students towards their study prevails and teachers continue ignoring such student attitudes. E-learning, which is supposed to revolutionalize the way people learn as it has potentials to enable more student-centered learning, has not been realized in Japan and mostly used to perpetuate the teachercentered teaching in a different format.
Abstract: Five crystal modifications of water insoluble
artesunate were generated by recrystallizing it from various solvents
with improved physicochemical properties. These generated crystal
forms were characterized to select the most potent and soluble form.
SEM of all the forms showed changes in external shape leading them
to be different morphologically. DSC thermograms of Form III and
Form V showed broad endotherm peaks at 83.04oC and 76.96oC prior
to melting fusion of drug respectively. Calculated weight loss in TGA
revealed that Form III and Form V are methanol and acetone solvates
respectively. However, few additional peaks were appeared in XRPD
pattern in these two solvate forms. All forms exhibit exothermic
behavior in buffer and two solvates display maximum ease of
molecular release from the lattice. Methanol and acetone solvates
were found to be most soluble forms and exhibited higher
antimalarial efficacy showing higher survival rate (83.3%) after 30
days.
Abstract: Current research on semantic web aims at making intelligent web pages meaningful for machines. In this way, ontology plays a primary role. We believe that logic can help ontology languages (such as OWL) to be more fluent and efficient. In this paper we try to combine logic with OWL to reduce some disadvantages of this language. Therefore we extend OWL by logic and also show how logic can satisfy our future expectations of an ontology language.
Abstract: Tensile armour wires provide a flexible pipe's
resistance to longitudinal stresses. Flexible pipe manufacturers need
to know the effect of defects such as scratches and cracks, with
dimensions less than 0.2mm which is the limit of the current nondestructive
detection technology, on the fracture stress and fracture
strain of the wire for quality assurance purposes. Recent research
involving the determination of the fracture strength of cracked wires
employed laboratory testing and classical fracture mechanics
approach using non-standardised fracture mechanics specimens
because standard test specimens could not be manufactured from the
wires owing to their sizes. In this work, the effect of miniature
cracks on the fracture properties of tensile armour wires was
investigated using laboratory and finite element tensile testing
simulations with the phenomenological shear fracture model. The
investigation revealed that the presence of cracks shallower than
0.2mm is worse on the fracture strain of the wire.