Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: This paper presents a system for tracking the movement of laparoscopic instruments which is based on an orthogonal system of webcams and video image processing. The movements are captured with two webcams placed orthogonally inside of the physical trainer. On the image, the instruments were detected by using color markers placed on the distal tip of each instrument. The 3D position of the tip of the instrument within the work space was obtained by linear triangulation method. Preliminary results showed linearity and repeatability in the motion tracking with a resolution of 0.616 mm in each axis; the accuracy of the system showed a 3D instrument positioning error of 1.009 ± 0.101 mm. This tool is a portable and low-cost alternative to traditional tracking devices and a trustable method for the objective evaluation of the surgeon’s surgical skills.
Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: In this paper we illuminate a frequency domain based
classification method for video scenes. Videos from certain topical
areas often contain activities with repeating movements. Sports
videos, home improvement videos, or videos showing mechanical
motion are some example areas. Assessing main and side frequencies
of each repeating movement gives rise to the motion type. We
obtain the frequency domain by transforming spatio-temporal motion
trajectories. Further on we explain how to compute frequency features
for video clips and how to use them for classifying. The focus of
the experimental phase is on transforms utilized for our system.
By comparing various transforms, experiments show the optimal
transform for a motion frequency based approach.
Abstract: The paper proposes the novel design of a 3T XOR gate combining complementary CMOS with pass transistor logic. The design has been compared with earlier proposed 4T and 6T XOR gates and a significant improvement in silicon area and power-delay product has been obtained. An eight transistor full adder has been designed using the proposed three-transistor XOR gate and its performance has been investigated using 0.15um and 0.35um technologies. Compared to the earlier designed 10 transistor full adder, the proposed adder shows a significant improvement in silicon area and power delay product. The whole simulation has been carried out using HSPICE.
Abstract: Purpose of this work is to develop an automatic classification system that could be useful for radiologists in the breast cancer investigation. The software has been designed in the framework of the MAGIC-5 collaboration. In an automatic classification system the suspicious regions with high probability to include a lesion are extracted from the image as regions of interest (ROIs). Each ROI is characterized by some features based generally on morphological lesion differences. A study in the space features representation is made and some classifiers are tested to distinguish the pathological regions from the healthy ones. The results provided in terms of sensitivity and specificity will be presented through the ROC (Receiver Operating Characteristic) curves. In particular the best performances are obtained with the Neural Networks in comparison with the K-Nearest Neighbours and the Support Vector Machine: The Radial Basis Function supply the best results with 0.89 ± 0.01 of area under ROC curve but similar results are obtained with the Probabilistic Neural Network and a Multi Layer Perceptron.
Abstract: The last years have seen an increasing use of image analysis techniques in the field of biomedical imaging, in particular in microscopic imaging. The basic step for most of the image analysis techniques relies on a background image free of objects of interest, whether they are cells or histological samples, to perform further analysis, such as segmentation or mosaicing. Commonly, this image consists of an empty field acquired in advance. However, many times achieving an empty field could not be feasible. Or else, this could be different from the background region of the sample really being studied, because of the interaction with the organic matter. At last, it could be expensive, for instance in case of live cell analyses. We propose a non parametric and general purpose approach where the background is built automatically stemming from a sequence of images containing even objects of interest. The amount of area, in each image, free of objects just affects the overall speed to obtain the background. Experiments with different kinds of microscopic images prove the effectiveness of our approach.
Abstract: This paper presented a proposed design for
transcutaneous inductive powering links. The design used to transfer
power and data to the implanted devices such as implanted
Microsystems to stimulate and monitoring the nerves and muscles.
The system operated with low band frequency 13.56 MHZ according
to industrial- scientific – medical (ISM) band to avoid the tissue
heating. For external part, the modulation index is 13 % and the
modulation rate 7.3% with data rate 1 Mbit/s assuming Tbit=1us. The
system has been designed using 0.35-μm fabricated CMOS
technology. The mathematical model is given and the design is
simulated using OrCAD P Spice 16.2 software tool and for real-time
simulation the electronic workbench MULISIM 11 has been used.
The novel circular plane (pancake) coils was simulated using
ANSOFT- HFss software.
Abstract: Electro-optical devices are increasingly used for
military sea-, land- and air applications to detect, recognize and track
objects. Typically, these devices produce video information that is
presented to an operator. However, with increasing availability of
electro-optical devices the data volume is becoming very large,
creating a rising need for automated analysis. In a military setting,
this typically involves detecting and recognizing objects at a large
distance, i.e. when they are difficult to distinguish from background
and noise. One may consider combining multiple images from a
video stream into a single enhanced image that provides more
information for the operator. In this paper we investigate a simple
algorithm to enhance simulated images from a military context and
investigate how the enhancement is affected by various types of
disturbance.
Abstract: Health problems linked to urban growth are current
major concerns of developing countries. In 2002 and 2005, an
interdisciplinary program “Populations et Espaces ├á Risques
SANitaires" (PERSAN) was set up under the patronage of the
Development and Research Institute. Centered on health in
Cameroon-s urban environment, the program mainly sought to (i)
identify diarrhoea risk factors in Yaoundé, (ii) to measure their
prevalence and apprehend their spatial distribution. The crosssectional
epidemiological study that was carried out revealed a
diarrheic prevalence of 14.4% (437 cases of diarrhoea on the 3,034
children examined). Also, among risk factors studied, household
refuse management methods used by city dwellers were statistically
associated to these diarrhoeas. Moreover, it happened that levels of
diarrhoeal attacks varied consistently from one neighbourhood to
another because of the discrepancy urbanization process of the
Yaoundé metropolis.
Abstract: The curves, of which the square of the distance
between the two points equal to zero, are called minimal or isotropic
curves [4]. In this work, first, necessary and sufficient conditions to
be a Pseudo Helix, which is a special case of such curves, are
presented. Thereafter, it is proven that an isotropic curve-s position
vector and pseudo curvature satisfy a vector differential equation of
fourth order. Additionally, In view of solution of mentioned
equation, position vector of pseudo helices is obtained.
Abstract: Video sensor networks operate on stringent requirements
of latency. Packets have a deadline within which they have
to be delivered. Violation of the deadline causes a packet to be
treated as lost and the loss of packets ultimately affects the quality
of the application. Network latency is typically a function of many
interacting components. In this paper, we propose ways of reducing
the forwarding latency of a packet at intermediate nodes. The
forwarding latency is caused by a combination of processing delay
and queueing delay. The former is incurred in order to determine the
next hop in dynamic routing. We show that unless link failures in a
very specific and unlikely pattern, a vast majority of these lookups
are redundant. To counter this we propose source routing as the
routing strategy. However, source routing suffers from issues related
to scalability and being impervious to network dynamics. We propose
solutions to counter these and show that source routing is definitely
a viable option in practical sized video networks. We also propose a
fast and fair packet scheduling algorithm that reduces queueing delay
at the nodes. We support our claims through extensive simulation on
realistic topologies with practical traffic loads and failure patterns.
Abstract: Firms have invested heavily in knowledge
management (KM) with the aim to build a knowledge capability and
use it to achieve a competitive advantage. Research has shown,
however, that not all knowledge management projects succeed. Some
studies report that about 84% of knowledge management projects
fail. This paper has integrated studies on the impediments to
knowledge management into a theoretical framework. Based on this
framework, five cases documenting failed KM initiatives were
analysed. The analysis gave us a clear picture about why certain KM
projects fail. The high failure rate of KM can be explained by the
gaps that exist between users and management in terms of KM
perceptions and objectives
Abstract: This paper presents the characterization and design of a capacitive pressure sensor with LC-based 0.35 µm CMOS readout circuit. SPICE is employed to evaluate the characteristics of the readout circuit and COMSOL multiphysics structural analysis is used to simulate the behavior of the pressure sensor. The readout circuit converts the capacitance variation of the pressure sensor into the frequency output. Simulation results show that the proposed pressure sensor has output frequency from 2.50 to 2.28 GHz in a pressure range from 0.1 to 2 MPa almost linearly. The sensitivity of the frequency shift with respect to the applied pressure load is 0.11 GHz/MPa.
Abstract: Meshless Finite Element Methods, namely element-free Galerkin and point-interpolation method were implemented and tested concerning their applicability to typical engineering problems like electrical fields and structural mechanics. A class-structure was developed which allows a consistent implementation of these methods together with classical FEM in a common framework. Strengths and weaknesses of the methods under investigation are discussed. As a result of this work joint usage of meshless methods together with classical Finite Elements are recommended.
Abstract: Operational risk has become one of the most discussed topics in the financial industry in the recent years. The reasons for this attention can be attributed to higher investments in information systems and technology, the increasing wave of mergers and acquisitions and emergence of new financial instruments. In addition, the New Basel Capital Accord (known as Basel II) demands a capital requirement for operational risk and further motivates financial institutions to more precisely measure and manage this type of risk. The aim of this paper is to shed light on main characteristics of operational risk management and common applied methods: scenario analysis, key risk indicators, risk control self assessment and loss distribution approach.
Abstract: The essential oil of M. × piperita L. was formulated
into a topical gel. The prepared gel was characterized for its pH,
viscosity, spreadiblity, consistency and extrudiblity, while its stability
was evaluated under different temperature conditions. The prepared
M. × piperita oil gel was clear and transparent. The pH value of
developed gel was 6.6, while its viscosity was 1200 cP. Spreadability
and consistency of the M. × piperita oil gel was 10.7 g.cm/sec and 7
mm, respectively. The prepared gel showed good extrudiblity. During
the stability studies, no significant change in pH and viscosity as a
function of time for gel was observed, indicating stability of prepared
formulation. The gel developed in this study is expected to forward
the usage of M. × piperita essential towards commercial application.
Abstract: Observations and long-term trends indicate that climate
change impacts would be significant and affects Taiwan directly and
severely. Taiwan engages not only in mitigation, but also in adaptation.
However, there are cognitive gaps on adaptation between government
and populace. Besides, a vision of zero-carbon and renewable energy
100% will be adopted in future. Therefore, the objectives of this
article are to 1) hold a National Forum for knowing differences
between the strategies of zero-carbon and renewable energy 100% and
cognitions of general populace, and 2) plan a clear roadmap for the
vision, strategy, and measures. In this forum, we set 5 group topics, 5
presumed themes, and issues mentioned review for concluding the
critical issues. Finally, there are 4 strategies and 14 critical issues
which correlate with the vision and strategy of government and the
cognition of the general populace.
Abstract: This paper focuses on the calibration problem of a
multi-view shooting system designed for the production of 3D
content for auto-stereoscopic visualization. The considered multiview
camera is characterized by coplanar and decentered image
sensors regarding to the corresponding optical axis. Based on the
Faugéras and Toscani-s calibration approach, a calibration method is
herein proposed for the case of multi-view camera with parallel and
decentered image sensors. At first, the geometrical model of the
shooting system is recalled and some industrial prototypes with some
shooting simulations are presented. Next, the development of the
proposed calibration method is detailed. Finally, some simulation
results are presented before ending with some conclusions about this
work.
Abstract: A self-association model has been used to understand
the concentration dependence of free energy of mixing (GM), heat of
mixing (HM), entropy of mixing (SM), activity (a) and microscopic
structures, such as concentration fluctuation in long wavelength limit
(Scc(0)) and Warren-Cowley short range order parameter ( 1
α )for Cu-
Tl molten alloys at 1573K. A comparative study of surface tension of
the alloys in the liquid state at that temperature has also been carried
out theoretically as function of composition in the light of Butler-s
model, Prasad-s model and quasi-chemical approach. Most of the
computed thermodynamic properties have been found in agreement
with the experimental values. The analysis reveals that the Cu-Tl
molten alloys at 1573K represent a segregating system at all
concentrations with moderate interaction. Surface tensions computed
from different approaches have been found to be comparable to each
other showing increment with the composition of copper.