Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: This article is presented an experimental and modeling
study of a four-bed pressure swing adsorption process using
zeolite13X to provide oxygen-enriched air. The binary mixture N2/O2
(79/21 vol %) was used as a feed stream. The effects of purge/feed
ratio (P/F), adsorption pressure, cyclic time and product flow rate on
product purity and recovery under nonisothermal condition were
studied. The adsorption dynamics of process were determined using
a mathematical model incorporated mass and energy balances. A
Mathlab code using finite difference method was developed to solve
the set of coupled differential-algebraic equations, and the simulation
results are agreed well with experimental results.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: In this paper two different Antilock braking system (ABS) are simulated and compared. One is the ordinary hydraulic ABS system which we call it ABS and the other is Electromagnetic Antilock braking system which is called (EMABS) the basis of performance of an EMABS is based upon Electromagnetic force. In this system there is no need to use servo hydraulic booster which are used in ABS system. In EMABS to generate the desired force we have use a magnetic relay which works with an input voltage through an air gap (g). The generated force will be amplified by the relay arm, and is applied to the brake shoes and thus the braking torque is generated. The braking torque is proportional to the applied electrical voltage E. to adjust the braking torque it is only necessary to regulate the electrical voltage E which is very faster and has a much smaller time constant T than the ABS system. The simulations of these two different ABS systems are done with MATLAB/SIMULINK software and the superiority of the EMABS has been shown.
Abstract: The radius-of-curvature (ROC) defines the degree of
curvature along the centerline of a roadway whereby a travelling
vehicle must follow. Roadway designs must encompass ROC in
mitigating the cost of earthwork associated with construction while
also allowing vehicles to travel at maximum allowable design speeds.
Thus, a road will tend to follow natural topography where possible,
but curvature must also be optimized to permit fast, but safe vehicle
speeds. The more severe the curvature of the road, the slower the
permissible vehicle speed. For route planning, whether for urban
settings, emergency operations, or even parcel delivery, ROC is a
necessary attribute of road arcs for computing travel time.
It is extremely rare for a geo-spatial database to contain ROC. This
paper will present a procedure and mathematical algorithm to
calculate and assign ROC to a segment pair and/or polyline.
Abstract: Realistic systems generally are systems with various
inputs and outputs also known as Multiple Input Multiple Output
(MIMO). Such systems usually prove to be complex and difficult to
model and control purposes. Therefore, decomposition was used to
separate individual inputs and outputs. A PID is assigned to each
individual pair to regulate desired settling time. Suitable parameters
of PIDs obtained from Genetic Algorithm (GA), using Mean of
Squared Error (MSE) objective function.
Abstract: Microbial air contamination of the outdoor air in Marine Durres-s Harbour (Durres, Albania) was estimated by sedimentation technique in August-October 2008. The sampling areas were: Ferry Terminal (FT), Fishery Harbor (FH), East Zone (EZ), Fuel Quay (FQ) and Apollonian Beach (AB). The aim of this study was to measure the number of aerobic plate count (mesophilic aerobic bacteria) and fungi (yeasts and molds) in the outdoor air in these areas. The number of colonies that were formed determines the number of cells at the moment in the outdoor air; respectively the number of mesophilic aerobic bacteria and yeasts and molds. The measure of bacteria and fungi used is CFU (Colony Forming Units) per Petri dish. It is said that marine harbours are very polluted areas. The aim of study was the definition of mesophilic aerobic bacteria and yeasts and molds number, and the comparison of microorganisms number in air sampling areas.
Abstract: Building condition assessment is a critical activity in Malaysia-s Comprehensive Asset Management Model. It is closely related to building performance that impact user-s life and decision making. This study focuses on public primary school, one of the most valuable assets for the country. The assessment was carried out based on CSP1 Matrix in Kuching Division of Sarawak, Malaysia. Based on the matrix used, three main criteria of the buildings has successfully evaluate: the number of defects; schools rating; and total schools rating. The analysis carried out on 24 schools found that the overall 4, 725 defects has been identified. Meanwhile, the overall score obtained was 45, 868 and the overall rating is 9.71, which is at the fair condition. This result has been associated with building age to evaluate its impacts on school buildings condition. The findings proved that building condition is closely related to building age and its support the theory that 'the ageing building has more defect than the new one'.
Abstract: The aim of this paper is to present a new
three-dimensional proportional-pursuit coupled (PP) guidance law to
track highly maneuverable aircraft. Utilizing a 3-D polar coordinate frame, the PP guidance law is formed by collecting proportional
navigation guidance in Z-R plane and pursuit guidance in X-Y plane.
Feedback linearization control method to solve the guidance
accelerations is used to implement PP guidance. In order to
compensate the actuator time delay, the time delay compensated
version of PP guidance law (CPP) was derived and proved the
effectiveness of modifying the problem of high acceleration in the final
phase of pursuit guidance and improving the weak robustness of
proportional navigation. The simulation results for intercepting Max G
turn situation show that the proposed proportional-pursuit coupled
guidance law guidance law with actuator delay compensation (CPP)
possesses satisfactory robustness and performance.
Abstract: In the present study, computational fluid dynamics
(CFD) simulation has been executed to investigate the transition
boundaries of different flow patterns for moderately viscous oil-water
(viscosity ratio 107, density ratio 0.89 and interfacial tension of 0.032
N/m.) two-phase flow through a horizontal pipeline with internal
diameter and length of 0.025 m and 7.16 m respectively. Volume of
Fluid (VOF) approach including effect of surface tension has been
employed to predict the flow pattern. Geometry and meshing of the
present problem has been drawn using GAMBIT and ANSYS
FLUENT has been used for simulation. A total of 47037 quadrilateral
elements are chosen for the geometry of horizontal pipeline. The
computation has been performed by assuming unsteady flow,
immiscible liquid pair, constant liquid properties, co-axial flow and a
T-junction as entry section. The simulation correctly predicts the
transition boundaries of wavy stratified to stratified mixed flow.
Other transition boundaries are yet to be simulated. Simulated data
has been validated with our own experimental results.
Abstract: Unmanned Aerial Vehicles (UAVs) have gained tremendous importance, in both Military and Civil, during first decade of this century. In a UAV, onboard computer (autopilot) autonomously controls the flight and navigation of the aircraft. Based on the aircraft role and flight envelope, basic to complex and sophisticated controllers are used to stabilize the aircraft flight parameters. These controllers constitute the autopilot system for UAVs. The autopilot systems, most commonly, provide lateral and longitudinal control through Proportional-Integral-Derivative (PID) controllers or Phase-lead or Lag Compensators. Various techniques are commonly used to ‘tune’ gains of these controllers. Some techniques used are, in-flight step-by-step tuning, software-in-loop or hardware-in-loop tuning methods. Subsequently, numerous in-flight tests are required to actually ‘fine-tune’ these gains. However, an optimization-based tuning of these PID controllers or compensators, as presented in this paper, can greatly minimize the requirement of in-flight ‘tuning’ and substantially reduce the risks and cost involved in flight-testing.
Abstract: Schools today face ever-increasing demands in their attempts to ensure that students are well equipped to enter the workforce and navigate a complex world. Research indicates that computer technology can help support learning, implementation of various experiments or learning games, and that it is especially useful in developing the higher-order skills of critical thinking, observation, comprehension, implementation, comparison, analysis and active attention to activities such as research, field work, simulations and scientific inquiry. The ICT in education supports the learning procedure by enabling it to be more flexible and effective, create a rich and attractive training environment and equip the students with knowledge and potential useful for the competitive social environment in which they live. This paper presents the design, the development, and the results of the evaluation analysis of an interactive educational game which using real electric vehicles - toys (material) on a toy race track. When the game starts each student selects a specific vehicle toy. Then students are answering questionnaires in the computer. The vehicles' speed is related to the percentage of right answers in a multiple choice questionnaire (software). Every question has its own significant value depending of the different level of questionnaire. Via the developed software, each right or wrong answers in questionnaire increase or decrease the real time speed of their vehicle toys. Moreover the rate of vehicle's speed increase or decrease depends on the difficulty level of each question. The aim of the work is to attract the student’s interest in a learning process and also to improve their scores. The developed real time game was tested using independent populations of students of age groups: 8-10, 11-14, 15-18 years. Standard educational and statistical analysis tools were used for the evaluation analysis of the game. Results reveal that students using the developed real time control game scored much higher (60%) than students using a traditional simulation game on the same questionnaire. Results further indicate that student's interest in repeating the developed real time control gaming was far higher (70%) than the interest of students using a traditional simulation game.
Abstract: In Egypt, the concept of Asset Management (AM) is
new; however, the need for applying it has become crucial because
deteriorating or losing an asset is unaffordable in a developing
country like Egypt. Therefore the current study focuses on
educational buildings as one of the most important assets regarding
planning, building, operating and maintenance expenditures. The
main objective of this study is to develop a SAMF for educational
buildings in Egypt. The General Authority for Educational Buildings
(GAEB) was chosen as a case study of the current research as it
represents the biggest governmental organization responsible for
planning, operating and maintaining schools in Egypt. To achieve the
research objective, structured interviews were conducted with senior
managers of GAEB using a pre designed questionnaire to explore the
current practice of AM. Gab analysis technique was applied against
best practices compounded from a vast literature review to identify
gaps between current practices and the desired one. The previous
steps mainly revealed; limited knowledge about strategic asset
management, no clear goals, no training, no real risk plan and lack of
data, technical and financial resources. Based on the findings, a
SAMF for GAEB was introduced and Framework implementation
steps and assessment techniques were explained in detail.
Abstract: Finding suitable non-supersingular elliptic curves for
pairing-based cryptosystems becomes an important issue for the
modern public-key cryptography after the proposition of id-based
encryption scheme and short signature scheme. In previous work
different algorithms have been proposed for finding such elliptic
curves when embedding degree k ∈ {3, 4, 6} and cofactor h ∈ {1, 2, 3,
4, 5}. In this paper a new method is presented to find more
non-supersingular elliptic curves for pairing-based cryptosystems with
general embedding degree k and large values of cofactor h. In
addition, some effective parameters of these non-supersingular elliptic
curves are provided in this paper.
Abstract: Tufting carpet is a very suitable substrate for growing
microorganism such as pathogenic microbes, due to the direct touch
with human body, long washing periods and laying on the floor; in
fact there are 3 major problems: To risk human health, Prepare bad
odors and Destruction of the products.. In the presented research, for
investigation of presence most common microbes on polyester
tufting, first goods laid in a public place (in the corridor fair) for 30
days and the existence of some microbes were investigate on it with
two methods of enrichment in nutrient environments such as
thioglycolate and noutrunt brath, and shake the dust off the polyester
tufting onto cultivation mediums such as blood agar and noutrunt
agar. After the microorganism colonics are grown, the colonies were
separated and six microbial tests such as cataloes and sitrat were
carried out in five phases on the colonics for identifying the varieties
of bacteria. As a result of tests, 5 type of bacteria, such as
Escherichia coli, staphylococcus saprophytic as were identified. Each
of the mentioned bacteria can be seriously harmful for the heath of
human.
Abstract: This paper proposes a model of adding relations between
members of the same level in a pyramid organization structure
which is a complete K-ary tree such that the communication of
information between every member in the organization becomes the
most efficient. When edges between one node and every other node
with the same depth N in a complete K-ary tree of height H are
added, an optimal depth N* = H is obtained by minimizing the total
path length which is the sum of lengths of shortest paths between
every pair of all nodes.
Abstract: The excessive use of agricultural pesticides and the
resulting contamination of food and beds of rivers have been a
recurring problem nowadays. Some of these substances can cause
changes in endocrine balance and impair reproductive function of
human and animal population. In the present study, we evaluated the
possible effects of the fungicide cuprous copper oxide Sandoz® on
pregnant Wistar rats. They received a daily oral administration of 103
or 3.103 mg/kg of the fungicide from the 6th to the 15th day of
gestation. On day 21 of gestation, the maternal and fetal toxicity
parameters and indices were determined. The administration of
cuprous oxide (Copper Sandoz) in Wistar rats, the period of
organogenesis, revealed no evidence of maternal toxicity or embryo
at the studied doses.
Abstract: This paper proposed classification models that would
be used as a proxy for hard disk drive (HDD) functional test equitant
which required approximately more than two weeks to perform the
HDD status classification in either “Pass" or “Fail". These models
were constructed by using committee network which consisted of a
number of single neural networks. This paper also included the
method to solve the problem of sparseness data in failed part, which
was called “enforce learning method". Our results reveal that the
constructed classification models with the proposed method could
perform well in the sparse data conditions and thus the models,
which used a few seconds for HDD classification, could be used to
substitute the HDD functional tests.
Abstract: The purpose of this article is to propose a model designed to achieve Total Knowledge Transfer in the public health sector. The Total Knowledge Transfer Model integrated four essential organizational factors which have been under examined in totality in the literature. The research design was inductive in nature and used a case study for accomplishing the research objectives. The researcher investigated the factors that created a base to design a framework for total knowledge transfer in the public health sector. The results of this study are drawn from a fairly large sample in only two hospitals. A further research can be conducted to cover more responses from a wider health sector. The Total Knowledge Transfer Model is essential to improve the transfer and application of total common health knowledge.
Abstract: Slag sample from copper smelting operation in a
water jacket furnace from DRC plant was used. The study intends to
determine the effect of cooling in the extraction of base metals. The
cooling methods investigated were water quenching, air cooling and
furnace cooling. The latter cooling ways were compared to the
original as received slag. It was observed that, the cooling rate of the
slag affected the leaching of base metals as it changed the phase
distribution in the slag and the base metals distribution within the
phases. It was also found that fast cooling of slag prevented
crystallization and produced an amorphous phase that encloses the
base metals. The amorphous slags from the slag dumps were more
leachable in acidic medium (HNO3) which leached 46%Cu, 95% Co,
85% Zn, 92% Pb and 79% Fe with no selectivity at pH0, than in
basic medium (NH4OH). The leachability was vice versa for the
modified slags by quenching in water which leached 89%Cu with a
high selectivity as metal extractions are less than 1% for Co, Zn, Pb
and Fe at ambient temperature and pH12. For the crystallized slags,
leaching of base metals increased with the increase of temperature
from ambient temperature to 60°C and decreased at the higher
temperature of 80°C due to the evaporation of the ammonia solution
used for basic leaching, the total amounts of base metals that were
leached in slow cooled slags were very low compared to the
quenched slag samples.