Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: Folic acid (FA) is known to be an important
supplement to prevent neural tube defect (NTD) in pregnant women.
Similar to some commercial formulations, sodium bicarbonate
solution is used as a solvent for FA. This work uses the antisolvent
vapour precipitation (AVP), incorporating ethanol vapour as the
convective drying medium in place of air to produce branch-like
micro-structure FA particles. Interestingly, the dissolution rate of the
resultant particle is 2-3 times better than the particle produce from
conventional air drying due to the higher surface area of particles
produced. The higher dissolution rate could possibly improve the
delivery and absorption of FA in human body. This application could
potentially be extended to other commercial products, particularly in
less soluble drugs to improve its solubility.
Abstract: Metallic foams have good potential for lightweight
structures for impact and blast mitigation. Therefore it is important to
find out the optimized foam structure (i.e. cell size, shape, relative
density, and distribution) to maximise energy absorption. In this
paper, quasistatic compression and microstructural characterization
of closed-cell aluminium foams of different pore size and cell
distributions have been carried out. We present results for two
different aluminium metal foams of density 0.49-0.51 g/cc and 0.31-
0.34 g/cc respectively that have been tested in quasi-static
compression. The influence of cell geometry and cell topology on
quasistatic compression behaviour has been investigated using optical
microscope and computed tomography (micro-CT) analysis. It is
shown that the deformation is not uniform in the structure and
collapse begins at the weakest point.
Abstract: The detection of environmental gases, 12CO2, 13CO2,
and CH4, using near-infrared semiconductor lasers with a short
laser path length is studied by means of wavelength-modulation
spectroscopy. The developed system is compact and has high
sensitivity enough to detect the absorption peaks of isotopic 13CO2
of a 3-% CO2 gas at 2 μm with a path length of 2.4 m, where
its peak size is two orders of magnitude smaller than that of the
ordinary 12CO2 peaks. In addition, the detection of 12CO2 peaks of
a 385-ppm (0.0385-%) CO2 gas in the air is made at 2 μm with a
path length of 1.4 m. Furthermore, in pursuing the detection of an
ancient environmental CH4 gas confined to a bubble in ice at the
polar regions, measurements of the absorption spectrum for a trace
gas of CH4 in a small area are attempted. For a 100-% CH4 gas
trapped in a ∼ 1 mm3 glass container, the absorption peaks of CH4
are obtained at 1.65 μm with a path length of 3 mm, and also the
gas pressure is extrapolated from the measured data.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: We have studied a method to widen the spectrum
of optical pulses that pass through an InGaAsP waveguide for
application to broadband optical communication. In particular, we
have investigated the competitive effect between spectral broadening
arising from nonlinear refraction (optical Kerr effect) and shrinking
due to two photon absorption in the InGaAsP waveguide with
χ(3) nonlinearity. The shrunk spectrum recovers broadening by
the enhancement effect of the nonlinear refractive index near the
bandgap of InGaAsP with a bandgap wavelength of 1490 nm. The
broadened spectral width at around 1525 nm (196.7 THz) becomes
10.7 times wider than that at around 1560 nm (192.3 THz) without
the enhancement effect, where amplified optical pulses with a pulse
width of ∼ 2 ps and a peak power of 10 W propagate through a
1-cm-long InGaAsP waveguide with a cross-section of 4 (μm)2.
Abstract: Photoacoustic imaging (PAI) is a non-invasive and
non-ionizing imaging modality that combines the absorption contrast
of light with ultrasound resolution. Laser is used to deposit optical
energy into a target (i.e., optical fluence). Consequently, the target
temperature rises, and then thermal expansion occurs that leads to
generating a PA signal. In general, most image reconstruction
algorithms for PAI assume uniform fluence within an imaging object.
However, it is known that optical fluence distribution within the
object is non-uniform. This could affect the reconstruction of PA
images. In this study, we have investigated the influence of optical
fluence distribution on PA back-propagation imaging using finite
element method. The uniform fluence was simulated as a triangular
waveform within the object of interest. The non-uniform fluence
distribution was estimated by solving light propagation within a
tissue model via Monte Carlo method. The results show that the PA
signal in the case of non-uniform fluence is wider than the uniform
case by 23%. The frequency spectrum of the PA signal due to the
non-uniform fluence has missed some high frequency components in
comparison to the uniform case. Consequently, the reconstructed
image with the non-uniform fluence exhibits a strong smoothing
effect.
Abstract: Two new metal-based anticancer chemotherapeutic
agents, [(Ph2Sn)2(HGuO)2(phen)Cl2] 1 and [(Ph3Sn)(HGuO)(phen)]-
Cl.CH3OH.H2O 2, were designed, prepared and characterized by
analytical and spectral (IR, ESI-Mass, 1H, 13C and 119Sn NMR)
techniques. The proposed geometry of Sn(IV) in 1 and 2 is distorted
octahedral and distorted trigonal-bipyramidal, respectively. Both 1
and 2 exhibit potential cytotoxicity in vitro against MCF-7, HepG-2
and DU-145 cell lines. The intrinsic binding constant (Kb) values of 1
(2.33 × 105 M-1) and 2 (2.46 × 105 M-1) evaluated from UV-Visible
absorption studies suggest non-classical electrostatic mode of
interaction via phosphate backbone of DNA double helix. The Stern-
Volmer quenching constant (Ksv) of 1 (9.74 × 105 M-1) and 2 (2.9 ×
106 M-1) determined by fluorescence studies suggests the groove
binding and intercalation mode for 1 and 2, respectively. Effective
cleavage of pBR322 DNA is induced by 1.Their interaction with
DNA of cancer cells may account for potency.
Abstract: Various biomass based resources, which can be used
as an extender, or a complete substitute of diesel fuel may have very
significant role in the development of agriculture, industrial and
transport sectors in the energy crisis. Use of Karanja oil methyl ester
biodiesel in a CI DI engine was found highly compatible with engine
performance along with lower exhaust emission as compared to
diesel fuel but with slightly higher NOx emission and low wear
characteristics. The combustion related properties of vegetable oils
are somewhat similar to diesel oil. Neat vegetable oils or their blends
with diesel, however, pose various long-term problems in
compression ignition engines. These undesirable features of
vegetable oils are because of their inherent properties like high
viscosity, low volatility, and polyunsaturated character. Pongamia
methyl ester (PME) was prepared by transesterification process using
methanol for long term engine operations. The physical and
combustion-related properties of the fuels thus developed were found
to be closer to that of the diesel. A neat biodiesel (PME) was selected
as a fuel for the tribological study of biofuels.
Two similar new engines were completely disassembled and
subjected to dimensioning of various vital moving parts and then
subjected to long-term endurance tests on neat biodiesel and diesel
respectively. After completion of the test, both the engines were
again disassembled for physical inspection and wear measurement of
various vital parts. The lubricating oil samples drawn from both
engines were subjected to atomic absorption spectroscopy (AAS) for
measurement of various wear metal traces present. The additional
lubricating property of biodiesel fuel due to higher viscosity as
compared to diesel fuel resulted in lower wear of moving parts and
thus improved the engine durability with a bio-diesel fuel. Results
reported from AAS tests confirmed substantially lower wear and thus
improved life for biodiesel operated engines.
Abstract: This paper presents breast cancer detection by
observing the specific absorption rate (SAR) intensity for
identification tumor location, the tumor is identified in coordinates
(x,y,z) system. We examined the frequency between 4-8 GHz to look
for the most appropriate frequency. Results are simulated in
frequency 4-8 GHz, the model overview include normal breast with
50 mm radian, 5 mm diameter of tumor, and ultra wideband (UWB)
bowtie antenna. The models are created and simulated in CST
Microwave Studio. For this simulation, we changed antenna to 5
location around the breast, the tumor can be detected when an
antenna is close to the tumor location, which the coordinate of
maximum SAR is approximated the tumor location. For reliable, we
experiment by random tumor location to 3 position in the same size
of tumor and simulation the result again by varying the antenna
position in 5 position again, and it also detectable the tumor position
from the antenna that nearby tumor position by maximum value of
SAR, which it can be detected the tumor with precision in all
frequency between 4-8 GHz.
Abstract: Single-phase, high band gap energy Zn0.5Mg0.5O films were grown under oxygen pressure, using pulse laser deposition with a Zn0.5Mg0.5O target. Structural characterization studies revealed that the crystal structures of the ZnX-1MgXO films could be controlled via changes in the oxygen pressure. TEM analysis showed that the thickness of the deposited Zn1-xMgxO thin films was 50–75 nm. As the oxygen pressure increased, we found that one axis of the crystals did not show a very significant increase in the crystallization compared with that observed at low oxygen pressure. The X-ray diffraction peak intensity for the hexagonal-ZnMgO (002) plane increased relative to that for the cubic-ZnMgO (111) plane. The corresponding c-axis of the h-ZnMgO lattice constant increased from 5.141 to 5.148 Å, and the a-axis of the c-ZnMgO lattice constant decreased from 4.255 to 4.250 Å. EDX analysis showed that the Mg content in the mixed-phase ZnMgO films decreased significantly, from 54.25 to 46.96 at.%. As the oxygen pressure was increased from 100 to 150 mTorr, the absorption edge red-shifted from 3.96 to 3.81 eV; however, a film grown at the highest oxygen pressure tested here (200 mTorr).
Abstract: A study was conducted in May to July 2013 with the aim of determination of heavy metal concentration in orchard area. 60 samples were collected and analyzed for Cadmium (Cd), Copper (Cu), Lead (Pb), and Zinc (Zn) by Atomic Absorption Spectrophotometer (AAS).
The heavy metal concentrations in sediment of orchards, that use chemical for Cd (1.13 ± 0.26 mg/l), Cu (8.00 ± 1.05 mg/l), Pb (13.16 ± 2.01) and Zn (37.41 ± 3.20 mg/l). The heavy metal concentrations in sediment of the orchards, that do not use chemical for Cd (1.28 ± 0.50 mg/l), Cu (7.60 ± 1.20 mg/l), Pb (29.87 ± 4.88) and Zn (21.79 ± 2.98 mg/l). Statistical analysis between heavy metal in sediment from the orchard, that use chemical and the orchard, that not use chemical were difference statistic significant of 0.5 level of significant for Cd and Pb while no statistically difference for Cu and Zn.
Abstract: This research aims to study the Zinc (Zn) concentration in fine particulate matter on Rajchawithee roadside in rush hour. 30 Samples were collected in Jun to August 2013 by 8 stage non-avaible cascade impactor. Each samples (filter paper) were digest with nitric acid and analyed by atomic absorption spectrophotometer for Zinc determination. The highest value for the mean fraction (18.00 ± 9.28%) is the size 9.0 – 110.0 micron follow by the range 3.3 – 4.7 micron (14.77 ± 14.66 %) and 1.1 – 2.1 micron (14.01 ± 11.77 %). The concentration of Zn in the particulate matter of range 0.43 – 0.7mm, 0.7 – 1.1 mm, 1.1 – 2.1 mm, 2.1 – 3.3 mm, 3.3 – 4.7 mm, 4.7 – 5.8 mm, 5.8 – 9.0 mm, 9.0 – 10.0 mm, were 41.56 – 217.62 mg/m3 (175.86 ±32.25 mg/m3), 152.60 – 217.24 mg/m3 (187.71 ± 17.42 mg/m3), 142.90 – 214.67 mg/m3(180.95 ± 18.71 mg/m3), 155.48 – 218.19 mg/m3(183.22 ± 19.94 mg/m3), 151.72 – 217.39 mg/m3(181.85 ± 17.57 mg/m3), 133.86 – 220.17 mg/m3 (178.78 ± 23.45 mg/m3), 160.00 – 220.35 mg/m3 (182.58 ± 18.08 mg/m3), 153.30 – 226.70 mg/m3 (181.52 ± 20.05 mg/m3), respectively. The Zn concentration in each size of particulate matter was not statistically significant different (p > .005)
Abstract: Diverse contaminants released into the environment through progress of urbanization and industrialization adversely affect human health. Among various sources of contaminants, especially, in big cities, automobiles play a significant role in aggravating the pollution. Various pollutants viz., heavy metals (Pb, Mn, Ni, Zn, As, Hg, Cd) and Polyaromatic hydrocarbons (Benzo-a-pyrene, fluoranthene, pyrene, benzo-b-anthracene, benzo-b-fluoranthene, acenaphthylene, fluorine, phenantherene, anthracene, chrysene, benzo-k-fluoranthene, benzo-e-pyrene, indenol-1,2,3-cd-pyrene, dibenzo-a,h-anthracene, benzo-ghi-perylene) are released by vehicles. Further, these pollutants are expected to cause severe mutagenic, genotoxic and carcinogenic effects. Considering this, many authors monitored the levels of pollution in roadside soil, water and plants. The present review focuses upon the analysis and effects of heavy metals and polycyclic aromatic hydrocarbons from the roadside samples.
Abstract: Utilizing solar energy in producing electricity can minimize environmental pollution generated by fossil fuel in producing electricity. Our research was base on the extraction of dye from Roystonea regia fruit by using methanol as solvent. The dye extracts were used as sensitizers in Dye-sensitized solar cell (DSSCs). Study was done on the electrical properties from the extracts of Roystonea regia fruit as Dye-sensitized solar cell (DSSCs). The absorptions of the extracts and extracts with dye were determined at different wavelengths (350-1000nm). Absorption peak was observed at 1.339 at wavelength 400nm. The obtained values for methanol extract Roystonea regia extract are, Imp = 0.015mA, Vmp = 12.0mV, fill factor = 0.763, Isc= 0.018 mA and Voc = 13.1 mV and efficiency of 0.32%. .The phytochemical screening was taken and it was observed that Roystonea regia extract contained less of anthocyanin compared to flavonoids. The nanostructured dye sensitized solar cell (DSSC) will provide economically credible alternative to present day silicon p–n junction photovoltaic.
Abstract: This paper is an attempt to describe some of the results that had been found through a journey of study in the field of particle physics. This study consists of two parts, one about the measurement of the cross section of the decay of the Z particle in two electrons, and the other deals with the measurement of the cross section of the multi-photon absorption process using a beam of Laser in the Liquid Argon Time Projection Chamber.
The first part of the paper concerns the results based on the analysis of a data sample containing 8120 ee candidates to reconstruct the mass of the Z particle for each event where each event has an ee pair with PT(e) > 20GeV, and η(e) < 2.5. Monte Carlo templates of the reconstructed Z particle were produced as a function of the Z mass scale. The distribution of the reconstructed Z mass in the data was compared to the Monte Carlo templates, where the total cross section is calculated to be equal to 1432pb.
The second part concerns the Liquid Argon Time Projection Chamber, LAr TPC, the results of the interaction of the UV Laser, Nd-YAG with λ= 266mm, with LAr and through the study of the multi-photon ionization process as a part of the R&D at Bern University. The main result of this study was the cross section of the process of the multi-photon ionization process of the LAr, σe = 1.24±0.10stat±0.30sys.10 -56cm4.
Abstract: Stoneware clay, fired clay (as a grog), calcite waste and class C fly ash in various mixing rations were the basic raw materials for the mixture for production of dry pressed ceramic tiles. Mechanical properties (water absorption, bulk density, apparent porosity, flexural strength) as well as mineralogical composition were studied on samples with different source of calcium oxide after firing at 900, 1000, 1100 and 1200°C. It was found that samples with addition of calcite waste contain dmisteinbergit and anorthite. This minerals help to improve the strength of the body and reduce porosity fired at lower temperatures. Class C fly ash has not significantly influence on properties of the fired body as calcite waste.
Abstract: The problem of magnetohydrodynamics boundary layer flow and heat transfer on a permeable stretching surface in a second grade nanofluid under the effect of heat generation and partial slip is studied theoretically. The Brownian motion and thermophoresis effects are also considered. The boundary layer equations governed by the PDE’s are transformed into a set of ODE’s with the help of local similarity transformations. The differential equations are solved by variational finite element method. The effects of different controlling parameters on the flow field and heat transfer characteristics are examined. The numerical results for the dimensionless velocity, temperature and nanoparticle volume fraction as well as the reduced Nusselt and Sherwood number have been presented graphically. The comparison confirmed excellent agreement. The present study is of great interest in coating and suspensions, cooling of metallic plate, oils and grease, paper production, coal water or coal-oil slurries, heat exchangers technology, materials processing exploiting.
Abstract: The acid attack on cement mortars modified with rubber aggregates and EVA polymer binder was studied. Mortar specimens were prepared using a type CEM I 42.5 Portland cement and siliceous sand, as well as by substituting 25% of sand with shredded used automobile tires, and by adding EVA polymer in two percentages (5% and 10% of cement mass). Some specimens were only air cured, at laboratory conditions, and their compressive strength and water absorption were determined. The rest specimens were stored in acid solutions (HCl, H2SO4, HNO3) after 28 days of initial curing, and stored at laboratory temperature. Compressive strength tests, mass measurements and visual inspection took place for 28 days. Compressive strength and water absorption of the air-cured specimens were significantly decreased when rubber aggregates are used. The addition of EVA polymer further reduced water absorption, while had no important impact on strength. Compressive strength values were affected in a greater extent by hydrochloric acid solution, followed by sulfate and nitric acid solutions. The addition of EVA polymer decreased compressive strength loss for the specimens with rubber aggregates stored in hydrochloric and nitric acid solutions. The specimens without polymer binder showed similar mass loss, which was higher in sulfate acid solution followed by hydrochloric and nitric acid solutions. The use of EVA polymer delayed mass loss, while its content did not affect it significantly.
Abstract: Construction industry in Greece consumes annually
more than 25 million tons of natural aggregates originating mainly
from quarries. At the same time, more than 2 million tons of
construction and demolition waste are deposited every year, usually
without control, therefore increasing the environmental impact of this
sector. A potential alternative for saving natural resources and
minimize landfilling, could be the recycling and re-use of Concrete
and Demolition Waste (CDW) in concrete production. Moreover, in
order to conform to the European legislation, Greece is obliged to
recycle non-hazardous construction and demolition waste to a
minimum of 70% by 2020. In this paper characterization of recycled
materials - commercially and laboratory produced, coarse and fine,
Recycled Concrete Aggregates (RCA) - has been performed. Namely,
X-Ray Fluorescence and X-ray diffraction (XRD) analysis were used
for chemical and mineralogical analysis respectively. Physical
properties such as particle density, water absorption, sand equivalent
and resistance to fragmentation were also determined. This study,
first time made in Greece, aims at outlining the differences between
RCA and natural aggregates and evaluating their possible influence
in concrete performance. Results indicate that RCA’s chemical
composition is enriched in Si, Al, and alkali oxides compared to
natural aggregates. X-ray diffraction (XRD) analyses results
indicated the presence of calcite, quartz and minor peaks of mica and
feldspars. From all the evaluated physical properties of coarse RCA,
only water absorption and resistance to fragmentation seem to have a
direct influence on the properties of concrete. Low Sand Equivalent
and significantly high water absorption values indicate that fine
fractions of RCA cannot be used for concrete production unless
further processed. Chemical properties of RCA in terms of water
soluble ions are similar to those of natural aggregates. Four different
concrete mixtures were produced and examined, replacing natural
coarse aggregates with RCA by a ratio of 0%, 25%, 50% and 75%
respectively. Results indicate that concrete mixtures containing
recycled concrete aggregates have a minor deterioration of their
properties (3-9% lower compression strength at 28 days) compared to
conventional concrete containing the same cement quantity.