Abstract: Based on the thermodynamic theory, the dependence of
sublimation energy of metal on temperature and pressure is discussed,
and the results indicate that the sublimation energy decreases linearly
with the increase of temperature and pressure. Combined with this
result, the blow-off impulse of aluminum induced by pulsed X-ray is
simulated by smoothed particle hydrodynamics (SPH) method. The
numerical results show that, while the change of sublimation energy
with temperature and pressure is considered, the blow-off impulse of
aluminum is larger than the case that the sublimation energy is
assumed to be a constant.
Abstract: In this paper, we propose a side-peak cancellation
scheme for code acquisition of composite binary offset carrier
(CBOC) signals. We first model the family of CBOC signals in a
generic form, and then, propose a side-peak cancellation scheme
by combining correlation functions between the divided sub-carrier
and received signals. From numerical results, it is shown that the
proposed scheme removes the side-peak completely, and moreover,
the resulting correlation function demonstrates the better power ratio
performance than the CBOC autocorrelation.
Abstract: A bird strike can cause damage to stationary and
rotating aircraft engine parts, especially the engine fan. This paper
presents a bird strike simulated by blocking four stator blade
passages. It includes the numerical results of the unsteady lowfrequency
aerodynamic forces and the aeroelastic behaviour caused
by a non-symmetric upstream flow affecting the first two rotor blade
stages in the axial-compressor of a jet engine. The obtained results
show that disturbances in the engine inlet strongly influence the level
of unsteady forces acting on the rotor blades. With a partially
blocked inlet the whole spectrum of low-frequency harmonics is
observed. Such harmonics can lead to rotor blade damage. The lowfrequency
amplitudes are higher in the first stage rotor blades than in
the second stage. In both rotor blades stages flutter appeared as a
result of bird strike.
Abstract: Along with increasing development of generation of supersonic planes especially fighters and request for increasing the performance and maneuverability scientists and engineers suggested the delta and double delta wing design. One of the areas which was necessary to be researched, was the Aerodynamic review of this type of wings in high angles of attack at low speeds that was very important in landing and takeoff the planes and maneuvers. Leading Edges of the wings,cause the separation flow from wing surface and then formation of powerful vortex with high rotational speed which studing the mechanism and location of formation and also the position of the vortex breakdown in high angles of attack is very important. In this research, a double delta wing with 76o/45o sweep angles at high angle of attack in steady state and incompressible flow were numerically analyzed with Fluent software. With analaysis of the numerical results, we arrived the most important characteristic of the double delta wings which is keeping of lift at high angles of attacks.
Abstract: To understand the seismic behavior of the offshore
structures, the dynamic interaction of the water-structure-soil should
be assessed. In this regard the role of the water dynamic properties in
magnifying or reducing of the effects of earthquake induced motions
on offshore structures haven't been investigated in precise manner in
available literature. In this paper the sea water level fluctuations
effects on the seismic behavior of a sample of offshore structures has
been investigated by emphasizing on the water-structure interaction
phenomenon. For this purpose a two dimensional finite element
model of offshore structures as well as surrounded water has been
developed using ANSYS software. The effect of soil interaction with
embedded pile foundation has been imposed by using a series of
nonlinear springs in horizontal and vertical directions in soil-piles
contact points. In the model, the earthquake induced motions have
been applied on springs and consequently the motions propagated
upward to the structure and surrounded water. As a result of
numerical study, the horizontal deformations of the offshore deck as
well as internal force and buckling coefficient in structural elements
have been recorded and controlled with and without water presence.
In part of study a parametric study has been accomplished on sea
water level fluctuations and effect of this parameter has been studied
on the aforementioned numerical results.
Abstract: A lightpipe is an about 99 percent specular reflective
mirror pipe or duct that is used for the transmission of the daylight
from the outside into a building. The lightpipes are usually used in
the daylighting buildings, in the residential, industrial and
commercial sectors. This paper is about the performances of a
lightpipe installed in a laboratory (3 m x 2.6 m x 3 m) without
windows. The aim is to analyse the luminous intensity distribution
for several sky/sun conditions. The lightpipe was monitored during
the year 2006. The lightpipe is 1 m long and the diameter of the top
collector and of the internal diffuser device is 0.25 m. In the
laboratory there are seven illuminance sensors: one external is
located on the roof of the laboratory and six internal sensors are
connected to a data acquisition system. The internal sensors are
positioned under the internal diffusive device at an height of 0.85 m
from the floor to simulate a working plane. The numerical data are
obtained through a simulation software. This paper shows the
comparison between the experimental and numerical results
concerning the behavior of the lightpipe.
Abstract: In a chirp spread spectrum (CSS) system, the overlap
technique is used for increasing bit rate. More overlaps can offer
higher data throughput; however, they may cause more intersymbol
interference (ISI) at the same time, resulting in serious bit error
rate (BER) performance degradation. In this paper, we perform the
BER analysis and derive a closed form BER expression for the
overlap-based CSS system. The derived BER expression includes
the number of overlaps as a parameter, and thus, would be very
useful in determining the number of overlaps for a specified BER.
The numerical results demonstrate that the BER derived in a closed
form closely agrees with the simulated BER.
Abstract: New regulations and standards for noise emission increasingly compel the automotive firms to make some improvements about decreasing the engine noise. Nowadays, the perforated reactive mufflers which have an effective damping capability are specifically used for this purpose. New designs should be analyzed with respect to both acoustics and back pressure. In this study, a reactive perforated muffler is investigated numerically and experimentally. For an acoustical analysis, the transmission loss which is independent of sound source of the present cross flow, the perforated muffler was analyzed by COMSOL. To be able to validate the numerical results, transmission loss was measured experimentally. Back pressure was obtained based on the flow field analysis and was also compared with experimental results. Numerical results have an approximate error of 20% compared to experimental results.
Abstract: Mathematical and computational modeling of calcium
signalling in nerve cells has produced considerable insights into how
the cells contracts with other cells under the variation of biophysical
and physiological parameters. The modeling of calcium signaling in
astrocytes has become more sophisticated. The modeling effort has
provided insight to understand the cell contraction. Main objective
of this work is to study the effect of voltage gated (Operated)
calcium channel (VOC) on calcium profile in the form of advection
diffusion equation. A mathematical model is developed in the form
of advection diffusion equation for the calcium profile. The model
incorporates the important physiological parameter like diffusion
coefficient etc. Appropriate boundary conditions have been framed.
Finite volume method is employed to solve the problem. A program
has been developed using in MATLAB 7.5 for the entire problem
and simulated on an AMD-Turion 32-bite machine to compute the
numerical results.
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: A highly optimized implementation of binary mixture
diffusion with no initial bulk velocity on graphics processors is
presented. The lattice Boltzmann model is employed for simulating
the binary diffusion of oxygen and nitrogen into each other with
different initial concentration distributions. Simulations have been
performed using the latest proposed lattice Boltzmann model that
satisfies both the indifferentiability principle and the H-theorem for
multi-component gas mixtures. Contemporary numerical
optimization techniques such as memory alignment and increasing
the multiprocessor occupancy are exploited along with some novel
optimization strategies to enhance the computational performance on
graphics processors using the C for CUDA programming language.
Speedup of more than two orders of magnitude over single-core
processors is achieved on a variety of Graphical Processing Unit
(GPU) devices ranging from conventional graphics cards to
advanced, high-end GPUs, while the numerical results are in
excellent agreement with the available analytical and numerical data
in the literature.
Abstract: The present study was provided to examine the
vortical structures generated by two inclined impinging jets with
experimental and numerical investigations. The jets are issuing with a
pitch angle α=40° into a confined quiescent fluid. The experimental
investigation on flow patterns was visualized by using olive particles
injected into the jets illuminated by Nd:Yag laser light to reveal the
finer details of the confined jets interaction. It was observed that two
counter-rotating vortex pairs (CVPs) were generated in the near
region. A numerical investigation was also performed. First, the
numerical results were validates against the experimental results and
then the numerical model was used to study the effect of section ratio
on the evolution of the CVPs. Our results show promising agreement
with experimental data, and indicate that our model has the potential
to produce useful and accurate data regarding the evolution of CVPs.
Abstract: Economic Load Dispatch (ELD) is a method of determining
the most efficient, low-cost and reliable operation of a power
system by dispatching available electricity generation resources to
supply load on the system. The primary objective of economic
dispatch is to minimize total cost of generation while honoring
operational constraints of available generation resources. In this paper
an intelligent water drop (IWD) algorithm has been proposed to
solve ELD problem with an objective of minimizing the total cost of
generation. Intelligent water drop algorithm is a swarm-based natureinspired
optimization algorithm, which has been inspired from natural
rivers. A natural river often finds good paths among lots of possible
paths in its ways from source to destination and finally find almost
optimal path to their destination. These ideas are embedded into
the proposed algorithm for solving economic load dispatch problem.
The main advantage of the proposed technique is easy is implement
and capable of finding feasible near global optimal solution with
less computational effort. In order to illustrate the effectiveness of
the proposed method, it has been tested on 6-unit and 20-unit test
systems with incremental fuel cost functions taking into account the
valve point-point loading effects. Numerical results shows that the
proposed method has good convergence property and better in quality
of solution than other algorithms reported in recent literature.
Abstract: Unsteady boundary layer flow of an incompressible
micropolar fluid over a stretching sheet when the sheet is stretched in
its own plane is studied in this paper. The stretching velocity is
assumed to vary linearly with the distance along the sheet. Two equal
and opposite forces are impulsively applied along the x-axis so that the
sheet is stretched, keeping the origin fixed in a micropolar fluid. The
transformed unsteady boundary layer equations are solved
numerically using the Keller-box method for the whole transient from
the initial state to final steady-state flow. Numerical results are
obtained for the velocity and microrotation distributions as well as the
skin friction coefficient for various values of the material parameter K.
It is found that there is a smooth transition from the small-time
solution to the large-time solution.
Abstract: An attempt has been made to develop a
seminumerical model to study temperature variations in dermal
layers of human limbs. The model has been developed for two
dimensional steady state case. The human limb has been assumed to
have elliptical cross section. The dermal region has been divided
into three natural layers namely epidermis, dermis and subdermal
tissues. The model incorporates the effect of important physiological
parameters like blood mass flow rate, metabolic heat generation, and
thermal conductivity of the tissues. The outer surface of the limb is
exposed to the environment and it is assumed that heat loss takes
place at the outer surface by conduction, convection, radiation, and
evaporation. The temperature of inner core of the limb also varies at
the lower atmospheric temperature. Appropriate boundary conditions
have been framed based on the physical conditions of the problem.
Cubic splines approach has been employed along radial direction and
Fourier series along angular direction to obtain the solution. The
numerical results have been computed for different values of
eccentricity resembling with the elliptic cross section of the human
limbs. The numerical results have been used to obtain the
temperature profile and to study the relationships among the various
physiological parameters.
Abstract: A numerical study on the turbulent flow and heat
transfer characteristics in the rectangular channel with different types
of baffles is carried out. The inclined baffles have the width of 19.8
cm, the square diamond type hole having one side length of 2.55 cm,
and the inclination angle of 5o. Reynolds number is varied between
23,000 and 57,000. The SST turbulence model is applied in the
calculation. The validity of the numerical results is examined by the
experimental data. The numerical results of the flow field depict that
the flow patterns around the different baffle type are entirely different
and these significantly affect the local heat transfer characteristics.
The heat transfer and friction factor characteristics are significantly
affected by the perforation density of the baffle plate. It is found that
the heat transfer enhancement of baffle type II (3 hole baffle) has the
best values.
Abstract: The IEEE802.16 standard which has emerged as
Broadband Wireless Access (BWA) technology, promises to deliver
high data rate over large areas to a large number of subscribers in the
near future. This paper analyze the effect of overheads over capacity
of downlink (DL) of orthogonal frequency division multiple access
(OFDMA)–based on the IEEE802.16e mobile WiMAX system with
and without overheads. The analysis focuses in particular on the
impact of Adaptive Modulation and Coding (AMC) as well as
deriving an algorithm to determine the maximum numbers of
subscribers that each specific WiMAX sector may support. An
analytical study of the WiMAX propagation channel by using Cost-
231 Hata Model is presented. Numerical results and discussion
estimated by using Matlab to simulate the algorithm for different
multi-users parameters.
Abstract: Malaria is transmitted to the human by biting of
infected Anopheles mosquitoes. This disease is a serious, acute and
chronic relapsing infection to humans. Fever, nausea, vomiting, back
pain, increased sweating anemia and splenomegaly (enlargement of
the spleen) are the symptoms of the patients who infected with this
disease. It is caused by the multiplication of protozoa parasite of the
genus Plasmodium. Plasmodium falciparum, Plasmodium vivax,
Plasmodium malariae and Plasmodium ovale are the four types of
Plasmodium malaria. A mathematical model for the transmission of
Plasmodium Malaria is developed in which the human and vector
population are divided into two classes, the susceptible and the
infectious classes. In this paper, we formulate the dynamical model
of Plasmodium falciparum and Plasmodium vivax malaria. The
standard dynamical analysis is used for analyzing the behavior for
the transmission of this disease. The Threshold condition is found
and numerical results are shown to confirm the analytical results.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.