Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: State-dependent Riccati equation based controllers are
becoming increasingly popular because of having attractive
properties like optimality, stability and robustness. This paper focuses
on the design of a roll autopilot for a fin stabilized and canard
controlled 122mm artillery rocket using state-dependent Riccati
equation technique. Initial spin is imparted to rocket during launch
and it quickly decays due to straight tail fins. After the spin phase, the
roll orientation of rocket is brought to zero with the canard deflection
commands generated by the roll autopilot. Roll autopilot has been
developed by considering uncoupled roll, pitch and yaw channels.
The canard actuator is modeled as a second-order nonlinear system.
Elements of the state weighing matrix for Riccati equation have been
chosen to be state dependent to exploit the design flexibility offered
by the Riccati equation technique. Simulation results under varying
conditions of flight demonstrate the wide operating range of the
proposed autopilot.
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: A 7-step method (with 25 sub-steps) to assess risk of
air pollutants is introduced. These steps are: pre-considerations,
sampling, statistical analysis, exposure matrix and likelihood, doseresponse
matrix and likelihood, total risk evaluation, and discussion
of findings. All mentioned words and expressions are wellunderstood;
however, almost all steps have been modified, improved,
and coupled in such a way that a comprehensive method has been
prepared. Accordingly, the SADRA (Statistical Analysis-Driven Risk
Assessment) emphasizes extensive and ongoing application of
analytical statistics in traditional risk assessment models. A Sulfur
Dioxide case study validates the claim and provides a good
illustration for this method.
Abstract: A new paradigm for software design and development models software by its business process, translates the model into a process execution language, and has it run by a supporting execution engine. This process-oriented paradigm promotes modeling of software by less technical users or business analysts as well as rapid development. Since business process models may be shared by different organizations and sometimes even by different business domains, it is interesting to apply a technique used in traditional software component technology to design reusable business processes. This paper discusses an approach to apply a technique for software component fabrication to the design of process-oriented software units, called process components. These process components result from decomposing a business process of a particular application domain into subprocesses with an aim that the process components can be reusable in different process-based software models. The approach is quantitative because the quality of process component design is measured from technical features of the process components. The approach is also strategic because the measured quality is determined against business-oriented component management goals. A software tool has been developed to measure how good a process component design is, according to the required managerial goals and comparing to other designs. We also discuss how we benefit from reusable process components.
Abstract: The effect of chemical treatment in CdCl2 and thermal
annealing in 400°C, on the defect structures of potentially useful
ZnS\CdS solar cell thin films deposited onto quartz substrate and
prepared by vacuum deposition method was studied using the
Thermoluminesence (TL) techniques. A series of electron and hole
traps are found in the various deposited samples studied. After
annealing, however, it was observed that the intensity and activation
energy of TL signal increases with loss of the low temperature
electron traps.
Abstract: Adsorption of Toluidine blue dye from aqueous solutions onto Neem Leaf Powder (NLP) has been investigated. The surface characterization of this natural material was examined by Particle size analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) spectroscopy and X-Ray Diffraction (XRD). The effects of process parameters such as initial concentration, pH, temperature and contact duration on the adsorption capacities have been evaluated, in which pH has been found to be most effective parameter among all. The data were analyzed using the Langmuir and Freundlich for explaining the equilibrium characteristics of adsorption. And kinetic models like pseudo first- order, second-order model and Elovich equation were utilized to describe the kinetic data. The experimental data were well fitted with Langmuir adsorption isotherm model and pseudo second order kinetic model. The thermodynamic parameters, such as Free energy of adsorption (AG"), enthalpy change (AH') and entropy change (AS°) were also determined and evaluated.
Abstract: Intelligent systems based on machine learning
techniques, such as classification, clustering, are gaining wide spread
popularity in real world applications. This paper presents work on
developing a software system for predicting crop yield, for example
oil-palm yield, from climate and plantation data. At the core of our
system is a method for unsupervised partitioning of data for finding
spatio-temporal patterns in climate data using kernel methods which
offer strength to deal with complex data. This work gets inspiration
from the notion that a non-linear data transformation into some high
dimensional feature space increases the possibility of linear
separability of the patterns in the transformed space. Therefore, it
simplifies exploration of the associated structure in the data. Kernel
methods implicitly perform a non-linear mapping of the input data
into a high dimensional feature space by replacing the inner products
with an appropriate positive definite function. In this paper we
present a robust weighted kernel k-means algorithm incorporating
spatial constraints for clustering the data. The proposed algorithm
can effectively handle noise, outliers and auto-correlation in the
spatial data, for effective and efficient data analysis by exploring
patterns and structures in the data, and thus can be used for
predicting oil-palm yield by analyzing various factors affecting the
yield.
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: The importance of inter-organizational system (IOS)
has been increasingly recognized by organizations. However, IOS
adoption has proved to be difficult and, at this stage, why this is so is
not fully uncovered. In practice, benefits have often remained
concentrated, primarily accruing to the dominant party, resulting in
low rates of adoption and usage, and often culminating in the failure
of the IOS. The main research question is why organizations initiate
or join IOS and what factors influence their adoption and use levels.
This paper reviews the literature on IOS adoption and proposes a
theoretical framework in order to identify the critical factors to
capture a complete picture of IOS adoption. With our proposed
critical factors, we are able to investigate their relative contributions
to IOS adoption decisions. We obtain findings that suggested that
there are five groups of factors that significantly affect the adoption
and use decision of IOS in the Supply Chain Management (SCM)
context: 1) interorganizational context, 2) organizational context, 3)
technological context, 4) perceived costs, and 5) perceived benefits.
Abstract: MABENA model is a complementary model in
comparison with traditional models such as HCMS, CMS and etc.
New factors, which have effects on preparation of strategic plans and
their sequential order in MABENA model is the platform of
presented road map in this paper.Study review shows, factors such as
emerging new critical success factors for strategic planning,
improvement of international strategic models, increasing the
maturity of companies and emerging new needs leading to design a
new model which can be responsible for new critical factors and
solve the limitations of previous strategic management models.
Preparation of strategic planning need more factors than introduced
in traditional models. The needed factors includes determining future
Critical Success Factors and competencies, defining key processes,
determining the maturity of the processes, considering all aspects of
the external environment etc. Description of aforementioned
requirements, the outcomes and their order is developing and
presenting the MABENA model-s road map in this paper. This study
presents a road map for strategic planning of the Iranian
organizations.
Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: Temperature dependence of force of gravitation is one
of the fundamental problems of physics. This problem has got special
value in connection with that the general theory of relativity,
supposing the weakest positive influence of a body temperature on its
weight, actually rejects an opportunity of measurement of negative
influence of temperature on gravity in laboratory conditions. Really,
the recognition of negative temperature dependence of gravitation,
for example, means basic impossibility of achievement of a
singularity («a black hole») at a gravitational collapse. Laboratory
experiments with exact weighing the heated up metal samples,
indicating negative influence temperatures of bodies on their physical
weight are described. Influence of mistakes of measurements is
analyzed. Calculations of distribution of temperature in volume of the
bar, agreed with experimental data of time dependence of weight of
samples are executed. The physical substantiation of negative
temperature dependence of weight of the bodies, based on correlation
of acceleration at thermal movement of micro-particles of a body and
its absolute temperature, are given.
Abstract: This article stands in the context of rural communities
in Brazil, where, like many others emerging countries, the
overwhelming increasing markets and the overcrowded cities are
leaving behind informal settlements based on obsolete agricultural
economies and techniques. The pilot project for the community of
Goiabeira reflects the attempt to imagine a development model that
privileges the actual improvement of living conditions, the education
and training, the social inclusion and participation of the dwellers of
rural communities. Through the inclusion of operative public space,
the aim is for them to become self-sustaining, encouraging the use of
local resources for appropriate architectural, ecological and energy
technologies and devices, that are efficient, affordable and foster
community participation, in the respect of the surrounding
environment.
Abstract: In this study, a reformer model simulation to use
refinery (Farashband refinery, Iran) waste natural gas. In the
petroleum and allied sectors where natural gas is being encountered
(in form of associated gas) without prior preparation for its positive
use, its combustion (which takes place in flares, an equipment through
which they are being disposed) has become a great problem because
of its associated environmental problems in form of gaseous emission.
The proposed model is used to product syngas from waste natural gas.
A detailed steady model described by a set of ordinary differential and
algebraic equations was developed to predict the behavior of the
overall process. The proposed steady reactor model was validated
against process data of a reformer synthesis plant recorded and a good
agreement was achieved. H2/CO ratio has important effect on Fischer-
Tropsch synthesis reactor product and we try to achieve this parameter
with best designing reformer reactor. We study different kind of
reformer reactors and then select auto thermal reforming process of
natural gas in a fixed bed reformer that adjustment H2/CO ratio with
CO2 and H2O injection. Finally a strategy was proposed for prevention
of extra natural gas to atmosphere.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: The recent developments in computing and
communication technology permit to users to access multimedia
documents with variety of devices (PCs, PDAs, mobile phones...)
having heterogeneous capabilities. This diversification of supports
has trained the need to adapt multimedia documents according to
their execution contexts. A semantic framework for multimedia
document adaptation based on the conceptual neighborhood graphs
was proposed. In this framework, adapting consists on finding
another specification that satisfies the target constraints and which is
as close as possible from the initial document. In this paper, we
propose a new way of building the conceptual neighborhood graphs
to best preserve the proximity between the adapted and the original
documents and to deal with more elaborated relations models by
integrating the relations relaxation graphs that permit to handle the
delays and the distances defined within the relations.
Abstract: This paper presents the development of adaptive
distance relay for protection of parallel transmission line with mutual
coupling. The proposed adaptive relay, automatically adjusts its
operation based on the acquisition of the data from distance relay of
adjacent line and status of adjacent line from line circuit breaker IED
(Intelligent Electronic Device). The zero sequence current of the
adjacent parallel transmission line is used to compute zero sequence
current ratio and the mutual coupling effect is fully compensated.
The relay adapts to changing circumstances, like failure in
communication from other relays and non - availability of adjacent
transmission line. The performance of the proposed adaptive relay is
tested using steady state and dynamic test procedures. The fault
transients are obtained by simulating a realistic parallel transmission
line system with mutual coupling effect in PSCAD. The evaluation
test results show the efficacy of adaptive distance relay over the
conventional distance relay.
Abstract: This research proposes a methodology for patent-citation-based technology input-output analysis by applying the patent information to input-output analysis developed for the dependencies among different industries. For this analysis, a technology relationship matrix and its components, as well as input and technology inducement coefficients, are constructed using patent information. Then, a technology inducement coefficient is calculated by normalizing the degree of citation from certain IPCs to the different IPCs (International patent classification) or to the same IPCs. Finally, we construct a Dependency Structure Matrix (DSM) based on the technology inducement coefficient to suggest a useful application for this methodology.