Abstract: This work presents a study on the abrasive water jet
(AWJ) machining. An explicit finite element analysis (FEA) of
single abrasive particle impact on stainless steel 1.4304 (AISI 304) is
conducted. The abrasive water jet machining is modeled by FEA
software ABAQUS/CAE. Shapes of craters in FEM simulation
results were used and compared with the previous experimental and
FEM works by means of crater sphericity. The influence of impact
angle and particle velocity was observed. Adaptive mesh domain is
used to model the impact zone. Results are in good agreement with
those obtained from the experimental and FEM simulation. The
crater-s depth is also obtained for different impact angle and abrasive
particle velocities.
Abstract: A numerical study is made of laminar, unsteady flow
behind a rotationally oscillating circular cylinder using a recently
developed higher order compact (HOC) scheme. The stream function
vorticity formulation of Navier-Stokes (N-S) equations in cylindrical
polar coordinates are considered as the governing equations. The
temporal behaviour of vortex formation and relevant streamline
patterns of the flow are scrutinized over broad ranges of two
externally specified parameters namely dimensionless forced
oscillating frequency Sf and dimensionless peak rotation rate αm for
the Reynolds-s number Re = 200. Excellent agreements are found
both qualitatively and quantitatively with the existing experimental
and standard numerical results.
Abstract: To calculate the temperature distribution of the slab in
a hot rolled reheating furnace a mathematical model has been
developed by considering the thermal radiation in the furnace and
transient conduction in the slab. The furnace is modeled as radiating
medium with spatially varying temperature. Radiative heat flux within
the furnace including the effect of furnace walls, combustion gases,
skid beams and buttons is calculated using the FVM and is applied as
the boundary condition of the transient conduction equation of the
slab. After determining the slab emissivity by comparison between
simulation and experimental work, variation of heating characteristics
in the slab is investigated in the case of changing furnace temperature
with various time and the slab residence time is optimized with this
evaluation.
Abstract: Embedding and extraction of a secret information as
well as the restoration of the original un-watermarked image is
highly desirable in sensitive applications like military, medical, and
law enforcement imaging. This paper presents a novel reversible
data-hiding method for digital images using integer to integer
wavelet transform and companding technique which can embed and
recover the secret information as well as can restore the image to its
pristine state. The novel method takes advantage of block based
watermarking and iterative optimization of threshold for companding
which avoids histogram pre and post-processing. Consequently, it
reduces the associated overhead usually required in most of the
reversible watermarking techniques. As a result, it keeps the
distortion small between the marked and the original images.
Experimental results show that the proposed method outperforms the
existing reversible data hiding schemes reported in the literature.
Abstract: Surveillance system is widely used in the traffic
monitoring. The deployment of cameras is moving toward a
ubiquitous camera (UbiCam) environment. In our previous study, a
novel service, called GPS-VT, was firstly proposed by incorporating
global positioning system (GPS) and visual tracking techniques for
the UbiCam environment. The first prototype is called GODTA
(GPS-based Moving Object Detection and Tracking Approach). For a
moving person carried GPS-enabled mobile device, he can be
tracking when he enters the field-of-view (FOV) of a camera
according to his real-time GPS coordinate. In this paper, GPS-VT
service is applied to the tracking of vehicles. The moving speed of a
vehicle is much faster than a person. It means that the time passing
through the FOV is much shorter than that of a person. Besides, the
update interval of GPS coordinate is once per second, it is
asynchronous with the frame rate of the real-time image. The above
asynchronous is worsen by the network transmission delay. These
factors are the main challenging to fulfill GPS-VT service on a
vehicle.In order to overcome the influence of the above factors, a
back-propagation neural network (BPNN) is used to predict the
possible lane before the vehicle enters the FOV of a camera. Then, a
template matching technique is used for the visual tracking of a target
vehicle. The experimental result shows that the target vehicle can be
located and tracking successfully. The success location rate of the
implemented prototype is higher than that of the previous GODTA.
Abstract: Clearance in the joints of multibody mechanical
systems such as linkage mechanisms and robots is a main source of
vibration, and noise of the whole system, and wear of the joints
themselves. This clearance is an inevitable matter and cannot be
eliminated, since it allows the relative motion between joint
components and make them assemblage. This paper presents an
experimental verification of the obtained simulation results of a slider
– crank mechanism of one clearance revolute joint. The simulation
results are obtained with the aid of CAD and dynamic simulation
softwares, which is an effective method of simulation multibody
systems with clearance joints and have many advantages. The
comparison between both simulation and experimental results shows
that the simulation results are so close to the experimental ones which
proves the accuracy and efficiency of this method of modeling and
simulation of mechanical systems with clearance joints.
Abstract: Theoptimal extraction condition of dried Phaseolus
vulgaris powderwas studied. The three independent variables are raw
material concentration, shaking and centrifugaltime. The dependent
variables are both yield percentage of crude extract and alphaamylase
enzyme inhibition activity. The experimental design was
based on box-behnkendesign. Highest yield percentage of crude
extract could get from extraction condition at concentration of 1, 0,1,
concentration of 0.15 M ,extraction time for 2hour, and
separationtime for60 min. Moreover, the crude extract with highest
alpha-amylase enzyme inhibition activityoccurred by extraction
condition at concentration of 0.10 M, extraction time for 2 min, and
separation time for 45 min
Abstract: Metal matrix composites have been increasingly used
as materials for components in automotive and aerospace industries
because of their improved properties compared with non-reinforced
alloys. During machining the selection of appropriate machining
parameters to produce job for desired surface roughness is of great
concern considering the economy of manufacturing process. In this
study, a surface roughness prediction model using fuzzy logic is
developed for end milling of Al-SiCp metal matrix composite
component using carbide end mill cutter. The surface roughness is
modeled as a function of spindle speed (N), feed rate (f), depth of cut
(d) and the SiCp percentage (S). The predicted values surface
roughness is compared with experimental result. The model predicts
average percentage error as 4.56% and mean square error as 0.0729.
It is observed that surface roughness is most influenced by feed rate,
spindle speed and SiC percentage. Depth of cut has least influence.
Abstract: Machining is an important manufacturing process used to produce a wide variety of metallic parts. Among various machining processes, turning is one of the most important one which is employed to shape cylindrical parts. In turning, the quality of finished product is measured in terms of surface roughness. In turn, surface quality is determined by machining parameters and tool geometry specifications. The main objective of this study is to simultaneously model and optimize machining parameters and tool geometry in order to improve the surface roughness for AISI1045 steel. Several levels of machining parameters and tool geometry specifications are considered as input parameters. The surface roughness is selected as process output measure of performance. A Taguchi approach is employed to gather experimental data. Then, based on signal-to-noise (S/N) ratio, the best sets of cutting parameters and tool geometry specifications have been determined. Using these parameters values, the surface roughness of AISI1045 steel parts may be minimized. Experimental results are provided to illustrate the effectiveness of the proposed approach.
Abstract: XML data consists of a very flexible tree-structure
which makes it difficult to support the storing and retrieving of XML
data. The node numbering scheme is one of the most popular
approaches to store XML in relational databases. Together with the
node numbering storage scheme, structural joins can be used to
efficiently process the hierarchical relationships in XML. However, in
order to process a tree-structured XPath query containing several
hierarchical relationships and conditional sentences on XML data,
many structural joins need to be carried out, which results in a high
query execution cost. This paper introduces mechanisms to reduce the
XPath queries including branch nodes into a much more efficient form
with less numbers of structural joins. A two step approach is proposed.
The first step merges duplicate nodes in the tree-structured query and
the second step divides the query into sub-queries, shortens the paths
and then merges the sub-queries back together. The proposed
approach can highly contribute to the efficient execution of XML
queries. Experimental results show that the proposed scheme can
reduce the query execution cost by up to an order of magnitude of the
original execution cost.
Abstract: The aim of this paper is to experimentally discover the workability coefficient of the Inconel 718 material by using a slide turning machining. Two different types of cutting inserts, one made of carbide and the other one made of ceramic, are being used. The purpose is to compare measured results and recommend the appropriate materials and cutting parameters for a machining of the Inconel 718. Furthermore, the durability of inserts with the chosen wear criterion is being compared for different cutting speeds. Machinability of these materials is a crucial characteristic as it allows us to shorten the technological cycle time and increase the machining productivity. And this is of great importance from an economic point of view.
Abstract: This paper addresses the problem of source separation
in images. We propose a FastICA algorithm employing a modified
Gaussian contrast function for the Blind Source Separation.
Experimental result shows that the proposed Modified Gaussian
FastICA is effectively used for Blind Source Separation to obtain
better quality images. In this paper, a comparative study has been
made with other popular existing algorithms. The peak signal to
noise ratio (PSNR) and improved signal to noise ratio (ISNR) are
used as metrics for evaluating the quality of images. The ICA metric
Amari error is also used to measure the quality of separation.
Abstract: The article deals with experimental and numerical
investigation of axi-symmetric subsonic air to air ejector with
diffuser adapted for boundary layer suction. The diffuser, which is
placed behind the mixing chamber of the ejector, has high divergence
angle and therefore low efficiency. To increase the efficiency, the
diffuser is equipped with slot enabling boundary layer suction. The
effect of boundary layer suction on flow in ejector, static pressure
distribution on the mixing chamber wall and characteristic were
measured and studied numerically. Both diffuser and ejector
efficiency were evaluated. The diffuser efficiency was increased,
however, the efficiency of ejector itself remained low.
Abstract: This research work proposed a study of fruit bruise detection by means of a biospeckle method, selecting the papaya fruit (Carica papaya) as testing body. Papaya is recognized as a fruit of outstanding nutritional qualities, showing high vitamin A content, calcium, carbohydrates, exhibiting high popularity all over the world, considering consumption and acceptability. The commercialization of papaya faces special problems which are associated to bruise generation during harvesting, packing and transportation. Papaya is classified as climacteric fruit, permitting to be harvested before the maturation is completed. However, by one side bruise generation is partially controlled once the fruit flesh exhibits high mechanical firmness. By the other side, mechanical loads can set a future bruise at that maturation stage, when it can not be detected yet by conventional methods. Mechanical damages of fruit skin leave an entrance door to microorganisms and pathogens, which will cause severe losses of quality attributes. Traditional techniques of fruit quality inspection include total soluble solids determination, mechanical firmness tests, visual inspections, which would hardly meet required conditions for a fully automated process. However, the pertinent literature reveals a new method named biospeckle which is based on the laser reflectance and interference phenomenon. The laser biospeckle or dynamic speckle is quantified by means of the Moment of Inertia, named after its mechanical counterpart due to similarity between the defining formulae. Biospeckle techniques are able to quantify biological activities of living tissues, which has been applied to seed viability analysis, vegetable senescence and similar topics. Since the biospeckle techniques can monitor tissue physiology, it could also detect changes in the fruit caused by mechanical damages. The proposed technique holds non invasive character, being able to generate numerical results consistent with an adequate automation. The experimental tests associated to this research work included the selection of papaya fruit at different maturation stages which were submitted to artificial mechanical bruising tests. Damages were visually compared with the frequency maps yielded by the biospeckle technique. Results were considered in close agreement.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually to some extent the effects of blurred edges and jagged artifacts in the image. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to enhance edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (''jaggies'') along the tangent directions. In order to preserve image features such as edges, angles and textures, the nonlinear diffusion coefficients are locally adjusted according to the first and second order directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: When a lightning strike falls near an overhead power
line, the intense electromagnetic field radiated by the current of the
lightning return stroke coupled with power lines and there induced
transient overvoltages, which can cause a back-flashover in electrical
network. The indirect lightning represents a major danger owing to
the fact that it is more frequent than that which results from the direct
strikes.
In this paper we present an analysis of the electromagnetic
coupling between an external electromagnetic field generated by the
lightning and an electrical overhead lines, so we give an important
and original contribution: We are based on our experimental
measurements which we carried in the high voltage laboratories of
EPFL in Switzerland during the last trimester of 2005, on the recent
works of other authors and with our mathematical improvement a
new particular analytical expression of the electromagnetic field
generated by the lightning return stroke was developed and presented
in this paper. The results obtained by this new electromagnetic field
formulation were compared with experimental results and give a
reasonable approach.
Abstract: Materials added to the matrix help improving operating properties of a composite. This experimental study has targeted to investigate this aim where Silicon Oxide particles were added to glass fibre and epoxy resin at an amount of 15% to the main material to obtain a sort of new composite material. Erosive wear behavior of epoxy-resin dipped composite materials reinforced with glass fibre and Silicon Oxide under three different impingement angles (30°, 60° and 90°), three different impact velocities (23, 34 and 53 m/s), two different angular Aluminum abrasive particle sizes (approximately 200 and 400 μm) and the fibre orientation of 45° (45/-45) were investigated. In the test results, erosion rates were obtained as functions of impingement angles, impact velocities, particle sizes and fibre orientation. Moreover, materials with addition of Silicon Oxide filler material exhibited lower wear as compared to neat materials with no added filler material. In addition, SEM views showing worn out surfaces of the test specimens were scrutinized.
Abstract: Evaluation of crop plants resistance to environmental
stresses specially in germination stage is a critical factor in their
selection in different conditions of cultivation. Therefore use of a
procedure in controllable situation can help to evaluate plants
reaction to stress quickly and precisely. In order to study germination
characteristics of flax in water and salinity stress conditions were
conducted two laboratories experimental. The two experimental were
conducted in 4-replicant completing random design for salinity and
water stress. The treatment, for salinity and water stress was three
potential (zero, 40, 80 mM) of NaCl and three potential (zero, -2, -4
bar) of PEG respectively. Germination percentage and rate, in
addition to Radical and plumule length and dry-weight and
plumule/Radical ration were measured. All of characteristics reduce
under water stress conditions. salinity stress significant reduce
germination rate and Radical and plumule length of flax seeds.
Hydropriming and osmopriming significant increased germination
rate, plumule length and plumule/Radical ration ration of flax seeds.
But germination percentage and Radical and plumule dry weight
significant increased only in hydropriming treat. Hydropriming and
osmopriming could not be used to improved germination under saline
and drought stress. But has more tolerance in salinity and drought
stress in flax by less reduce in Radical and plumule length under
saline and drought stress.
Abstract: A three-dimensional finite element modeling for austenitic stainless steel AISI 304 annealed condition sheets of 1.0 mm thickness are developed using ABAQUS® software. This includes spot welded and weld bonded joints models. Both models undergo thermal heat caused by spot welding process and then are subjected to axial load up to the failure point. The properties of elastic and plastic regions, modulus of elasticity, fracture limit, nugget and heat affected zones are determined. Complete loaddisplacement curve for each joining model is obtained and compared with the experiment data and with the finite element models without including the effect of thermal process. In general, the results obtained for both spot welded and weld-bonded joints affected by thermal process showed an excellent agreement with the experimental data.
Abstract: Face recognition in the infrared spectrum has attracted a lot of interest in recent years. Many of the techniques used in infrared are based on their visible counterpart, especially linear techniques like PCA and LDA. In this work, we introduce a probabilistic Bayesian framework for face recognition in the infrared spectrum. In the infrared spectrum, variations can occur between face images of the same individual due to pose, metabolic, time changes, etc. Bayesian approaches permit to reduce intrapersonal variation, thus making them very interesting for infrared face recognition. This framework is compared with classical linear techniques. Non linear techniques we developed recently for infrared face recognition are also presented and compared to the Bayesian face recognition framework. A new approach for infrared face extraction based on SVM is introduced. Experimental results show that the Bayesian technique is promising and lead to interesting results in the infrared spectrum when a sufficient number of face images is used in an intrapersonal learning process.