Abstract: The objective of present work is to stimulate the
machining of material by electrical discharge machining (EDM) to
give effect of input parameters like discharge current (Ip), pulse on
time (Ton), pulse off time (Toff) which can bring about changes in the
output parameter, i.e. material removal rate. Experimental data was
gathered from die sinking EDM process using copper electrode and
Medium Carbon Steel (AISI 1040) as work-piece. The rules of
membership function (MF) and the degree of closeness to the
optimum value of the MMR are within the upper and lower range of
the process parameters. It was found that proposed fuzzy model is in
close agreement with the experimental results. By Intelligent, model
based design and control of EDM process parameters in this study
will help to enable dramatically decreased product and process
development cycle times.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.
Abstract: The objective of this study is to investigate fire
behaviors, experimentally and numerically, in a scaled version of an
underground station. The effect of ventilation velocity on the fire is
examined. Fire experiments are simulated by burning 10 ml
isopropyl alcohol fuel in a fire pool with dimensions 5cm x 10cm x 4
mm at the center of 1/100 scaled underground station model. A
commercial CFD program FLUENT was used in numerical
simulations. For air flow simulations, k-ω SST turbulence model and
for combustion simulation, non-premixed combustion model are
used. This study showed that, the ventilation velocity is increased
from 1 m/s to 3 m/s the maximum temperature in the station is found
to be less for ventilation velocity of 1 m/s. The reason for these
experimental result lies on the relative dominance of oxygen supply
effect on cooling effect. Without piston effect, maximum temperature
occurs above the fuel pool. However, when the ventilation velocity
increased the flame was tilted in the direction of ventilation and the
location of maximum temperature moves along the flow direction.
The velocities measured experimentally in the station at different
locations are well matched by the CFD simulation results. The
prediction of general flow pattern is satisfactory with the smoke
visualization tests. The backlayering in velocity is well predicted by
CFD simulation. However, all over the station, the CFD simulations
predicted higher temperatures compared to experimental
measurements.
Abstract: Low temperature (LT) is one of the most abiotic
stresses causing loss of yield in wheat (T. aestivum). Four major
genes in wheat (Triticum aestivum L.) with the dominant alleles
designated Vrn–A1,Vrn–B1,Vrn–D1 and Vrn4, are known to have
large effects on the vernalization response, but the effects on cold
hardiness are ambiguous. Poor cold tolerance has restricted winter
wheat production in regions of high winter stress [9]. It was known
that nearly all wheat chromosomes [5] or at least 10 chromosomes of
21 chromosome pairs are important in winter hardiness [15]. The
objective of present study was to clarify the role of each chromosome
in cold tolerance. With this purpose we used 20 isogenic lines of
wheat. In each one of these isogenic lines only a chromosome from
‘Bezostaya’ variety (a winter habit cultivar) was substituted to
‘Capple desprez’ variety. The plant materials were planted in
controlled conditions with 20º C and 16 h day length in moderately
cold areas of Iran at Karaj Agricultural Research Station in 2006-07
and the acclimation period was completed for about 4 weeks in a
cold room with 4º C. The cold hardiness of these isogenic lines was
measured by LT50 (the temperature in which 50% of the plants are
killed by freezing stress).The experimental design was completely
randomized block design (RCBD)with three replicates. The results
showed that chromosome 5A had a major effect on freezing
tolerance, and then chromosomes 1A and 4A had less effect on this
trait. Further studies are essential to understanding the importance of
each chromosome in controlling cold hardiness in wheat.
Abstract: Recent quasi-experimental evaluation of the Canadian Active Labour Market Policies (ALMP) by Human Resources and Skills Development Canada (HRSDC) has provided an opportunity to examine alternative methods to estimating the incremental effects of Employment Benefits and Support Measures (EBSMs) on program participants. The focus of this paper is to assess the efficiency and robustness of inverse probability weighting (IPW) relative to kernel matching (KM) in the estimation of program effects. To accomplish this objective, the authors compare pairs of 1,080 estimates, along with their associated standard errors, to assess which type of estimate is generally more efficient and robust. In the interest of practicality, the authorsalso document the computationaltime it took to produce the IPW and KM estimates, respectively.
Abstract: This paper presents comparative emission study of
newly introduced gasoline/LPG bifuel automotive engine in Indian
market. Emissions were tested as per LPG-Bharat stage III driving
cycle. Emission tests were carried out for urban cycle and extra urban
cycle. Total time for urban and extra urban cycle was 1180 sec.
Engine was run in LPG mode by using conversion system. Emissions
were tested as per standard procedure and were compared. Corrected
emissions were computed by deducting ambient reading from sample
reading. Paper describes detail emission test procedure and results
obtained. CO emissions were in the range of38.9 to 111.3 ppm. HC
emissions were in the range of 18.2 to 62.6 ppm. Nox emissions were
08 to 3.9 ppm and CO2 emissions were from 6719.2 to 8051 ppm.
Paper throws light on emission results of LPG vehicles recently
introduced in Indian automobile market. Objectives of this
experimental study were to measure emissions of engines in gasoline
& LPG mode and compare them.
Abstract: This paper argues that a product development exercise
involves in addition to the conventional stages, several decisions
regarding other aspects. These aspects should be addressed
simultaneously in order to develop a product that responds to the
customer needs and that helps realize objectives of the stakeholders
in terms of profitability, market share and the like. We present a
framework that encompasses these different development
dimensions. The framework shows that a product development
methodology such as the Quality Function Deployment (QFD) is the
basic tool which allows definition of the target specifications of a
new product. Creativity is the first dimension that enables the
development exercise to live and end successfully. A number of
group processes need to be followed by the development team in
order to ensure enough creativity and innovation. Secondly,
packaging is considered to be an important extension of the product.
Branding strategies, quality and standardization requirements,
identification technologies, design technologies, production
technologies and costing and pricing are also integral parts to the
development exercise. These dimensions constitute the proposed
framework. The paper also presents a mathematical model used to
calculate the design targets based on the target costing principle. The
framework is used to study a case of a new product development in
the telecommunications services sector.
Abstract: The objective of this research is to investigate the
advantages of using large-diameter 0.7 inch prestressing strands in
pretention applications. The advantages of large-diameter strands are
mainly beneficial in the heavy construction applications. Bridges and
tunnels are subjected to a higher daily traffic with an exponential
increase in trucks ultimate weight, which raise the demand for higher
structural capacity of bridges and tunnels. In this research, precast
prestressed I-girders were considered as a case study. Flexure
capacities of girders fabricated using 0.7 inch strands and different
concrete strengths were calculated and compared to capacities of 0.6
inch strands girders fabricated using equivalent concrete strength.
The effect of bridge deck concrete strength on composite deck-girder
section capacity was investigated due to its possible effect on final
section capacity. Finally, a comparison was made to compare the
bridge cross-section of girders designed using regular 0.6 inch strands
and the large-diameter 0.7 inch. The research findings showed that
structural advantages of 0.7 inch strands allow for using fewer bridge
girders, reduced material quantity, and light-weight members. The
structural advantages of 0.7 inch strands are maximized when high
strength concrete (HSC) are used in girder fabrication, and concrete
of minimum 5ksi compressive strength is used in pouring bridge
decks. The use of 0.7 inch strands in bridge industry can partially
contribute to the improvement of bridge conditions, minimize
construction cost, and reduce the construction duration of the project.
Abstract: In this presentation, we discuss the use of information technologies in the area of special education for teaching individuals with learning disabilities. Application software which was developed for this purpose is used to demonstrate the applicability of a database integrated information processing system to alleviate the burden of educators. The software allows the preparation of individualized education programs based on the predefined objectives, goals and behaviors.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.
Abstract: The main objective of this research was to investigate
the biosorption capacity for biofilms of sulphate reducing bacteria
(SRB) to remove heavy metals, such as Zn, Pb and Cd from
rainwater using laboratory-scale reactors containing mixed support
media. Evidence showed that biosorption had contributed to removal
of heavy metals including Zn, Pb and Cd in presence of SRB and
SRB were also found in the aqueous samples from reactors.
However, the SRB and specific families (Desulfobacteriaceae and
Desulfovibrionaceae) were found mainly in the biomass samples
taken from all reactors at the end of the experiment. EDX-analysis
of reactor solids at end of experiment showed that heavy metals Zn,
Pb and Cd had also accumulated in these precipitates.
Abstract: Knowledge of factors, which influence stress and its
distribution, is of key importance to the successful production of
durable restorations. One of this is the marginal geometry. The
objective of this study was to evaluate, by finite element analysis
(FEA), the influence of different marginal designs on the stress
distribution in teeth prepared for cast metal crowns. Five margin
designs were taken into consideration: shoulderless, chamfer,
shoulder, sloped shoulder and shoulder with bevel. For each kind of
preparation three dimensional finite element analyses were initiated.
Maximal equivalent stresses were calculated and stress patterns were
represented in order to compare the marginal designs. Within the
limitation of this study, the shoulder and beveled shoulder margin
preparations of the teeth are preferred for cast metal crowns from
biomechanical point of view.
Abstract: In this paper, all variables are supposed to be integer
and positive. In this modern method, objective function is assumed to
be maximized or minimized but constraints are always explained like
less or equal to. In this method, choosing a dual combination of ideal
nonequivalent and omitting one of variables. With continuing this
act, finally, having one nonequivalent with (n-m+1) unknown
quantities in which final nonequivalent, m is counter for constraints,
n is counter for variables of decision.
Abstract: This paper deals with under actuator dynamic systems such as spring-mass-damper system when the number of control variable is less than the number of state variable. In order to apply optimal control, the controllability must be checked. There are many objective functions to be selected as the goal of the optimal control such as minimum energy, maximum energy and minimum jerk. As the objective function is the first priority, if one like to have the second goal to be applied; however, it could not fit in the objective function format and also avoiding the vector cost for the objective, this paper will illustrate the problem of under actuator dynamic systems with the easiest to deal with comparing between minimum energy and minimum jerk.
Abstract: The objectives of this research are to search the
management pattern of Bang Khonthi lodging entrepreneurs for
sufficient economy ways, to know the threat that affects this sector
and design fit arrangement model to sustain their business with
Samut Songkram style. What will happen if they do not use this
approach? Will they have a financial crisis? The data and information
are collected by informal discussions with 8 managers and 400
questionnaires. A mixed methods of both qualitative research and
quantitative research are used. Bent Flyvbjerg-s phronesis is utilized
for this analysis. Our research will prove that sufficient economy can
help small business firms to solve their problems. We think that the
results of our research will be a financial model to solve many
problems of the entrepreneurs and this way will can be a model for
other provinces of Thailand.
Abstract: Environmental considerations have become an integral part of developmental thinking and decision making in many countries. It is growing rapidly in importance as a discipline of its own. Preventive approaches have been used at the evolutional process of environmental management as a broad and dynamic system for dealing with pollution and environmental degradation. In this regard, Environmental Assessment as an activity for identification and prediction of project’s impacts carried out in the world and its legal significance dates back to late 1960. In Iran, according to the Article 2 of Environmental Protection Act, Environmental Impact Assessment (EIA) should be prepared for seven categories of project. This article has been actively implementing by Department of Environment at 1997. World Bank in 1989 attempted to introducing application of Environmental Assessment for making decision about projects which are required financial assistance in developing countries. So, preparing EIA for obtaining World Bank loan was obligated. Alborz Project is one of the World Bank Projects in Iran which is environmentally significant. Seven out of ten W.B safeguard policies were considered at this project. In this paper, Alborz project, objectives, safeguard policies and role of environmental management will be elaborated
Abstract: The primary objective of the paper is to propose a new method for solving assignment problem under uncertain situation. In the classical assignment problem (AP), zpqdenotes the cost for assigning the qth job to the pth person which is deterministic in nature. Here in some uncertain situation, we have assigned a cost in the form of composite relative degree Fpq instead of and this replaced cost is in the maximization form. In this paper, it has been solved and validated by the two proposed algorithms, a new mathematical formulation of IVIF assignment problem has been presented where the cost has been considered to be an IVIFN and the membership of elements in the set can be explained by positive and negative evidences. To determine the composite relative degree of similarity of IVIFS the concept of similarity measure and the score function is used for validating the solution which is obtained by Composite relative similarity degree method. Further, hypothetical numeric illusion is conducted to clarify the method’s effectiveness and feasibility developed in the study. Finally, conclusion and suggestion for future work are also proposed.
Abstract: In large Internet backbones, Service Providers
typically have to explicitly manage the traffic flows in order to
optimize the use of network resources. This process is often referred
to as Traffic Engineering (TE). Common objectives of traffic
engineering include balance traffic distribution across the network
and avoiding congestion hot spots. Raj P H and SVK Raja designed
the Bayesian network approach to identify congestion hors pots in
MPLS. In this approach for every node in the network the
Conditional Probability Distribution (CPD) is specified. Based on
the CPD the congestion hot spots are identified. Then the traffic can
be distributed so that no link in the network is either over utilized or
under utilized. Although the Bayesian network approach has been
implemented in operational networks, it has a number of well known
scaling issues.
This paper proposes a new approach, which we call the Pragati
(means Progress) Node Popularity (PNP) approach to identify the
congestion hot spots with the network topology alone. In the new
Pragati Node Popularity approach, IP routing runs natively over the
physical topology rather than depending on the CPD of each node as
in Bayesian network. We first illustrate our approach with a simple
network, then present a formal analysis of the Pragati Node
Popularity approach. Our PNP approach shows that for any given
network of Bayesian approach, it exactly identifies the same result
with minimum efforts. We further extend the result to a more
generic one: for any network topology and even though the network
is loopy. A theoretical insight of our result is that the optimal routing
is always shortest path routing with respect to some considerations of
hot spots in the networks.
Abstract: This paper proposes an investment cost recovery
based efficient and fast sequential optimization approach to optimal
allocation of thyristor controlled series compensator (TCSC) in
competitive power market. The optimization technique has been used
with an objective to maximizing the social welfare and minimizing
the device installation cost by suitable location and rating of TCSC in
the system. The effectiveness of proposed approach for location of
TCSC has been compared with some existing methods of TCSC
placement, in terms of its impact on social welfare, TCSC investment
recovery and optimal generation as well as load patterns. The results
have been obtained on modified IEEE 14-bus system.