Abstract: This paper contributes to the debate on the proximate
causes of climate change. Also, it discusses the impact of the global
temperature increases since the beginning of the twentieth century
and the effectiveness of climate change models in isolating the
primary cause (anthropogenic influences or natural variability in
temperature) of the observed temperature increases that occurred
within this period. The paper argues that if climate scientist and
policymakers ignore the anthropogenic influence (greenhouse gases)
on global warming on the pretense of lack of agreement among
various climate models and their inability to account for all the
necessary factors of global warming at all levels the current efforts of
greenhouse emissions control and global warming as a whole could
be exacerbated.
Abstract: The pollutant removal efficiency of the Intermittently
Decanted Extended Aeration (IDEA) wastewater treatment system at
Curtin University Sarawak Campus, and conventional activated
sludge wastewater treatment system at a local resort, Resort A, is
monitored. The influent and effluent characteristics are tested during
wet and dry weather conditions, and peak and off peak periods. For
the wastewater treatment systems at Curtin Sarawak and Resort A,
during dry weather and peak season, it was found that the BOD5
concentration in the influent is 121.7mg/L and 80.0mg/L
respectively, and in the effluent, 18.7mg/L and and 18.0mg/L
respectively. Analysis of the performance of the IDEA treatment
system showed that the operational costs can be minimized by 3%, by
decreasing the number of operating cycles. As for the treatment
system in Resort A, by utilizing a smaller capacity air blower, a
saving of 12% could be made in the operational costs.
Abstract: Environmental studies have expanded dramatically all
over the world in the past few years. Nowadays businesses interact
with society and the environment in ways that put their mark on both
sides. Efforts improving human standard living, through the control
of nature and the development of new products, have also resulted in
contamination of the environment. Consequently companies play an
important role in environmental sustainability of a region or country.
Therefore we can say that a company's sustainable development is
strictly dependent on the environment. This article presents a fuzzy
model to evaluate a company's environmental impact. Article
illustrates an example of the automotive industry in order to prove the
usefulness of using such a model.
Abstract: The river flow forecasting represents a crucial point to employ for improving a management policy addressed to the right use of water resources as well as for conjugating prevention and defense actions against environmental degradation. The difficulties occurring during the field activities encourage the development and implementation of operative computation and measuring methods addressed to time reduction for data acquisition and processing maintaining a good level of accuracy. Therefore, the aim of the present work is to test a new entropy based expeditive methodology for the evaluation of the rating curves on three gauged sections with different geometric and morphological characteristics. The methodology requires the choice of only three verticals along the measure section and the sampling of only the maximum velocity. The results underline how in most conditions the rating curves drawn can replace those built with classic methodologies, simplifying thus the procedures of data monitoring and calculation.
Abstract: The main aims in this research are to study the solid
waste generation in the Faculty of Engineering and Built
Environment in the UKM and at the same time to determine
composition and some of the waste characteristics likewise: moisture
content, density, pH and C/N ratio. For this purpose multiple
campaigns were conducted to collect the wastes produced in all
hostels, faculties, offices and so on, during 24th of February till 2nd
of March 2009, measure and investigate them with regard to both
physical and chemical characteristics leading to highlight the
necessary management policies. Research locations are Faculty of
Engineering and the Canteen nearby that. From the result gained, the
most suitable solid waste management solution will be proposed to
UKM. The average solid waste generation rate in UKM is 203.38
kg/day. The composition of solid waste generated are glass, plastic,
metal, aluminum, organic and inorganic waste and others waste.
From the laboratory result, the average moisture content, density, pH
and C/N ratio values from the solid waste generated are 49.74%,
165.1 kg/m3, 5.3, and 7:1 respectively. Since, the food waste (organic
waste) were the most dominant component, around 62% from the
total waste generated hence, the most suitable solid waste
management solution is composting.
Abstract: This study investigated the presence of polycyclic
aromatic hydrocarbons (PAHs) in the sediments of the Musa Bay
(around the PETZONE coastal area) from Feb 2010 to Jun 2010.
Concentrations of PAHs recorded in the Musa Bay sediments ranged
from 537.89 to 26,659.06 ng/g dry weight with a mean value of
3990.74 ng/g. the highest concentration of PAHs was observed at
station 4, which is located near the aromatic outlet of Imam
Khomeini petrochemical company (station 4: BI-PC Aromatic
effluent outlet) in which its concentration level was more than the
NOAA sediment quality guideline value (ERL= 4022 ng/g dry
weight). Owing to the concentration of PAHs in the study area, its
concentration level was still meet the NOAA sediment quality
guideline value (ERL: 4022 ng/g dry weight); however, according to
the PELq factor, slightly adverse biological effects are associated
with the exposure to PAHs levels in the study area (0.1< PELq= 0.24
> 0.5).
Abstract: The aim of this study was to examine the dynamics of functional composition of a non flooded Amazonian forest in response to drought stress in terms of diameter growth, recruitment and mortality. The survey was carried out in the continuous forest of the Biological dynamics of forest fragments project 90 km outside the city of Manaus, state of Amazonas Brazil. All stems >10 cm dbh where identified to species level and monitored in 18 one hectare permanent sample plots from 1981 to 2004.For statistical analysis all species where aggregated in three ecological guilds. Two distinct drought events occurred in 1983 and 1997. Results showed that more early successional species performed better than later successional ones. Response was significant for both events but for the 1997 event this was more pronounced possibly because of the fact that the event was in the middle of the dry rather than the wet period as was the 1983 one.
Abstract: Recent research on seeds of bio-diesel plants like
Jatropha curcas, constituting 40-50% bio-crude oil indicates its
potential as one of the most promising alternatives to conventional
sources of energy. Also, limited studies on utilization of de-oiled cake
have revealed that Jatropha bio-waste has good potential to be used as
organic fertilizers produced via aerobic and anaerobic treatment.
However, their commercial exploitation has not yet been possible. The
present study aims at developing appropriate bio-processes and
formulations utilizing Jatropha seed cake as organic fertilizer, for
improving the growth of Polianthes tuberose L. (Tuberose). Pot
experiments were carried out by growing tuberose plants on soil
treated with composted formulations of Jatropha de-oiled cake, Farm
Yard Manure (FYM) and inorganic fertilizers were also blended in
soil. The treatment was carried out through soil amendment as well as
foliar spray. The growth and morphological parameters were
monitored for entire crop cycle.
The growth Length and number of leaves, spike length, rachis
length, number of bulb per plant and earliness of sprouting of bulb and
yield enhancement were comparable to that achieved under inorganic
fertilizer. Furthermore, performance of inorganic fertilizer also showed
an improvement when blended with composted bio-waste. These
findings would open new avenues for Jatropha based bio-wastes to be
composted and used as organic fertilizers for commercial floriculture.
Abstract: Cry j 1 is a causative substance of Japanese cedar
pollinosis, and it may deteriorate by Cry j 1 invasion to a lower
respiratory tract. We observed airborne particles containing Cry j 1 by
an immunofluorescence technique using a fluorescence microscope,
and we clarified that Cry j 1 exist as aggregates of airborne fine
particles (< 1.1 μm) in the urban atmosphere. Airborne Cry j 1 may
react with air pollutants and be denature to a substance deteriorated
Japanese cedar pollinosis. Therefore, we applied a sodium dodecyl
sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) to evaluate a
Cry j 1 reacted with various air pollutants by liquid phase reaction,
and calculated kinetics constants of Cry j 1 extracted from pollens
collected in various sites and airborne fine particles containing Cry j
1 by using a surface plasmon resonance (SPR) method. As a result, it
is suggested that Cry j 1 may be denatured by air pollutants during
the transportation to the urban atmosphere.
Abstract: The interaction of tunneling or mining with
groundwater has become a very relevant problem not only due to the
need to guarantee the safety of workers and to assure the efficiency of
the tunnel drainage systems, but also to safeguard water resources
from impoverishment and pollution risk. Therefore it is very
important to forecast the drainage processes (i.e., the evaluation of
drained discharge and drawdown caused by the excavation). The aim
of this study was to know better the system and to quantify the flow
drained from the Fontane mines, located in Val Germanasca (Turin,
Italy). This allowed to understand the hydrogeological local changes
in time. The work has therefore been structured as follows: the
reconstruction of the conceptual model with the geological,
hydrogeological and geological-structural study; the calculation of
the tunnel inflows (through the use of structural methods) and the
comparison with the measured flow rates; the water balance at the
basin scale. In this way it was possible to understand what are the
relationships between rainfall, groundwater level variations and the
effect of the presence of tunnels as a means of draining water.
Subsequently, it the effects produced by the excavation of the mining
tunnels was quantified, through numerical modeling. In particular,
the modeling made it possible to observe the drawdown variation as a
function of number, excavation depth and different mines linings.
Abstract: Since the beginning of human history, human
activities have caused many changes in the environment. Today, a
particular attention should be paid to gaining knowledge about water
quality of wetlands which are pristine natural environments rich in
genetic reserves. If qualitative conditions of industrial areas (in terms
of both physicochemical and biological conditions) are not addressed
properly, they could cause disruption in natural ecosystems,
especially in rivers. With regards to the quality of water resources,
determination of pollutant sources plays a pivotal role in engineering
projects as well as designing water quality control systems. Thus,
using different methods such as flow duration curves, dischargepollution
load model and frequency analysis by HYFA software
package, risk of various industrial pollutants in international and
ecologically important Gavkhoni wetland is analyzed. In this study, a
station located at Varzaneh City is used as the last station on
Zayanderud River, from where the river water is discharged into the
wetland. Results showed that elements- concentrations often
exceeded the allowed level and river water can endanger regional
ecosystem. In addition, if the river discharge is managed on Q25
basis, this basis can lower concentrations of elements, keeping them
within the normal level.
Abstract: This research aimed to study on the potential of
recycling organic waste in Suan Sunandha Rajabhat University as
compost. In doing so, the composition of solid waste generated in the
campus was investigated while physical and chemical properties of
organic waste were analyzed in order to evaluate the portion of waste
suitable for recycling as compost. As a result of the study, it was
found that (1) the amount of organic waste was averaged at 299.8
kg/day in which mixed food wastes had the highest amount of 191.9
kg/day followed by mixed leave & yard wastes and mixed fruit &
vegetable wastes at the amount of 66.3 and 41.6 kg/day respectively;
(2) physical and chemical properties of organic waste in terms of
moisture content was between 69.54 to 78.15%, major elements for
plant as N, P and K were 0.14 to 0.17%, 0.46 to 0.52% and 0.16 to
0.18% respectively, and carbon/nitrogen ratio (C/N) was about 15:1
to 17.5:1; (3) recycling organic waste as compost was designed by
aerobic decomposition using mixed food wastes : mixed leave & yard
wastes : mixed fruit & vegetable wastes at the portion of 3:2:1 by
weight in accordance with the potential of their amounts and their
physical and chemical properties.
Abstract: This study investigates the in-situ regeneration of deactivated Pt-Pd catalyst in a laboratory-scale catalysis reactor. Different regeneration conditions are tested and the activity and characteristics of regenerated catalysts are analyzed. Experimental results show that the conversion efficiencies of C3H6 by different regenerated Pt-Pd catalysts were significantly improved from 77%, 55% and 41% to 86%, 98% and 99%, respectively. The best regeneration conditions was 52ppm ozone, 500oC, and 10min. Regeneration temperature has more influences than ozone concentration and regeneration time. With the comparisons of characteristics of deactivated catalyst and regenerated catalyst, the major poison species (carbon, metals, chloride, and sulfate) on the spent catalysts can be effectively removed by ozone regeneration.
Abstract: The charnockitic and associated granitic rocks of Akure area were studied for their field and petrographic relationship's. The outcrops locations were plotted in Surfer 8. The granitic rock exhibits a porphyritic texture and outcrops in the north-eastern side of the study area while the charnockitics outcrop in the central/western part. An essentially dark coloured and fine grained intrusive exhibiting xenoliths and xenocrysts (plagioclase phenocrysts) of the granite outcrops between the granitic and charnockitic rocks. Mineralogically, the central rock combines the content of the other two indicating that it is most likely a product of their hybridization. The charnockitic magma is believed to have intruded and assimilated the granite substantially thereby contaminating itself and consequently emplacing the hybrid. The presented model of emplacement elucidates the hybridization proposal. Conclusively, the charnockitics are believed to be (a) younger than the granite, (b) of Pan-African age and (c) of igneous origin.
Abstract: According to the European laws, there is the
possibility of reusing the washing wastes for the environmental
requalification of quarry lakes. The paper deals with the
hydrogeological aspects involved in this possibility, as the
introduction of finest wastes in the quarry lakes can generate
alterations of the hydrogeological setting of the area, and problems
for the future accessibility of the zone. To evaluate the
hydrogeological compatibility of the washing wastes reuse in quarry
lakes a groundwater numerical model was carried out, pointing out
both the hydrogeological feasibility of this intervention and some
guide lines for its optimization, in terms of inflow point with regard
the groundwater flow direction and loss of volume in the quarry lake.
Abstract: Since atmosphere pressure field is an actual envoy of
climatic signal the atmospheric Highs and Lows should be attributed
to the key active focal points within the ocean-atmosphere interplay
system. Here we were set a task to determine how the dynamics of
those centres of action relates to the climate change both on regional
and global scales. For this target the near-surface temperature and
atmospheric pressure differences between the Icelandic Low and the
Azores High were considered. The secular term of phase states of the
system under consideration was found divided into three
nonintersecting subsets. Each of that was put in consequence with
one of three climatic scenarios related to the periods of 1905-1935
(relatively warm phase), 1940-1970 (cold phase) and 1980-2000
(warm phase).
Abstract: This paper focuses on assessment of air pollution in Umm-Alhyman, Kuwait, which is located south to oil refineries, power station, oil field, and highways. The measurements were made over a period of four days in March and July in 2001, 2004, and 2008. The measured pollutants included methanated and nonmethanated hydrocarbons (MHC, NMHC), CO, CO2, SO2, NOX, O3, and PM10. Also, meteorological parameters were measured, which includes temperature, wind speed and direction, and solar radiation. Over the study period, data analysis showed increase in measured SO2, NOX and CO by factors of 1.2, 5.5 and 2, respectively. This is explained in terms of increase in industrial activities, motor vehicle density, and power generation. Predictions of the measured data were made by the ISC-AERMOD software package and by using the ISCST3 model option. Finally, comparison was made between measured data against international standards.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: Paper is dealing with vulnerability concerning elements of hydrological structures and elements of technological equipments which are acceptable for groundwater resources. The vulnerability assessment stems from the application of the register of hazards and a potential threat to individual water source elements within each type of hazard. The proposed procedure is pattern for assessing the risks of disturbance, damage, or destruction of water source by the identified natural or technological hazards and consequently for classification of these risks in relation to emergency water supply. Using of this procedure was verified on selected groundwater resource in particular region, which seems to be as potentially useful for crisis planning system.
Abstract: The compressive strength development through
polymerization process of alkaline solution and fly ash blended with Microwave Incinerated Rice Husk Ash (MIRHA) is described in this
paper. Three curing conditions, which are hot gunny curing, ambient
curing, and external humidity curing are investigated to obtain the suitable curing condition for cast in situ provision. Fly ash was
blended with MIRHA at 3%, 5%, and 7% to identify the effect of blended mixes to the compressive strength and microstructure
properties of geopolymer concrete. Compressive strength results
indicated an improvement in the strength development with external humidity curing concrete samples compared to hot gunny curing and
ambient curing. Blended mixes also presented better performance
than control mixes. Improvement of interfacial transition zone (ITZ)
and micro structure in external humidity concrete samples were also
identified compared to hot gunny and ambient curing.