Abstract: The transient hydrodynamics and thermal behaviors of
fluid flow in open-ended vertical parallel-plate porous microchannel are investigated semi-analytically under the effect of the hyperbolic
heat conduction model. The model that combines both the continuum approach and the possibility of slip at the boundary is adopted in the
study. The Effects of Knudsen number , Darcy number , and thermal relaxation time on the microchannel hydrodynamics and thermal behaviors are investigated using the hyperbolic heat
conduction models. It is found that as increases the slip in the hydrodynamic and thermal boundary condition increases. This slip in
the hydrodynamic boundary condition increases as increases. Also, the slip in the thermal boundary condition increases as
decreases especially the early stage of time.
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. Transient mode super position method has been used to
find horizontal and vertical components of displacement and
dynamic stress. The finite element analysis software ANSYS has
been used on the proposed model to find the natural frequencies by
Block Lanczos technique and displacements and dynamic stresses by
transient mode super position method. A comparison of theoretical
(natural frequency and static stress) results with the finite element
analysis results has also been done. The effect of rotational speed of
the gears on the dynamic response of gear tooth has been studied and
design limits have been discussed.
Abstract: In this paper, we use nonlinear system identification method to predict and detect process fault of a cement rotary kiln. After selecting proper inputs and output, an input-output model is identified for the plant. To identify the various operation points in the
kiln, Locally Linear Neuro-Fuzzy (LLNF) model is used. This model is trained by LOLIMOT algorithm which is an incremental treestructure
algorithm. Then, by using this method, we obtained 3
distinct models for the normal and faulty situations in the kiln. One of the models is for normal condition of the kiln with 15 minutes
prediction horizon. The other two models are for the two faulty situations in the kiln with 7 minutes prediction horizon are presented.
At the end, we detect these faults in validation data. The data collected from White Saveh Cement Company is used for in this study.
Abstract: In this paper, we propose an architecture for easily
constructing a robot controller. The architecture is a multi-agent
system which has eight agents: the Man-machine interface, Task
planner, Task teaching editor, Motion planner, Arm controller,
Vehicle controller, Vision system and CG display. The controller has
three databases: the Task knowledge database, the Robot database and
the Environment database. Based on this controller architecture, we
are constructing an experimental power distribution line maintenance
robot system and are doing the experiment for the maintenance tasks,
for example, “Bolt insertion task".
Abstract: The Non-Rotating Adjustable Stabilizer / Directional
Solution (NAS/DS) is the imitation of a mechanical process or an
object by a directional drilling operation that causes a respond
mathematically and graphically to data and decision to choose the
best conditions compared to the previous mode.
The NAS/DS Auto Guide rotary steerable tool is undergoing final
field trials. The point-the-bit tool can use any bit, work at any
rotating speed, work with any MWD/LWD system, and there is no
pressure drop through the tool. It is a fully closed-loop system that
automatically maintains a specified curvature rate.
The Non–Rotating Adjustable stabilizer (NAS) can be controls
curvature rate by exactly positioning and run with the optimum bit,
use the most effective weight (WOB) and rotary speed (RPM) and
apply all of the available hydraulic energy to the bit. The directional
simulator allowed to specify the size of the curvature rate
performance errors of the NAS tool and the magnitude of the random
errors in the survey measurements called the Directional Solution
(DS).
The combination of these technologies (NAS/DS) will provide
smoother bore holes, reduced drilling time, reduced drilling cost and
incredible targeting precision. This simulator controls curvature rate
by precisely adjusting the radial extension of stabilizer blades on a
near bit Non-Rotating Stabilizer and control process corrects for the
secondary effects caused by formation characteristics, bit and tool
wear, and manufacturing tolerances.
Abstract: In this paper a new control strategy based on Brain
Emotional Learning (BEL) model has been introduced. A modified
BEL model has been proposed to increase the degree of freedom,
controlling capability, reliability and robustness, which can be
implemented in real engineering systems.
The performance of the proposed BEL controller has been
illustrated by applying it on different nonlinear uncertain systems,
showing very good adaptability and robustness, while maintaining
stability.
Abstract: Any rotation of a 3-dimensional object can be performed by three consecutive rotations over Euler angles. Intrinsic rotations produce the same result as extrinsic rotations in transformation. Euler rotations are the movement obtained by changing one of the Euler angles while leaving the other two constant. These Euler rotations are applied in a simple two-axis gimbals set mounted on an automotives. The values of Euler angles are [π/4, π/4, π/4] radians inside the angles ranges for a given coordinate system and these actual orientations can be directly measured from these gimbals set of moving automotives but it can occur the gimbals lock in application at [π/2.24, 0, 0] radians. In order to avoid gimbals lock, the values of quaternion must be [π/4.8, π/8.2, 0, π/4.8] radians. The four-gimbals set can eliminate gimbals lock.
Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: The present work compares the performance of three
turbulence modeling approach (based on the two-equation k -ε
model) in predicting erosive wear in multi-size dense slurry flow
through rotating channel. All three turbulence models include
rotation modification to the production term in the turbulent kineticenergy
equation. The two-phase flow field obtained numerically
using Galerkin finite element methodology relates the local flow
velocity and concentration to the wear rate via a suitable wear model.
The wear models for both sliding wear and impact wear mechanisms
account for the particle size dependence. Results of predicted wear
rates using the three turbulence models are compared for a large
number of cases spanning such operating parameters as rotation rate,
solids concentration, flow rate, particle size distribution and so forth.
The root-mean-square error between FE-generated data and the
correlation between maximum wear rate and the operating
parameters is found less than 2.5% for all the three models.
Abstract: The study of human hand morphology reveals that developing an artificial hand with the capabilities of human hand is an extremely challenging task. This paper presents the development of a robotic prosthetic hand focusing on the improvement of a tendon driven mechanism towards a biomimetic prosthetic hand. The design of this prosthesis hand is geared towards achieving high level of dexterity and anthropomorphism by means of a new hybrid mechanism that integrates a miniature motor driven actuation mechanism, a Shape Memory Alloy actuated mechanism and a passive mechanical linkage. The synergy of these actuators enables the flexion-extension movement at each of the finger joints within a limited size, shape and weight constraints. Tactile sensors are integrated on the finger tips and the finger phalanges area. This prosthesis hand is developed with an exact size ratio that mimics a biological hand. Its behavior resembles the human counterpart in terms of working envelope, speed and torque, and thus resembles both the key physical features and the grasping functionality of an adult hand.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: The stability of Newtonian and Non-Newtonian extending films under local or global heating or cooling conditions are considered. The thickness-averaged mass, momentum and energy equations with convective and radiative heat transfer are derived, both for Newtonian and non-Newtonian fluids (Maxwell, PTT and Giesekus models considered). The stability of the system is explored using either eigenvalue analysis or transient simulations. The results showed that the influence of heating and cooling on stability strongly depends on the magnitude of the Peclet number. Examples of stabilization or destabilization of heating or cooling are shown for Pe
Abstract: Since straightness error of linear motor stage is hardly
dependent upon machining accuracy and assembling accuracy, there is
limit on maximum realizable accuracy. To cope with this limitation,
this paper proposed a servo system to compensate straightness error of
a linear motor stage. The servo system is mounted on the slider of the
linear motor stage and moves in the direction of the straightness error
so as to compensate the error. From position dependency and
repeatability of the straightness error of the slider, a feedforward
compensation control is applied to the platform servo control. In the
consideration of required fine positioning accuracy, a platform driven
by an electro-magnetic actuator is suggested and a sliding mode
control was applied. The effectiveness of the sliding mode control was
verified along with some experimental results.
Abstract: Water contains oxygen which may make a human
breathe under water like a fish. Centrifugal separator can separate
dissolved gases from water. Carrier solution can increase the
separation of dissolved oxygen from water. But, to develop an
breathing device for a human under water, the enhancement of
separation of dissolved gases including oxygen and portable devices
which have dc battery based device and proper size are needed.
In this study, we set up experimental device for analyzing
separation characteristics of dissolved gases including oxygen from
water using a battery based portable vacuum pump. We characterized
vacuum state, flow rate of separation of dissolved gases and oxygen
concentration which were influenced by the manufactured vacuum
pump.
Abstract: This paper describes a new supervised fusion (hybrid)
electrocardiogram (ECG) classification solution consisting of a new
QRS complex geometrical feature extraction as well as a new version
of the learning vector quantization (LVQ) classification algorithm
aimed for overcoming the stability-plasticity dilemma. Toward this
objective, after detection and delineation of the major events of ECG
signal via an appropriate algorithm, each QRS region and also its
corresponding discrete wavelet transform (DWT) are supposed as
virtual images and each of them is divided into eight polar sectors.
Then, the curve length of each excerpted segment is calculated
and is used as the element of the feature space. To increase the
robustness of the proposed classification algorithm versus noise,
artifacts and arrhythmic outliers, a fusion structure consisting of
five different classifiers namely as Support Vector Machine (SVM),
Modified Learning Vector Quantization (MLVQ) and three Multi
Layer Perceptron-Back Propagation (MLP–BP) neural networks with
different topologies were designed and implemented. The new proposed
algorithm was applied to all 48 MIT–BIH Arrhythmia Database
records (within–record analysis) and the discrimination power of the
classifier in isolation of different beat types of each record was
assessed and as the result, the average accuracy value Acc=98.51%
was obtained. Also, the proposed method was applied to 6 number
of arrhythmias (Normal, LBBB, RBBB, PVC, APB, PB) belonging
to 20 different records of the aforementioned database (between–
record analysis) and the average value of Acc=95.6% was achieved.
To evaluate performance quality of the new proposed hybrid learning
machine, the obtained results were compared with similar peer–
reviewed studies in this area.
Abstract: An unstructured finite volume numerical model is
presented here for simulating shallow-water flows with wetting and
drying fronts. The model is based on the Green-s theorem in
combination with Chorin-s projection method. A 2nd-order upwind
scheme coupled with a Least Square technique is used to handle
convection terms. An Wetting and drying treatment is used in the
present model to ensures the total mass conservation. To test it-s
capacity and reliability, the present model is used to solve the
Parabolic Bowl problem. We compare our numerical solutions with
the corresponding analytical and existing standard numerical results.
Excellent agreements are found in all the cases.
Abstract: Stainless steel has been employed in many
engineering applications ranging from pharmaceutical equipment to
piping in the nuclear reactors and storage to chemical products. In
this attempt, simulation of fatigue crack growth based on
experimental results of austenitic stainless steel 304L was presented
using AFGROW code when NASGRO mode laws adopted. Double
through crack at hole specimen is used in this investigation under
constant amplitude loading. Effect of mean stress is highlighted.
Results show that fatigue crack growth rate (FCGR) and fatigue life
were affected by maximum applied load and dimension of hole. An
equivalent of Paris law for this material was estimated.
Abstract: The present study is concerned with the effect of
exciting boundary layer on cooling process in a gas-turbine blades.
The cooling process is numerically investigated. Observations show
cooling the first row of moving or stable blades leads to increase
their life-time. Results show that minimum temperature in cooling
line with exciting boundary layer is lower than without exciting.
Using block in cooling line of turbines' blade causes flow pattern and
stability in boundary layer changed that causes increase in heat
transfer coefficient. Results show at the location of block,
temperature of turbines' blade is significantly decreased. The k-ε
turbulence model is used.