Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: Tread design has evolved over the years to achieve the common tread pattern used in current vehicles. However, to meet safety and comfort requirements, tread design considers more than one design factor. Tread design must consider the grip and drainage, and the manner in which to reduce rolling noise, which is one of the main factors considered by manufacturers. The main objective of this study was the application the computational fluid dynamics (CFD) technique to simulate the contact surface of the tire and ground. The results demonstrated an air-Pumping and large pressure drop effect in the process of contact surface. The results also revealed that the pressure can be used to analyze sound pressure level (SPL).
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: Design and land use are closely linked to the
energy efficiency levels for an urban area. The current city
planning practice does not involve an effective land useenergy
evaluation in its 'blueprint' urban plans. The study
proposed an appraisal method that can be embedded in GIS
programs using five planning criteria as how far a planner can
give away from the planning principles (criteria) for the most
energy output s/he can obtain. The case of Balcova, a district
in the Izmir Metropolitan area, is used conformingly for
evaluating the proposed master plan and the geothermal
energy (heating only) use for the concern district.
If the land use design were proposed accordingly at-most
energy efficiency (a 30% obtained), mainly increasing the
density around the geothermal wells and also proposing more
mixed use zones, we could have 17% distortion (infidelity to
the main planning principles) from the original plan. The
proposed method can be an effective tool for planners as
simulation media, of which calculations can be made by GIS
ready tools, to evaluate efficiency levels for different plan
proposals, letting to know how much energy saving causes
how much deviation from the other planning ideals. Lower
energy uses can be possible for different land use proposals
for various policy trials.
Abstract: Recently, lots of researchers are attracted to retrieving
multimedia database by using some impression words and their values.
Ikezoe-s research is one of the representatives and uses eight pairs of
opposite impression words. We had modified its retrieval interface and
proposed '2D-RIB'. In '2D-RIB', after a retrieval person selects a
single basic music, the system visually shows some other music
around the basic one along relative position. He/she can select one of
them fitting to his/her intention, as a retrieval result. The purpose of
this paper is to improve his/her satisfaction level to the retrieval result
in 2D-RIB. One of our extensions is to define and introduce the
following two measures: 'melody goodness' and 'general acceptance'.
We implement them in different five combinations. According to an
evaluation experiment, both of these two measures can contribute to
the improvement. Another extension is three types of customization.
We have implemented them and clarified which customization is
effective.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: Retrieval image by shape similarity, given a template
shape is particularly challenging, owning to the difficulty to derive a
similarity measurement that closely conforms to the common
perception of similarity by humans. In this paper, a new method for the
representation and comparison of shapes is present which is based on
the shape matrix and snake model. It is scaling, rotation, translation
invariant. And it can retrieve the shape images with some missing or
occluded parts. In the method, the deformation spent by the template
to match the shape images and the matching degree is used to evaluate
the similarity between them.
Abstract: Studies were carried out to determine the in vitro
susceptibility of the typhoid pathogens to combined action of Euphorbia hirta, Euphorbia heterophylla and Phyllanthus niruri. Clinical isolates of the typhoid bacilli were subjected to susceptibility testing using agar diffusion technique and the minimum inhibitory
concentration (MIC) determined with tube dilution technique. These
isolates, when challenged with doses of the extracts from the three
medicinal plants showed zones of inhibition as wide as 26±0.2mm, 22±0.1mm and 18±0.0mm respectively. The minimum inhibitory concentration (MIC) revealed organisms inhibited at varying
concentrations of extracts: E. hirta (S. typhi 0.250mg/ml, S. paratyphi A 0.125mg/ml, S. paratyphi B 0.185mg/ml and S. paratyphi C 0.225mg/ml), E. heterophylla (S. typhi 0.280mg/ml, S. paratyphi A
0.150mg/ml, S. paratyphi B 0.200mg/ml and S. paratyphi C 0.250mg/ml) and P. niruri (S. typhi 0.150mg/ml, S. paratyphi A 0.100mg/ml, S. paratyphi B 0.115mg/ml and S. paratyphi C 0.125mg/ml). The results of the synergy between the three plants in
the ration of 1:1:1 showed very low MICs for the test pathogens as follows S. typhi 0.025mg/ml, S. paratyphi A 0.080mg/ml, S. paratyphi B 0.015mg/ml and S. paratyphi C 0.10mg/ml with the
diameter zone of inhibition (DZI) ranging from 35±0.2mm,
28±0.4mm, 20±0.1mm and 32±0.3mm respectively. The secondary
metabolites were identified using simple methods and HPLC. Organic components such as anthroquinones, different alkaloids,
tannins, 6-ethoxy-1,2,3,4-tetrahydro-2,2,4-trimethyl and steroids were identified. The prevalence of Salmonellae, a deadly infectious disease, is still very high in parts of Nigeria. The synergistic action of these three plants is very high. It is concluded that pharmaceutical companies should take advantage of these findings to develop new
anti-typhoid drugs from these plants.
Abstract: The performance of schedules released to a shop floor may greatly be affected by unexpected disruptions. Thus, this paper considers the flexible job shop scheduling problem when processing times of some operations are represented by a uniform distribution with given lower and upper bounds. The objective is to find a predictive schedule that can deal with this uncertainty. The paper compares two genetic approaches to obtain predictive schedule. To determine the performance of the predictive schedules obtained by both approaches, an experimental study is conducted on a number of benchmark problems.
Abstract: This paper discusses the landscape design that could
increase energy efficiency in a house. By planting trees in a house
compound, the tree shades prevent direct sunlight from heating up
the building, and it enables cooling off the surrounding air. The
requirement for air-conditioning could be minimized and the air
quality could be improved. During the life time of a tree, the saving
cost from the mentioned benefits could be up to US $ 200 for each
tree. The project intends to visually describe the landscape design in
a house compound that could enhance energy efficiency and
consequently lead to energy saving. The house compound model was
developed in three dimensions by using AutoCAD 2005, the
animation was programmed by using LightWave 3D softwares i.e.
Modeler and Layout to display the tree shadings in the wall. The
visualization was executed on a VRML Pad platform and
implemented on a web environment.
Abstract: Based on Rayleigh beam theory, the sub-impacts of a
free-free beam struck horizontally by a round-nosed rigid mass is
simulated by the finite difference method and the impact-separation
conditions. In order to obtain the sub-impact force, a uniaxial
compression elastic-plastic contact model is employed to analyze the
local deformation field on contact zone. It is found that the horizontal
impact is a complicated process including the elastic plastic
sub-impacts in sequence. There are two sub-zones of sub-impact. In
addition, it found that the elastic energy of the free-free beam is more
suitable for the Poisson collision hypothesis to explain compression
and recovery processes.
Abstract: The main goal of this paper is to study Statistical Process Control (SPC) with Exponentially Weighted Moving Average (EWMA) control chart when observations are serially-correlated. The characteristic of control chart is Average Run Length (ARL) which is the average number of samples taken before an action signal is given. Ideally, an acceptable ARL of in-control process should be enough large, so-called (ARL0). Otherwise it should be small when the process is out-of-control, so-called Average of Delay Time (ARL1) or a mean of true alarm. We find explicit formulas of ARL for EWMA control chart for Seasonal Autoregressive and Moving Average processes (SARMA) with Exponential white noise. The results of ARL obtained from explicit formula and Integral equation are in good agreement. In particular, this formulas for evaluating (ARL0) and (ARL1) be able to get a set of optimal parameters which depend on smoothing parameter (λ) and width of control limit (H) for designing EWMA chart with minimum of (ARL1).
Abstract: In this research paper we have presented control
architecture for robotic arm movement and trajectory planning using
Fuzzy Logic (FL) and Genetic Algorithms (GAs). This architecture is
used to compensate the uncertainties like; movement, friction and
settling time in robotic arm movement. The genetic algorithms and
fuzzy logic is used to meet the objective of optimal control
movement of robotic arm. This proposed technique represents a
general model for redundant structures and may extend to other
structures. Results show optimal angular movement of joints as result
of evolutionary process. This technique has edge over the other
techniques as minimum mathematics complexity used.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: This paper presents a generalized formulation for the
problem of buckling optimization of anisotropic, radially graded,
thin-walled, long cylinders subject to external hydrostatic pressure.
The main structure to be analyzed is built of multi-angle fibrous
laminated composite lay-ups having different volume fractions of the
constituent materials within the individual plies. This yield to a
piecewise grading of the material in the radial direction; that is the
physical and mechanical properties of the composite material are
allowed to vary radially. The objective function is measured by
maximizing the critical buckling pressure while preserving the total
structural mass at a constant value equals to that of a baseline
reference design. In the selection of the significant optimization
variables, the fiber volume fractions adjoin the standard design
variables including fiber orientation angles and ply thicknesses. The
mathematical formulation employs the classical lamination theory,
where an analytical solution that accounts for the effective axial and
flexural stiffness separately as well as the inclusion of the coupling
stiffness terms is presented. The proposed model deals with
dimensionless quantities in order to be valid for thin shells having
arbitrary thickness-to-radius ratios. The critical buckling pressure
level curves augmented with the mass equality constraint are given
for several types of cylinders showing the functional dependence of
the constrained objective function on the selected design variables. It
was shown that material grading can have significant contribution to
the whole optimization process in achieving the required structural
designs with enhanced stability limits.
Abstract: The present study presents a new approach to automatic
data clustering and classification problems in large and complex
databases and, at the same time, derives specific types of explicit rules
describing each cluster. The method works well in both sparse and
dense multidimensional data spaces. The members of the data space
can be of the same nature or represent different classes. A number
of N-dimensional ellipsoids are used for enclosing the data clouds.
Due to the geometry of an ellipsoid and its free rotation in space
the detection of clusters becomes very efficient. The method is based
on genetic algorithms that are used for the optimization of location,
orientation and geometric characteristics of the hyper-ellipsoids. The
proposed approach can serve as a basis for the development of
general knowledge systems for discovering hidden knowledge and
unexpected patterns and rules in various large databases.
Abstract: ISO 9000 is the most popular and widely adopted meta-standard for quality and operational improvements. However, only limited empirical research has been conducted to examine the impact of ISO 9000 on operational performance based on objective and longitudinal data. To reveal any causal relationship between the adoption of ISO 9000 and operational performance, we examined the timing and magnitude of change in time-based performance as a result of ISO 9000 adoption. We analyzed the changes in operating cycle, inventory days, and account receivable days prior and after the implementation of ISO 9000 in 695 publicly listed manufacturing firms. We found that ISO 9000 certified firms shortened their operating cycle time by 5.28 days one year after the implementation of ISO 9000. In the long-run (3 years after certification), certified firms showed continuous improvement in time-based efficiency, and experienced a shorter operating cycle time of 11 days than that of non-certified firms. There was an average of 6.5% improvement in operating cycle time for ISO 9000 certified firms. Both inventory days and account receivable days showed similar significant improvements after the implementation of ISO 9000, too.
Abstract: Uterine and oviducal fluids are necessary for
capacitation of the spermatozoa and early embryonic development.
The aim of the present study was to determine the effects of estrous
cycle phases (follicular and luteal) on some biological parameters
(enzymes, electrolytes and total proteins) in uterine and oviducal
secretions of ewes. Oviducal and uterine fluids were collected,
diluted and centrifuged. According to our results, concentrations of
GPT, G6PDH, total proteins, K and Na were significantly (P
Abstract: Mathematical models can be used to describe the
transmission of disease. Dengue disease is the most significant
mosquito-borne viral disease of human. It now a leading cause of
childhood deaths and hospitalizations in many countries. Variations
in environmental conditions, especially seasonal climatic parameters,
effect to the transmission of dengue viruses the dengue viruses and
their principal mosquito vector, Aedes aegypti. A transmission model
for dengue disease is discussed in this paper. We assume that the
human and vector populations are constant. We showed that the local
stability is completely determined by the threshold parameter, 0 B . If
0 B is less than one, the disease free equilibrium state is stable. If
0 B is more than one, a unique endemic equilibrium state exists and
is stable. The numerical results are shown for the different values of
the transmission probability from vector to human populations.