Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: Well logging records can help to answer many
questions from a wide range of special interested information and
basic petrophysical properties to formation evaluation of oil and gas
reservoirs. The accurate calculations of porosity in carbonate
reservoirs are the most challenging aspects of the well logging
analysis. Many equations have been developed over the years based
on known physical principles or on empirically derived relationships,
which are used to calculate porosity, estimate lithology, and water
saturation; however these parameters are calculated from well logs by
using modern technique in a current study. Nasiriya oil field is one of
the giant oilfields in the Middle East, and the formation under study
is the Mishrif carbonate formation which is the shallowest
hydrocarbon bearing zone in this oilfield. Neurolog software was
used to digitize the scanned copies of the available logs.
Environmental corrections had been made as per Schlumberger charts
2005, which supplied in the Interactive Petrophysics software. Three
saturation models have been used to calculate water saturation of
carbonate formations, which are simple Archie equation, Dual water
model, and Indonesia model. Results indicate that the Mishrif
formation consists mainly of limestone, some dolomite, and shale.
The porosity interpretation shows that the logging tools have a good
quality after making the environmental corrections. The average
formation water saturation for Mishrif formation is around 0.4-
0.6.This study is provided accurate behavior of petrophysical
properties with depth for this formation by using modern software.
Abstract: This paper addresses the problem of offline path
planning for Unmanned Aerial Vehicles (UAVs) in complex threedimensional
environment with obstacles, which is modelled by 3D
Cartesian grid system. Path planning for UAVs require the
computational intelligence methods to move aerial vehicles along the
flight path effectively to target while avoiding obstacles. In this paper
Modified Particle Swarm Optimization (MPSO) algorithm is applied
to generate the optimal collision free 3D flight path for UAV. The
simulations results clearly demonstrate effectiveness of the proposed
algorithm in guiding UAV to the final destination by providing
optimal feasible path quickly and effectively.
Abstract: Distance learning systems offer useful methods of
learning and usually contain a final course test or another form of
test. The paper proposes a web application for evaluating tests using
an expert system in distance learning systems. The proposed web
application is appropriate for didactic tests or tests with results for
subsequent studying follow-up courses. The web application works
with test questions and uses an expert system and LFLC tool for test
evaluation. After test evaluation, the results are visualized and shown
to the student.
Abstract: The article includes the results and conclusions from
empirical researches that had been done. The research focuses on the
impact of investments made in small and medium-sized enterprises
financed from EU funds on the competitiveness of these companies.
The researches includes financial results in sales revenue and net
income, expenses, and many other new products/services on offer,
higher quality products and services, more modern methods of
production, innovation in management processes, increase in the
number of customers, increase in market share, increase in
profitability of production and provision of services. The main
conclusions are that, companies with direct investments under this
measure shall apply the modern methods of production. The
consequence of this is to increase the quality of our products and
services. Furthermore, both small and medium-sized enterprises have
introduced new products and services. Investments were carried out,
thus enabling better work organization in enterprises. Entrepreneurs
would guarantee higher quality of service, which would result in
better relationships with their customers, what is more, noting the rise
in number of clients. More than half of the companies indicated that
the investments contributed to the increase in market share. Same
thing as for market reach and brand recognition of particular
company. An interesting finding is that, investments in small
enterprises were more effective than medium-sized enterprises.
Abstract: Economic development and growth are significantly
linked to the consistent and sustainable sector of small and medium
enterprises (SMEs). Banks are the frontrunners in financing and
advising SMEs. The main objective of the study is to assess the
tendency of SMEs to use the Islamic bank. Model was developed
using quantitative method with a hypothetical-deductive testing
approach. Model (N = 364) used primary data on the tendency of
SMEs to use Islamic banks gathered from questionnaire. It is found
by Mann-Whitney test that the tendency to use Islamic bank varies
between those firms which consider formal financing with the ones
relying on informal financing with the latter tends more to use
Islamic bank. This study can serve academic researchers, policy
makers, and developing countries as a model of SMEs’ desirability to
Islamic banking.
Abstract: The contemporary battlefield creates a demand for
more costly and highly advanced munitions. Training personnel
responsible for operations as well as immediate execution of combat
tasks which engage real asset is unrealistic and economically not
feasible. Owing to a wide array of exploited simulators and various
types of imitators, it is possible to reduce the costs. One of the
effective elements of training, which can be applied in the training of
all service branches, is imitator of aerial targets. This research serves
as an introduction to the commencement of design analysis over a
real aerial target imitator. Within the project, the basic aerodynamic
calculations were made, which enabled to determine its geometry,
design layout, performance as well as mass balance of individual
components. The conducted calculations of the parameters of flight
characteristics come closer to the real performance of such
Unmanned Aerial Vehicles.
Abstract: Brain-Computer Interfaces (BCIs) measure brain
signals activity, intentionally and unintentionally induced by users,
and provides a communication channel without depending on the
brain’s normal peripheral nerves and muscles output pathway.
Feature Selection (FS) is a global optimization machine learning
problem that reduces features, removes irrelevant and noisy data
resulting in acceptable recognition accuracy. It is a vital step
affecting pattern recognition system performance. This study presents
a new Binary Particle Swarm Optimization (BPSO) based feature
selection algorithm. Multi-layer Perceptron Neural Network
(MLPNN) classifier with backpropagation training algorithm and
Levenberg-Marquardt training algorithm classify selected features.
Abstract: This study was conducted to investigate the
psychological variables motivating sport participation and
involvement among student-athletes of tertiary institutions in southwest
Nigeria. One thousand three hundred and fifty (N-1350) studentathletes
were randomly selected in all sports from nine tertiary
institutions in south-west Nigeria. These tertiary institutions include
University of Lagos, Lagos State University, Obafemi Awolowo
University, Osun State University, University of Ibadan, University
of Agriculture Abeokuta, Federal University of Technology
Akungba, University of Ilorin, and Kwara State University. The
descriptive survey research method was adopted while a self
developed validated Likert type questionnaire named Sport
Participation Scale (SPS) was used to elicit opinion from
respondents. The test-retest reliability value obtained for the
instrument, using Pearson Product Moment Correlation Co-efficient
was 0.96. Out of the one thousand three hundred and fifty (N-1350)
questionnaire administered, only one thousand two hundred and five
(N-1286) were correctly filled, coded and analysed using inferential
statistics of Chi-Square (X2) while all the tested hypotheses were set
at. 05 alpha level. Based on the findings of this study, the result
revealed that several psychological factors influence student athletes
to continue participation in sport one which includes love for the
game, famous athletes as role model and family support. However,
the analysis further revealed that the stipends the student-athletes get
from their universities have no influence on their participation and
involvement in sport.
Abstract: Round addition differential fault analysis using
operation skipping for lightweight block ciphers with on-the-fly key
scheduling is presented. For 64-bit KLEIN, it is shown that only a pair
of correct and faulty ciphertexts can be used to derive the secret master
key. For PRESENT, one correct ciphertext and two faulty ciphertexts
are required to reconstruct the secret key. Furthermore, secret key
extraction is demonstrated for the LBlock Feistel-type lightweight
block cipher.
Abstract: The ultimate purpose of this investigation was to
determine the teachers’ opinions as well as students’ opinions
towards the Adapted English Lessons. The subjects of the study were
5 Thai teachers, who teach English, and 85 Grade 10 mixed-ability
students at Triamudom Suksa Pattanakarn Ratchada School,
Bangkok, Thailand. The research instruments included questionnaires
and the informal interview. The data from the research instruments
was collected and analyzed concerning linguistic principles of
minimal pair and articulatory phonetics as well as teaching
techniques of mimicry-memorization; vocabulary substitution drills,
language pattern drills, reading comprehension exercise, practicing
listening, speaking and writing skill and communicative activities;
informal talk and free writing. The data was statistically compiled
according to an arithmetic percentage. The results showed that the
teachers and students have very highly positive opinions towards
adapting linguistic principles for teaching and learning phonological
accuracy. Teaching techniques provided in the Adapted English
Lessons can be used efficiently in the classroom. The teachers and
students have positive opinions towards them too.
Abstract: In present study, a large deposit of oolitic iron ore of
Late Carboniferous-Permotriassic-Lower Jurassic age was discovered
in Wadi Halfa and Argein areas, North Sudan. It seems that the iron
ore mineralization exists in the west and east bank of the River Nile
of the study area that are found on the Egyptian-Sudanese border.
The Carboniferous-Lower Jurassic age strata were covered by 67
sections and each section has been examined and carefully described.
The iron-ore in Wadi Halfa occurs as oolitic ironstone and contained
two horizons: (A) horizon and (B) horizon. Only horizon (A) was
observed in southern Argein area. The texture of the ore is variable
depending on the volume of the component. In thin sections, the
average of the ooids was ranged between 90%-80%. The matrix
varies between 10%-20% by volume and detritus quartz in other
component my reach up to 30% by volume in sandy massive ore.
Ooids size ranges from 0.2mm-1.00 mm on average in very coarse
ooids may attend up to 1 mm in size. The matrix around the ooids is
dominated by iron hydroxide, carbonate, fine, and amorphous silica.
The probable ore reserve estimate of 1.234 billion at a head grade of
41.29% Fe for the Wadi Halfa Oolitic Ironstone Formation. The iron
ore shows higher content of phosphorus ranges from 6.15% to 0.16%,
with mean 1.45%. The new technology Hatch–Ironstone Chloride
Segregation (HICS) can be used to produce commercial-quality of
iron and reduce phosphorus and silica to acceptable levels for steel
industry. The presence of infrastructures in addition to the presence
of massive quantities of iron ore would make exploitation
economically.
Abstract: The objective of this study was to synthesize and
characterize the poly(alkenoic acid)s with different molecular
structures, use these polymers to formulate a dental cement
restorative, and study the effect of molecular structures on reaction
kinetics, viscosity, and mechanical strengths of the formed polymers
and cement restoratives. In this study, poly(alkenoic acid)s with
different molecular structures were synthesized. The purified
polymers were formulated with commercial Fuji II LC glass fillers to
form the experimental cement restoratives. The reaction kinetics was
studied via 1HNMR spectroscopy. The formed restoratives were
evaluated using compressive strength, diametral tensile strength,
flexural strength, hardness and wear-resistance tests. Specimens were
conditioned in distilled water at 37oC for 24 h prior to testing. Fuji II
LC restorative was used as control. The results show that the higher
the arm number and initiator concentration, the faster the reaction
was. It was also found that the higher the arm number and branching
that the polymer had, the lower the viscosity of the polymer in water
and the lower the mechanical strengths of the formed restorative. The
experimental restoratives were 31-53% in compressive strength, 37-
55% in compressive modulus, 80-126% in diametral tensile strength,
76-94% in flexural strength, 4-21% in fracture toughness and 53-96%
in hardness higher than Fuji II LC. For wear test, the experimental
restoratives were only 5.4-13% of abrasive and 6.4-12% of attritional
wear depths of Fuji II LC in each wear cycle. The aging study also
showed that all the experimental restoratives increased their strength
continuously during 30 days, unlike Fuji II LC. It is concluded that
polymer molecular structures have significant and positive impact on
mechanical properties of dental cement restoratives.
Abstract: Increasingly complex modern power systems require
stability, especially for transient and small disturbances. Transient
stability plays a major role in stability during fault and large
disturbance. This paper compares a power system stabilizer (PSS)
and static Var compensator (SVC) to improve damping oscillation
and enhance transient stability. The effectiveness of a PSS connected
to the exciter and/or governor in damping electromechanical
oscillations of isolated synchronous generator was tested. The SVC
device is a member of the shunt FACTS (flexible alternating current
transmission system) family, utilized in power transmission systems.
The designed model was tested with a multi-machine system
consisting of four machines six bus, using MATLAB/SIMULINK
software. The results obtained indicate that SVC solutions are better
than PSS.
Abstract: Background: To improve the delivery of paediatric
healthcare in low resource settings, Community Health Workers
(CHW) have been provided with a paper-based set of protocols
known as Community Case Management (CCM). Yet research has
shown that CHW adherence to CCM guidelines is poor, ultimately
impacting health service delivery. Digitising the CCM guidelines via
mobile technology is argued in extant literature to improve CHW
adherence. However, little research exist which outlines how (a) this
process can be digitised and (b) adherence could be improved as a
result. Aim: To explore how an electronic mobile version of CCM
(eCCM) can overcome issues associated with the paper-based CCM
protocol (inadequate adherence to guidelines) vis-à-vis service
blueprinting. This service blueprint will outline how (a) the CCM
process can be digitised using mobile Clinical Decision Support
Systems software to support clinical decision-making and (b)
adherence can be improved as a result. Method: Development of a
single service blueprint for a standalone application which visually
depicts the service processes (eCCM) when supporting the CHWs,
using an application known as Supporting LIFE (SL eCCM app) as
an exemplar. Results: A service blueprint is developed which
illustrates how the SL eCCM app can be utilised by CHWs to assist
with the delivery of healthcare services to children. Leveraging
smartphone technologies can (a) provide CHWs with just-in-time
data to assist with their decision making at the point-of-care and (b)
improve CHW adherence to CCM guidelines. Conclusions: The
development of the eCCM opens up opportunities for the CHWs to
leverage the inherent benefit of mobile devices to assist them with
health service delivery in rural settings. To ensure that benefits are
achieved, it is imperative to comprehend the functionality and form
of the eCCM service process. By creating such a service blueprint for
an eCCM approach, CHWs are provided with a clear picture
regarding the role of the eCCM solution, often resulting in buy-in
from the end-users.
Abstract: Cancer is still one of the serious diseases threatening
the lives of human beings. How to have an early diagnosis and
effective treatment for tumors is a very important issue. The animal
carcinoma model can provide a simulation tool for the studies of
pathogenesis, biological characteristics, and therapeutic effects.
Recently, drug delivery systems have been rapidly developed to
effectively improve the therapeutic effects. Liposome plays an
increasingly important role in clinical diagnosis and therapy for
delivering a pharmaceutic or contrast agent to the targeted sites.
Liposome can be absorbed and excreted by the human body, and is
well known that no harm to the human body. This study aimed to
compare the therapeutic effects between encapsulated (doxorubicin
liposomal, Lipodox) and un-encapsulated (doxorubicin, Dox)
anti-tumor drugs using magnetic resonance imaging (MRI).
Twenty-four New Zealand rabbits implanted with VX2 carcinoma at
left thighs were classified into three groups: control group (untreated),
Dox-treated group, and LipoDox-treated group, 8 rabbits for each
group. MRI scans were performed three days after tumor implantation.
A 1.5T GE Signa HDxt whole body MRI scanner with a high
resolution knee coil was used in this study. After a 3-plane localizer
scan was performed, three-dimensional (3D) fast spin echo (FSE)
T2-weighted Images (T2WI) was used for tumor volumetric
quantification. Afterwards, two-dimensional (2D) spoiled gradient
recalled echo (SPGR) dynamic contrast-enhanced (DCE) MRI was
used for tumor perfusion evaluation. DCE-MRI was designed to
acquire four baseline images, followed by contrast agent Gd-DOTA
injection through the ear vein of rabbit. A series of 32 images were
acquired to observe the signals change over time in the tumor and
muscle. The MRI scanning was scheduled on a weekly basis for a
period of four weeks to observe the tumor progression longitudinally.
The Dox and LipoDox treatments were prescribed 3 times in the first
week immediately after the first MRI scan; i.e. 3 days after VX2 tumor
implantation. ImageJ was used to quantitate tumor volume and time
course signal enhancement on DCE images. The changes of tumor size
showed that the growth of VX2 tumors was effectively inhibited for
both LipoDox-treated and Dox-treated groups. Furthermore, the tumor
volume of LipoDox-treated group was significantly lower than that of
Dox-treated group, which implies that LipoDox has better therapeutic effect than Dox. The signal intensity of LipoDox-treated group is
significantly lower than that of the other two groups, which implies
that targeted therapeutic drug remained in the tumor tissue. This study
provides a radiation-free and non-invasive MRI method for
therapeutic monitoring of targeted liposome on an animal tumor
model.
Abstract: South Africa is in its post-industrial era moving from
the primary and secondary sector to the tertiary sector. The study
investigated the impact of the disaggregated energy consumption
(coal, oil, and electricity) on the primary, secondary and tertiary
sectors of the economy between 1980 and 2012 in South Africa.
Using vector error correction model, it was established that South
Africa is an energy dependent economy, and that energy (especially
electricity and oil) is a limiting factor of growth. This implies that
implementation of energy conservation policies may hamper
economic growth. Output growth is significantly outpacing energy
supply, which has necessitated load shedding. To meet up the excess
energy demand, there is a need to increase the generating capacity
which will necessitate increased investment in the electricity sector as
well as strategic steps to increase oil production. There is also need to
explore more renewable energy sources, in order to meet the growing
energy demand without compromising growth and environmental
sustainability. Policy makers should also pursue energy efficiency
policies especially at sectoral level of the economy.
Abstract: The aim of this study is to empirically investigate the
mediating impact of export performance (EP) between technological
advancement capabilities and business performance (BP) of
Malaysian manufacturing micro, small and medium sized enterprises
(MSME’s). Firm’s technological advancement resources are
hypothesized as a platform to enhance both exports and BP of
manufacturing MSMEs in Malaysia. This study is twofold, primary it
has investigated that technological advancement capabilities helps to
appreciates main performance measures noted in terms of EP and
Secondly, it investigates that how efficiently and effectively
technological advancement capabilities can contribute in overall
Malaysian MSME’s BP. Smart PLS-3 statistical software is used to
know the association between technological advancement
capabilities, MSME’s EP and BP. In this study, the data was
composed from Malaysian manufacturing MSME’s in east coast
industrial zones known as the manufacturing hub of MSMEs. Seven
hundred and fifty (750) questionnaires were distributed, but only 148
usable questionnaires are returned. The finding of this study indicated
that technological advancement capabilities helps to strengthen the
export in term of time and cost efficient and it plays a significant role
in appreciating their BP. This study is helpful for small and medium
enterprise owners who intend to expand their business overseas and
though smart technological advancement resources they can achieve
their business competitiveness and excellence both at local and
international markets.
Abstract: Mixed-use development is one of the most important
trends in new island house transformation along southeast coastal area
in China. Unique island geographical environment and profound
fishing village culture coexist for a long time in this. With artistic
creation for the purpose of the "live-work" houses are in a large
number of emergence, however, still lack of systematic strategy.
Based on space effect from marine resources to regional human
settlements, this article teases out the evolution regularity of island
settlement context and architectural form, then, puts forward the
formation mechanism and construction model of art island houses.
Thereby, to further explore space design method and site creation
strategy of mixed-use development.
Abstract: Presently various computational techniques are used
in modeling and analyzing environmental engineering data. In the
present study, an intra-comparison of polynomial and radial basis
kernel functions based on Support Vector Regression and, in turn, an
inter-comparison with Multi Linear Regression has been attempted in
modeling mass transfer capacity of vertical (θ = 90O) and inclined (θ
multiple plunging jets (varying from 1 to 16 numbers). The data set
used in this study consists of four input parameters with a total of
eighty eight cases, forty four each for vertical and inclined multiple
plunging jets. For testing, tenfold cross validation was used.
Correlation coefficient values of 0.971 and 0.981 along with
corresponding root mean square error values of 0.0025 and 0.0020
were achieved by using polynomial and radial basis kernel functions
based Support Vector Regression respectively. An intra-comparison
suggests improved performance by radial basis function in
comparison to polynomial kernel based Support Vector Regression.
Further, an inter-comparison with Multi Linear Regression
(correlation coefficient = 0.973 and root mean square error = 0.0024)
reveals that radial basis kernel functions based Support Vector
Regression performs better in modeling and estimating mass transfer
by multiple plunging jets.