Abstract: In this paper, we present a framework to determine Haar solutions of Bratu-type equations that are widely applicable in fuel ignition of the combustion theory and heat transfer. The method is proposed by applying Haar series for the highest derivatives and integrate the series. Several examples are given to confirm the efficiency and the accuracy of the proposed algorithm. The results show that the proposed way is quite reasonable when compared to exact solution.
Abstract: Sample of CsAg2I3 was prepared by solid state reaction. Then, microstructure parameters of this sample have been determined using wide angle X-ray scattering WAXS method. As well as, Cell parameters of crystal structure have been refined using CHEKCELL program. This analysis states that the lattice intrinsic strainof the sample is so small and the crystal size is on the order of 559Å.
Abstract: Samples of CoFe2-xCrxO4 where x varies from 0.0 to 0.5 were prepared by co-precipitation route. These samples were sintered at 750°C for 2 hours. These particles were characterized by X-ray diffraction (XRD) at room temperature. The FCC spinel structure was confirmed by XRD patterns of the samples. The crystallite sizes of these particles were calculated from the most intense peak by Scherrer formula. The crystallite sizes lie in the range of 37-60 nm. The lattice parameter was found decreasing upon substitution of Cr. DC electrical resistivity was measured as a function of temperature. The room temperature thermoelectric power was measured for the prepared samples. The magnitude of Seebeck coefficient depends on the composition and resistivity of the samples.
Abstract: In this work Artificial Intelligence (AI) techniques like Fuzzy logic, Genetic Algorithms and Particle Swarm Optimization have been used to improve the performance of the Automatic Generation Control (AGC) system. Instead of applying Genetic Algorithms and Particle swarm optimization independently for optimizing the parameters of the conventional AGC with PI controller, an intelligent tuned Fuzzy logic controller (acting as the secondary controller in the AGC system) has been designed. The controller gives an improved dynamic performance for both hydrothermal and thermal-thermal power systems under a variety of operating conditions.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: Carbon nanotubes (CNTs) are attractive because of
their excellent chemical durability mechanical strength and electrical
properties. Therefore there is interest in CNTs for not only electrical
and mechanical application, but also biological and medical
application.
In this study, the dispersion power of surfactant-treated multiwalled
carbon nanotubes (MWCNTs) and their effect on the antibacterial
activity were examined. Surfactant was used sodium
dodecyl-benzenesulfonate (SDBS). UV-vis absorbance and
transmission electron microscopy(TEM) were used to characterize the
dispersion of MWCNTs in the aqueous phase, showing that the
surfactant molecules had been adsorbed onto the MWCNTs surface.
The surfactant-treated MWCNTs exhibited antimicrobial activities
to streptococcus mutans. The optical density growth curves and viable
cell number determined by the plating method suggested that the
antimicrobial activity of surfactant-treated MWCNTs was both
concentration and treatment time-dependent.
Abstract: To simulate heating systems in buildings, a research oriented computer code has been developed in Sharif University of Technology in Iran where the climate, existing heating equipment in buildings, consumer behavior and their interactions are considered for simulating energy consumption in conventional systems such as heaters, radiators and fan-coils. In order to validate the computer code, the available data of five buildings was used and the computed consumed energy was compared with the estimated energy extracted from monthly bills. The initial heating system was replaced by the alternative system and the effect of this change was observed on the energy consumption. As a result, the effect of changing heating equipment on energy consumption was investigated in different climates. Changing heater to radiator renders energy conservation up to 50% in all climates and changing radiator to fan-coil decreases energy consumption in climates with cold and dry winter.
Abstract: Transportation is of great importance in the current
life of human beings. The transportation system plays many roles,
from economical development to after-catastrophe aids such as
rescue operation in the first hours and days after an earthquake. In
after earthquakes response phase, transportation system acts as a
basis for ground operations including rescue and relief operation,
food providing for victims and etc. It is obvious that partial or
complete obstruction of this system results in the stop of these
operations. Bridges are one of the most important elements of
transportation network. Failure of a bridge, in the most optimistic
case, cuts the relation between two regions and in more developed
countries, cuts the relation of numerous regions. In this paper, to
evaluate the vulnerability and estimate the damage level of Tehran
bridges, HAZUS method, developed by Federal Emergency
Management Agency (FEMA) with the aid of National Institute of
Building Science (NIBS), is used for the first time in Iran. In this
method, to evaluate the collapse probability, fragility curves are
used. Iran is located on seismic belt and thus, it is vulnerable to
earthquakes. Thus, the study of the probability of bridge collapses, as
an important part of transportation system, during earthquakes is of
great importance. The purpose of this study is to provide fragility
curves for Gisha Bridge, one of the longest steel bridges in Tehran,
as an important lifeline element. Besides, the damage probability for
this bridge during a specific earthquake, introduced as scenario
earthquakes, is calculated. The fragility curves show that for the
considered scenario, the probability of occurrence of complete
collapse for the bridge is 8.6%.
Abstract: The modified Arcan fixture was used in order to
investigate the mixed mode fracture properties of high strength steel
butt weld through experimental and numerical analysis. The fixture
consisted of a central section with "butterfly-shaped" specimen that
had central crack. The specimens were under pure mode I (opening),
pure mode II (shearing) and all in plane mixed mode loading angles
starting from 0 to 90 degrees. The geometric calibration factors were
calculated with the aid of finite element analysis for various loading
mode and different crack length (0.45≤ a/w ≤0.55) and the critical
fracture loads obtained experimentally. The critical fracture
toughness (KIC & KIIC) estimated with experimental and numerical
analysis under mixed mode loading conditions.
Abstract: Non-Destructive evaluation of in-service power
transformer condition is necessary for avoiding catastrophic failures.
Dissolved Gas Analysis (DGA) is one of the important methods.
Traditional, statistical and intelligent DGA approaches have been
adopted for accurate classification of incipient fault sources.
Unfortunately, there are not often enough faulty patterns required for
sufficient training of intelligent systems. By bootstrapping the
shortcoming is expected to be alleviated and algorithms with better
classification success rates to be obtained. In this paper the
performance of an artificial neural network, K-Nearest Neighbour
and support vector machine methods using bootstrapped data are
detailed and shown that while the success rate of the ANN algorithms
improves remarkably, the outcome of the others do not benefit so
much from the provided enlarged data space. For assessment, two
databases are employed: IEC TC10 and a dataset collected from
reported data in papers. High average test success rate well exhibits
the remarkable outcome.
Abstract: As chip manufacturing technology is suddenly on the
threshold of major evaluation, which shrinks chip in size and
performance, LFSR (Linear Feedback Shift Register) is implemented
in layout level which develops the low power consumption chip,
using recent CMOS, sub-micrometer layout tools. Thus LFSR
counter can be a new trend setter in cryptography and is also
beneficial as compared to GRAY & BINARY counter and variety of
other applications.
This paper compares 3 architectures in terms of the hardware
implementation, CMOS layout and power consumption, using
Microwind CMOS layout tool. Thus it provides solution to a low
power architecture implementation of LFSR in CMOS VLSI.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: Discharges in hydrogen, ignited by wire explosion, with current amplitude up to 1.5 MA were investigated. Channel diameter oscillations were observed on the photostreaks. Voltage and current curves correlated with the photostreaks. At initial gas pressure of 5-35 MPa the oscillation period was proportional to square root of atomic number of the initiating wire material. These oscillations were associated with aligned magnetic and gas-kinetic pressures. At initial pressure of 80-160 MPa acoustic pressure fluctuations on the discharge chamber wall were increased up to 150 MPa and there were the growth of voltage fluctuations on the discharge gap up to 3 kV simultaneously with it. In some experiments it was observed abrupt increase in the oscillation amplitude, which can be caused by the resonance of the acoustic oscillations in discharge chamber volume and the oscillations connected with alignment of the gaskinetic pressure and the magnetic pressure, as far as frequencies of these oscillations are close to each other in accordance with the estimates and the experimental data. Resonance of different type oscillations can produce energy density increasing in the discharge channel. Thus, the appropriate initial conditions in the experiment allow to increase the energy density in the discharge channel
Abstract: Soil microbial activity is adversely affected by pollutants such as heavy metals, antibiotics and pesticides. Organic amendments including sewage sludge, municipal compost and vermicompost are recently used to improve soil structure and fertility. But, these materials contain heavy metals including Pb, Cd, Zn, Ni and Cu that are toxic to soil microorganisms and may lead to occurrence of more tolerant microbes. Among these, Pb is the most abundant and has more negative effect on soil microbial ecology. In this study, Pb levels of 0, 100, 200, 300, 400 and 500 mg Pb [as Pb(NO3)2] per kg soil were added to the pots containing 2 kg of a loamy soil and incubated for 6 months at 25°C with soil moisture of - 0.3 MPa. Dehydrogenase activity of soil as a measure of microbial activity was determined on 15, 30, 90 and 180 days after incubation. Triphenyl tetrazolium chloride (TTC) was used as an electron acceptor in this assay. PICTs (IC50 values) were calculated for each Pb level and incubation time. Soil microbial activity was decreased by increasing Pb level during 30 days of incubation but the induced tolerance appeared on day 90 and thereafter. During 90 to 180 days of incubation, the PICT was gradually developed by increasing Pb level up to 200 mg kg-1, but the rate of enhancement was steeper at higher concentrations.
Abstract: Collective action can be an effective means for local development as well as important strategy to enhance livelihoods especially among rural people. This article explores the level of collective action among members of Fishermen-s Wives Group (KUNITA) in Malaysia. KUNITA was established by the Malaysian Fishery Development Authority (LKIM) with an objective to increase the socio-economic status of fishermen-s families. The members who are mostly the wives and daughters of fishermen are strongly encouraged by LKIM to venture into entrepreneurship activities. The objective of this research was to see the level of collective action among members in KUNITA groups in the state of Selangor. The finding shows that high level of collective action among KUNITA members is strongly based on volunteerism. However, the level of cooperation among members in the group is relatively low. The findings present significant challenges for the group in maintaining the sustainability of KUNITA organization.
Abstract: In order to evaluate the relationship between the sulphur (S), glucose (G), nitrogen (N) and plant residues (st), sulphur immobilization and microbial transformation were monitored in five soil samples from 0-30 cm of Bastam farmers fields of Shahrood area following 11 treatments with different levels of Sulphur (S), glucose (G), N and plant residues (wheat straw) in a randomized block design with three replications and incubated over 20, 45 and 60 days, the immobilization of SO4 -2-S presented as a percentage of that added, was inversely related to its addition rate. Additions of glucose and plant residues increased with the C-to-S ratio of the added amendments, irrespective of their origins (glucose and plant residues). In the presence of C sources (glucose or plant residues). N significantly increased the immobilization of SO4 -2-S, whilst the effect of N was insignificant in the absence of a C amendment. In first few days the amounts of added SO4 -2-S immobilized were linearly correlated with the amounts of added S recovered in the soil microbial biomass. With further incubation the proportions of immobilized SO4 -2-S remaining as biomass-S decreased. Decrease in biomass-S was thought to be due to the conversion of biomass-S into soil organic-S. Glucose addition increased the immobilization (microbial utilization and incorporation into the soil organic matter) of native soil SO4 -2-S. However, N addition enhance the mineralization of soil organic-S, increasing the concentration of SO4 - 2-S in soil.
Abstract: The limit load carrying capacity of functionally
graded materials (FGM) circular plates subjected to an arbitrary
rotationally symmetric loading has been computed. It is provided that
the plate material behaves rigid perfectly plastic and obeys either the
Square or the Tresca yield criterion. To this end the upper and lower
bound principles of limit analysis are employed to determine the
exact value for the limiting load. The correctness of the result are
verified and finally limiting loads for two examples namely; through
radius and through thickness FGM circular plates with simply
supported edges are calculated, respectively and moreover, the values
of critical loading factor are determined.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: The forest fires in Thailand are annual occurrence which is the cause of air pollutions. This study intended to estimate the emission from forest fire during 2005-2009 using MODerateresolution Imaging Spectro-radiometer (MODIS) sensor aboard the Terra and Aqua satellites, experimental data, and statistical data. The forest fire emission is estimated using equation established by Seiler and Crutzen in 1982. The spatial and temporal variation of forest fire emission is analyzed and displayed in the form of grid density map. From the satellite data analysis suggested between 2005 and 2009, the number of fire hotspots occurred 86,877 fire hotspots with a significant highest (more than 80% of fire hotspots) in the deciduous forest. The peak period of the forest fire is in January to May. The estimation on the emissions from forest fires during 2005 to 2009 indicated that the amount of CO, CO2, CH4, and N2O was about 3,133,845 tons, 47,610.337 tons, 204,905 tons, and 6,027 tons, respectively, or about 6,171,264 tons of CO2eq. They also emitted 256,132 tons of PM10. The year 2007 was found to be the year when the emissions were the largest. Annually, March is the period that has the maximum amount of forest fire emissions. The areas with high density of forest fire emission were the forests situated in the northern, the western, and the upper northeastern parts of the country.
Abstract: The present study is aim to prepare and evaluate the selfnanoemulsifying drug delivery (SNEDDS) system of a poorly water soluble drug valsartan in order to achieve a better dissolution rate which would further help in enhancing oral bioavailability. The present research work describes a SNEDDS of valsartan using labrafil M 1944 CS, Tween 80 and Transcutol HP. The pseudoternary phase diagrams with presence and absence of drug were plotted to check for the emulsification range and also to evaluate the effect of valsartan on the emulsification behavior of the phases. The mixtures consisting of oil (labrafil M 1944 CS) with surfactant (tween 80), co-surfactant (Transcutol HP) were found to be optimum formulations. Prepared formulations were evaluated for its particle size distribution, nanoemulsifying properties, robustness to dilution, self emulsication time, turbidity measurement, drug content and invitro dissolution. The optimized formulations are further evaluated for heating cooling cycle, centrifugation studies, freeze thaw cycling, particle size distribution and zeta potential were carried out to confirm the stability of the formed SNEDDS formulations. The prepared formulation revealed t a significant improvement in terms of the drug solubility as compared with marketed tablet and pure drug.