Abstract: Rivers have transient storage or dead zones where
injected pollutants or solutes are entrapped for considerable period of
time, known as residence time, before being released into the main
flowing zones of rivers. In this study, a new empirical expression for
residence time, implementing genetic programming on published
dispersion data, has been derived. The proposed expression uses few
hydraulic and geometric characteristics of rivers which are normally
known to the authorities. When compared with some reported
expressions, based on various statistical indices, it can be concluded
that the proposed expression predicts the residence time of pollutants
in natural rivers more accurately.
Abstract: This study evaluated the acute toxicity and tissue
distribution of intravenously administered gold nanoparticles
(AuNPs) in male rabbits. Rabbits were exposed to single dose of
AuNPs (300 μg/ kg). Toxic effects were assessed via general
behavior, hematological parameters, serum biochemical parameters,
and histopathological examination of various rabbits’ organs.
Inductively coupled plasma–mass spectrometry (ICP-MS) was used
to determine gold concentrations in tissue samples collected at
predetermined time intervals. After one week, AuNPs exerted no
obvious acute toxicity in rabbits. However, inflammatory reactions
were observed in liver, lungs and kidneys accompanied with mild
absolute neutrophilia and significant monocytosis. The highest gold
levels were found in the spleen and liver followed by lungs, and
kidneys. These results indicated that AuNPs could be distributed
extensively to various tissues in the body, but primarily in the spleen
and liver.
Abstract: With the introduction of cash-less society policy by
the Central Bank of Nigeria, the concept of e-banking services have
over the years’ experience a significant improvement. Today quite a
number of people are embracing e-banking activities especially
ATM, thereby moving away from the conventional banking system.
This paper presents a review of the underlying Architectural Layout
of Intra-Bank and Inter-Bank ATM connectivity in Nigeria. The
paper further investigates and discusses factors affecting the Intra-
Bank and Inter-Bank ATM connectivity in Nigeria. In addition, as
well possible solutions to these factors affecting ATM Connectivity
and Operations are proposed.
Abstract: This study investigates how the site specific traffic
data differs from the Mechanistic Empirical Pavement Design
Software default values. Two Weigh-in-Motion (WIM) stations were
installed in Interstate-40 (I-40) and Interstate-25 (I-25) to developed
site specific data. A computer program named WIM Data Analysis
Software (WIMDAS) was developed using Microsoft C-Sharp (.Net)
for quality checking and processing of raw WIM data. A complete
year data from November 2013 to October 2014 was analyzed using
the developed WIM Data Analysis Program. After that, the vehicle
class distribution, directional distribution, lane distribution, monthly
adjustment factor, hourly distribution, axle load spectra, average
number of axle per vehicle, axle spacing, lateral wander distribution,
and wheelbase distribution were calculated. Then a comparative
study was done between measured data and AASHTOWare default
values. It was found that the measured general traffic inputs for I-40
and I-25 significantly differ from the default values.
Abstract: Increase of emergency incidents and crisis situations
requires proactive crisis management of authorities and for its
solution. Application Business Continuity Management helps the
crisis management authorities to quickly and responsibly respond to
threats. It also helps effectively and efficiently planning powers and
resources. The main goal of this article is describing Military
Continuity Management System (MCMS) based on the principles of
Business Continuity Management System (BCMS) for dealing with
floods in the territory of the selected municipalities. There are
explained steps of loading, running and evaluating activities in the
software application MCMS. Software MCMS provides complete
control over the tasks, contribute a comprehensive and responsible
approach solutions to solution floods in the municipality.
Abstract: Ensuring of continuity of business is basic strategy of
every company. Continuity of organization activities includes
comprehensive procedures that help in solving unexpected situations
of natural and anthropogenic character (for example flood, blaze,
economic situations). Planning of continuity operations is a process
that helps identify critical processes and implement plans for the
security and recovery of key processes. The aim of this article is to
demonstrate application of system approach to managing business
continuity called business continuity management systems in military
issues. This article describes the life cycle of business continuity
management which is based on the established cycle PDCA (Plan-
Do-Check-Act). After this is carried out by activities which are
making by University of Defence during activation of forces and
means of the integrated rescue system in case of emergencies -
accidents at a nuclear power plant in Czech Republic. Activities of
various stages of deployment earmarked forces and resources are
managed and evaluated by using MCMS application (Military
Continuity Management System).
Abstract: In this study, the time-dependent behavior of damaged
reinforced concrete shear wall structures strengthened with composite
plates having variable fibers spacing was investigated to analyze their
seismic response. In the analytical formulation, the adherent and the
adhesive layers are all modeled as shear walls, using the mixed Finite
Element Method (FEM). The anisotropic damage model is adopted to
describe the damage extent of the Reinforced Concrete shear walls.
The phenomenon of creep and shrinkage of concrete has been
determined by Eurocode 2. Large earthquakes recorded in Algeria
(El-Asnam and Boumerdes) have been tested to demonstrate the
accuracy of the proposed method. Numerical results are obtained for non-uniform distributions of
carbon fibers in epoxy matrices. The effects of damage extent and the
delay mechanism creep and shrinkage of concrete are highlighted.
Prospects are being studied.
Abstract: Wireless networks are built upon the open shared
medium which makes easy for attackers to conduct malicious
activities. Jamming is one of the most serious security threats to
information economy and it must be dealt efficiently. Jammer
prevents legitimate data to reach the receiver side and also it
seriously degrades the network performance. The objective of this
paper is to provide a general overview of jamming in wireless
network. It covers relevant works, different jamming techniques,
various types of jammers and typical prevention techniques.
Challenges associated with comparing several anti-jamming
techniques are also highlighted.
Abstract: For the last decade, researchers have started to focus
their interest on Multicast Group Key Management Framework. The
central research challenge is secure and efficient group key
distribution. The present paper is based on the Bit model based
Secure Multicast Group key distribution scheme using the most
popular absolute encoder output type code named Gray Code. The
focus is of two folds. The first fold deals with the reduction of
computation complexity which is achieved in our scheme by
performing fewer multiplication operations during the key updating
process. To optimize the number of multiplication operations, an
O(1) time algorithm to multiply two N-bit binary numbers which
could be used in an N x N bit-model of reconfigurable mesh is used
in this proposed work. The second fold aims at reducing the amount
of information stored in the Group Center and group members while
performing the update operation in the key content. Comparative
analysis to illustrate the performance of various key distribution
schemes is shown in this paper and it has been observed that this
proposed algorithm reduces the computation and storage complexity
significantly. Our proposed algorithm is suitable for high
performance computing environment.
Abstract: As a result of the ambiguity and complexity
surrounding anaerobic digester foaming, efforts have been made by
various researchers to understand the process of anaerobic digester
foaming so as to proffer a solution that can be universally applied
rather than site specific. All attempts ranging from experimental
analysis to comparative review of other process has not fully
explained the conditions and process of foaming in anaerobic
digester. Studying the current available knowledge on foam
formation and relating it to anaerobic digester process and operating
condition, this piece of work presents a succinct and enhanced
understanding of foaming in anaerobic digesters as well as
introducing a simple method to identify the onset of anaerobic
digester foaming based on analysis of historical data from a field
scale system.
Abstract: In this article was evaluated the protective effect of
the alternative concrete obtained from the binary mixture of fly ash,
and iron and steel slag. After mixing the cement with aggregates,
structural steel was inserted in the matrix cementitious. The study
was conducted comparatively with specimens exposed to natural
conditions free of chloride ion. The chloride ion effect on the
specimens accelerated under controlled conditions (3.5% NaCl and
25°C temperature). The impedance data were acquired in a range of 1
mHz to 100 kHz.
Abstract: Routing in adhoc networks is a challenge as nodes are
mobile, and links are constantly created and broken. Present ondemand
adhoc routing algorithms initiate route discovery after a path
breaks, incurring significant cost to detect disconnection and
establish a new route. Specifically, when a path is about to be broken,
the source is warned of the likelihood of a disconnection. The source
then initiates path discovery early, avoiding disconnection totally. A
path is considered about to break when link availability decreases.
This study modifies Adhoc On-demand Multipath Distance Vector
routing (AOMDV) so that route handoff occurs through link
availability estimation.
Abstract: The fundamental issue in understanding the origin and
growth mechanism of nanomaterials, from a fundamental unit is a big
challenging problem to the scientists. Recently, an immense attention
is generated to the researchers for prediction of exceptionally stable
atomic cluster units as the building units for future smart materials.
The present study is a systematic investigation on the stability and
electronic properties of a series of bimetallic (semiconductor-alkaline
earth) clusters, viz., BxMg3 (x=1-5) is performed, in search for
exceptional and/ or unusual stable motifs. A very popular hybrid
exchange-correlation functional, B3LYP along with a higher basis
set, viz., 6-31+G[d,p] is employed for this purpose under the density
functional formalism. The magic stability among the concerned
clusters is explained using the jellium model. It is evident from the
present study that the magic stability of B4Mg3
cluster arises due to
the jellium shell closure.
Abstract: Synchrophasor technology is fast being deployed in
electric power grids all over the world and is fast changing the way
the grids are managed. This trend is to continue until the entire
power grids are fully connected so they can be monitored and
controlled in real-time. Much achievement has been made in the
synchrophasor technology development and deployment, and there
are still much more to be achieved. For instance, real-time power
grid control and protection potentials of synchrophasor are yet to be
explored. It is of necessity that researchers keep in view the various
challenges that still need to be overcome in expanding the frontiers
of synchrophasor technology. This paper outlines the major
challenges that should be dealt with in order to achieve the goal of
total power grid visualization, monitoring, and control using
synchrophasor technology.
Abstract: The liberalisation of the education industry has
exposed the institute of higher learning (IHL) in Malaysia to the
financial challenges. Without good financial standing, public
institution will rely on the government funding. Ostensibly, this
contradicts with the government’s aspiration to make universities
self-sufficient. With stiff competition from private institutes of higher
learning, IHL need to be prepared at the forefront level. The
corporate identity itself is the entrance to the world of higher learning
and it is in this uniqueness, it will be able to distinguish itself from
competitors. This paper examined the perception of the stakeholders
at one of the public universities in the east coast region in Malaysia
on the perceived reputation and how the university communicate its
preparedness for self-sustainability through corporate identity. The
findings indicated while the stakeholders embraced the challenges in
facing the stiff competition and struggling market conditions, most of
them felt the university should put more efforts in mobilising the
corporate identity to its constituencies.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: The use of solar energy as a source for pumping water
is one of the promising areas in the photovoltaic (PV) application.
The energy of photovoltaic pumping systems (PVPS) can be widely
improved by employing an MPPT algorithm. This will lead
consequently to maximize the electrical motor speed of the system.
This paper presents a modified incremental conductance (IncCond)
MPPT algorithm with direct control method applied to a standalone
PV pumping system. The influence of the algorithm parameters on
system behavior is investigated and compared with the traditional
(INC) method. The studied system consists of a PV panel, a DC-DC
boost converter, and a PMDC motor-pump. The simulation of the
system by MATLAB-SIMULINK is carried out. Simulation results
found are satisfactory.
Abstract: This paper is meant to analyze the ranking of
University of Malaysia Terengganu, UMT’s website in the World
Wide Web. There are only few researches have been done on
comparing the ranking of universities’ websites so this research will
be able to determine whether the existing UMT’s website is serving
its purpose which is to introduce UMT to the world. The ranking is
based on hub and authority values which are accordance to the
structure of the website. These values are computed using two websearching
algorithms, HITS and SALSA. Three other universities’
websites are used as the benchmarks which are UM, Harvard and
Stanford. The result is clearly showing that more work has to be done
on the existing UMT’s website where important pages according to
the benchmarks, do not exist in UMT’s pages. The ranking of UMT’s
website will act as a guideline for the web-developer to develop a
more efficient website.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: In this paper, a novel Linear Feedback Shift Register
(LFSR) with Look Ahead Clock Gating (LACG) technique is
presented to reduce the power consumption in modern processors
and System-on-Chip. Clock gating is a predominant technique used
to reduce unwanted switching of clock signals. Several clock gating
techniques to reduce the dynamic power have been developed, of
which LACG is predominant. LACG computes the clock enabling
signals of each flip-flop (FF) one cycle ahead of time, based on the
present cycle data of the flip-flops on which it depends. It overcomes
the timing problems in the existing clock gating methods like datadriven
clock gating and Auto-Gated flip-flops (AGFF) by allotting a
full clock cycle for the determination of the clock enabling signals.
Further to reduce the power consumption in LACG technique, FFs
can be grouped so that they share a common clock enabling signal.
Simulation results show that the novel grouped LFSR with LACG
achieves 15.03% power savings than conventional LFSR with LACG
and 44.87% than data-driven clock gating.