Abstract: The recent interest in alternative and renewable
energy systems results in increased installed capacity ratio of such
systems in total energy production of the world. Specifically, Wind
Energy Conversion Systems (WECS) draw significant attention
among possible alternative energy options, recently. On the contrary
of the positive points of penetrating WECS in all over the world in
terms of environment protection, energy independence of the
countries, etc., there are significant problems to be solved for the grid
connection of large scale WECS. The reactive power regulation,
voltage variation suppression, etc. can be presented as major issues to
be considered in this regard. Thus, this paper evaluates the
application of a Static VAr Compensator (SVC) unit for the reactive
power regulation and operation continuity of WECS during a fault
condition. The system is modeled employing the IEEE 13 node test
system. Thus, it is possible to evaluate the system performance with
an overall grid simulation model close to real grid systems. The
overall simulation model is developed in
MATLAB/Simulink/SimPowerSystems® environments and the
obtained results effectively match the target of the provided study.
Abstract: In this paper comprehensive studies have been carried
out for the design optimization of a waste heat recovery system for
effectively utilizing the domestic air conditioner heat energy for
producing hot water. Numerical studies have been carried for the
geometry optimization of a waste heat recovery system for domestic
air conditioners. Numerical computations have been carried out using
a validated 2d pressure based, unsteady, 2nd-order implicit, SST k-ω
turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. At identical inflow and boundary
conditions various geometries were tried and effort has been taken for
proposing the best design criteria. Several combinations of pipe line
shapes viz., straight and spiral with different number of coils for the
radiator have been attempted and accordingly the design criteria has
been proposed for the waste heat recovery system design. We have
concluded that, within the given envelope, the geometry optimization
is a meaningful objective for getting better performance of waste heat
recovery system for air conditioners.
Abstract: This paper presents the development, analysis and
implementation of an inverse polynomial numerical method which is
well suitable for solving initial value problems in first order ordinary
differential equations with applications to sample problems. We also
present some basic concepts and fundamental theories which are vital
to the analysis of the scheme. We analyzed the consistency,
convergence, and stability properties of the scheme. Numerical
experiments were carried out and the results compared with the
theoretical or exact solution and the algorithm was later coded using
MATLAB programming language.
Abstract: Particle size distribution, the most important
characteristics of aerosols, is obtained through electrical
characterization techniques. The dynamics of charged nanoparticles
under the influence of electric field in Electrical Mobility
Spectrometer (EMS) reveals the size distribution of these particles.
The accuracy of this measurement is influenced by flow conditions,
geometry, electric field and particle charging process, therefore by
the transfer function (transfer matrix) of the instrument. In this work,
a wire-cylinder corona charger was designed and the combined fielddiffusion
charging process of injected poly-disperse aerosol particles
was numerically simulated as a prerequisite for the study of a
multichannel EMS. The result, a cloud of particles with no uniform
charge distribution, was introduced to the EMS. The flow pattern and
electric field in the EMS were simulated using Computational Fluid
Dynamics (CFD) to obtain particle trajectories in the device and
therefore to calculate the reported signal by each electrometer.
According to the output signals (resulted from bombardment of
particles and transferring their charges as currents), we proposed a
modification to the size of detecting rings (which are connected to
electrometers) in order to evaluate particle size distributions more
accurately. Based on the capability of the system to transfer
information contents about size distribution of the injected particles,
we proposed a benchmark for the assessment of optimality of the
design. This method applies the concept of Von Neumann entropy
and borrows the definition of entropy from information theory
(Shannon entropy) to measure optimality. Entropy, according to the
Shannon entropy, is the ''average amount of information contained in
an event, sample or character extracted from a data stream''.
Evaluating the responses (signals) which were obtained via various
configurations of detecting rings, the best configuration which gave
the best predictions about the size distributions of injected particles,
was the modified configuration. It was also the one that had the
maximum amount of entropy. A reasonable consistency was also
observed between the accuracy of the predictions and the entropy
content of each configuration. In this method, entropy is extracted
from the transfer matrix of the instrument for each configuration.
Ultimately, various clouds of particles were introduced to the
simulations and predicted size distributions were compared to the
exact size distributions.
Abstract: Spacer grid assembly supporting the nuclear fuel rods
is an important concern in the design of structural components of a
Pressurized Water Reactor (PWR). The spacer grid is composed by
springs and dimples which are formed from a strip sheet by means of
blanking and stamping processes. In this paper, the blanking process
and tooling parameters are evaluated by means of a 2D plane-strain
finite element model in order to evaluate the punch load and quality
of the sheared edges of Inconel 718 strips used for nuclear spacer
grids. A 3D finite element model is also proposed to predict the
tooling loads resulting from the stamping process of a preformed
Inconel 718 strip and to analyse the residual stress effects upon the
spring and dimple design geometries of a nuclear spacer grid.
Abstract: This paper presents the local mesh co-occurrence
patterns (LMCoP) using HSV color space for image retrieval system.
HSV color space is used in this method to utilize color, intensity and
brightness of images. Local mesh patterns are applied to define the
local information of image and gray level co-occurrence is used to
obtain the co-occurrence of LMeP pixels. Local mesh co-occurrence
pattern extracts the local directional information from local mesh
pattern and converts it into a well-mannered feature vector using gray
level co-occurrence matrix. The proposed method is tested on three
different databases called MIT VisTex, Corel, and STex. Also, this
algorithm is compared with existing methods, and results in terms of
precision and recall are shown in this paper.
Abstract: Experiential marketing is one of the marketing
approaches that offer an exceptional framework to integrate elements
of experience and entertainment in a product or service. Experiential
marketing is defined as a memorable experience that goes deeply into
the customer’s mind. Besides that, customer satisfaction is defined as
an emotional response to the experiences provided by and associated
with particular products or services purchased. Thus, experiential
marketing activities can affect the level of customer satisfaction and
loyalty. In this context, the research aims to explore the relationship
among experiential marketing, customer satisfaction and customer
loyalty among the cosmetic products customers in Konya. The partial
least squares (PLS) method is used to analyze the survey data.
Findings of the present study revealed that experiential marketing has
been a significant predictor of customer satisfaction and customer
loyalty, and also experiential marketing has a significantly positive
effect on customer satisfaction and customer loyalty.
Abstract: Sustainability is a very important and heavily
discussed subject, expanding through tourism as well. The study
proposition was to collect data and present it to the competent bodies
so they can mold their public policies to improve the conditions of
the site. It was hypothesized that the lack of data is currently
affecting the quality of life and the sustainable development of the
site and the tourism. The research was held in Mateiros, a city in the
state of Tocantins (TO)/Brasil near Palmas, its capital city. Because
of the concentration of tourists during the high season and several
tourist attractions being around, the research took place in Mateiros.
The methodological procedure had a script of theoretical construction
and investigation of the deductive scientific method parameters
through a case study in the Jalapão/TO/Brazil region, using it as a
tool for a questionnaire given to the competent bodies in an interview
system with the UN sustainability indexes as a base. In the three
sustainable development scope: environmental, social and economic,
the results indicated that the data presented by the interviewed were
scarce or nonexistent. It shows that more research is necessary,
providing the tools for the ones responsible to propose action plans to
improve the site, strengthening the tourism and making it even more
sustainable.
Abstract: Several embryonic cellular mechanism including cell
cycle, growth and apoptosis are regulated by phosphatidylinositol-3-
kinase (PI3K)/Akt signaling pathway. The goal of present study is to
determine the effects of annatto (Bixa orellana)-derived δ-tocotrienol
(δ-TCT) on the regulations of PI3K/Akt genes in murine morula.
Twenty four 6-8 week old (23-25g) female balb/c mice were
randomly divided into four groups (G1-G4; n=6). Those groups were
subjected to the following treatments for 7 consecutive days: G1
(control) received tocopherol stripped corn oil, G2 was given 60
mg/kg/day of δ-TCT mixture (contains 90% delta & 10% gamma
isomers), G3 was given 60 mg/kg/day of pure δ-TCT (>98% purity)
and G4 received 60 mg/kg/day α-TOC. On Day 8, females were
superovulated with 5 IU Pregnant Mare’s Serum Gonadotropin
(PMSG) for 48 hours followed with 5 IU human Chorionic
Gonadotropin (hCG) before mated with males at the ratio of 1:1.
Females were sacrificed by cervical dislocation for embryo collection
48 hours post-coitum. About fifty morulas from each group were
used in the gene expression analyses using Affymetrix QuantiGene
Plex 2.0 Assay. Present data showed a significant increase (p
Abstract: Multiple User Interference (MUI) considers the
primary problem in Optical Code-Division Multiple Access
(OCDMA), which resulting from the overlapping among the users. In
this article we aim to mitigate this problem by studying an
interference cancellation scheme called successive interference
cancellation (SIC) scheme. This scheme will be tested on two
different detection schemes, spectral amplitude coding (SAC) and
direct detection systems (DS), using partial modified prime (PMP) as
the signature codes. It was found that SIC scheme based on both SAC
and DS methods had a potential to suppress the intensity noise, that is
to say it can mitigate MUI noise. Furthermore, SIC/DS scheme
showed much lower bit error rate (BER) performance relative to
SIC/SAC scheme for different magnitude of effective power. Hence,
many more users can be supported by SIC/DS receiver system.
Abstract: The purpose of the paper is to address the strategic
risk issues surrounding Hindi film distribution in Mumbai for a film
distributor, who acts as an entrepreneur when launching a product
(movie) in the market (film territory).The paper undertakes a
fundamental review of films and risk in the Hindi film industry and
applies Grounded Theory technique to understand the complex
phenomena of risk taking behavior of the film distributors (both
independent and studios) in Mumbai. Rich in-depth interviews with
distributors are coded to develop core categories through constant
comparison leading to conceptualization of the phenomena of
interest. This paper is a first-of-its-kind-attempt to understand risk
behavior of a distributor, which is akin to entrepreneurial risk
behavior under conditions of uncertainty.
Abstract: In this paper, we present a four-step ortho-rectification
procedure for real-time geo-referencing of video data from a low-cost
UAV equipped with a multi-sensor system. The basic procedures for
the real-time ortho-rectification are: (1) decompilation of the video
stream into individual frames; (2) establishing the interior camera
orientation parameters; (3) determining the relative orientation
parameters for each video frame with respect to each other; (4)
finding the absolute orientation parameters, using a self-calibration
bundle and adjustment with the aid of a mathematical model. Each
ortho-rectified video frame is then mosaicked together to produce a
mosaic image of the test area, which is then merged with a well
referenced existing digital map for the purpose of geo-referencing
and aerial surveillance. A test field located in Abuja, Nigeria was
used to evaluate our method. Video and telemetry data were collected
for about fifteen minutes, and they were processed using the four-step
ortho-rectification procedure. The results demonstrated that the
geometric measurement of the control field from ortho-images is
more accurate when compared with those from original perspective
images when used to pin point the exact location of targets on the
video imagery acquired by the UAV. The 2-D planimetric accuracy
when compared with the 6 control points measured by a GPS receiver
is between 3 to 5 metres.
Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.
Abstract: In this paper air quality conditions in Makkah and
Leeds are compared. These two cities have totally different climatic
conditions. Makkah climate is characterised as hot and dry (arid)
whereas that of Leeds is characterised as cold and wet (temperate).
This study uses air quality data from 2012 collected in Makkah,
Saudi Arabia and Leeds, UK. The concentrations of all pollutants,
except NO are higher in Makkah. Most notable, the concentrations of
PM10 are much higher in Makkah than in Leeds. This is probably due
to the arid nature of climatic conditions in Makkah and not solely due
to anthropogenic emission sources, otherwise like PM10 some of the
other pollutants, such as CO, NO, and SO2 would have shown much
greater difference between Leeds and Makkah. Correlation analysis is
performed between different pollutants at the same site and the same
pollutants at different sites. In Leeds the correlation between PM10
and other pollutants is significantly stronger than in Makkah. Weaker
correlation in Makkah is probably due to the fact that in Makkah
most of the gaseous pollutants are emitted by combustion processes,
whereas most of the PM10 is generated by other sources, such as
windblown dust, re-suspension, and construction activities. This is in
contrast to Leeds where all pollutants including PM10 are
predominantly emitted by combustions, such as road traffic.
Furthermore, in Leeds frequent rains wash out most of the
atmospheric particulate matter and suppress re-suspension of dust.
Temporal trends of various pollutants are compared and discussed.
This study emphasises the role of climatic conditions in managing air
quality, and hence the need for region-specific controlling strategies
according to the local climatic and meteorological conditions.
Abstract: The study is in application and analysis of two tourism
management tools that can contribute to making public managers
decision: the Barometer of Tourism Sustainability (BTS) and the
Ecological Footprint (EF). The results have shown that BTS allows
you to have an integrated view of the tourism system, awakening to
the need for planning of appropriate actions so that it can achieve the
positive scale proposed (potentially sustainable). Already the
methodology of ecological tourism footprint is an important tool to
measure potential impacts generated by tourism to tourist reality.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: Due to the resultant leachate from waste
decomposition in landfills has polluter potential hundred times
greater than domestic sewage, this is considered a problem related to
the depreciation of environment requiring pre-disposal treatment.In
seeking to improve this situation, this project proposes the treatment
of landfill leachate using natural fibers intercropped with advanced
oxidation processes. The selected natural fibers were palm, coconut
and banana fiber.These materials give sustainability to the project
because, besides having adsorbent capacity, are often part of waste
discarded. The study was conducted in laboratory scale.In trials, the
effluents were characterized as Chemical Oxygen Demand (COD),
Turbidity and Color. The results indicate that is technically
promising since that there were extremely oxidative conditions, the
use of certain natural fibers in the reduction of pollutants in leachate
have been obtained results of COD removals between 67.9% and
90.9%, Turbidity between 88.0% and 99.7% and Color between
67.4% and 90.4%.The expectation generated is to continue evaluating
the association of efficiency of other natural fibers with other landfill
leachate treatment processes.
Abstract: In this study, the feasibility of incorporating ceramic
waste from bricks (perforated brick and double hollow brick) and
extruded polystyrene (XPS) waste, is analysed.
Results show that it is possible to incorporate up to 25% of
ceramic waste and 4% of XPS waste over the weight of gypsum in a
gypsum matrix. Furthermore, with the addition of ceramic waste an
8% of surface hardness increase and a 25% of capillary water
absorption reduction can be obtained. On the other hand, with the
addition of XPS, a 26% reduction of density and a 37% improvement
of thermal conductivity can be obtained.
The obtained results are favorable to use these materials in order to
produce prefabricated gypsum and also as material for interior
cladding walls.