Abstract: This paper proposes a low power SRAM based on
five transistor SRAM cell. Proposed SRAM uses novel word-line
decoding such that, during read/write operation, only selected cell
connected to bit-line whereas, in conventional SRAM (CV-SRAM),
all cells in selected row connected to their bit-lines, which in turn
develops differential voltages across all bit-lines, and this makes
energy consumption on unselected bit-lines. In proposed SRAM
memory array divided into two halves and this causes data-line
capacitance to reduce. Also proposed SRAM uses one bit-line and
thus has lower bit-line leakage compared to CV-SRAM.
Furthermore, the proposed SRAM incurs no area overhead, and has
comparable read/write performance versus the CV-SRAM.
Simulation results in standard 0.25μm CMOS technology shows in
worst case proposed SRAM has 80% smaller dynamic energy
consumption in each cycle compared to CV-SRAM. Besides, energy
consumption in each cycle of proposed SRAM and CV-SRAM
investigated analytically, the results of which are in good agreement
with the simulation results.
Abstract: Macrobenthos distribution along the coastal waters of
Penang National Park was studid to estimate the effect of different
environmental parameters at three stations, during six sampling
months, from June 2010 to April 2011. The aim of this survey was to
investigate different environment stress over soft bottom polychaete
community along Teluk Ketapang and Pantai Acheh (Penang
National Park) over a year period. Variations in the polychaete
community were evaluated using univariate and multivariate
methods. A total of 604 individuals were examined which was
grouped into 23 families. Family Nereidae was the most abundant
(22.68%), followed by Spionidae (22.02%), Hesionidae (12.58%),
Nephtylidae (9.27%) and Orbiniidae (8.61%). It is noticeable that
good results can only be obtained on the basis of good taxonomic
resolution. The maximum Shannon-Wiener diversity (H'=2.16) was
recorded at distance 200m and 1200m (August 2010) in Teluk
Ketapang and lowest value of diversity was found at distance 1200m
(December 2010) in Teluk Ketapang.
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: A number of routing algorithms based on learning
automata technique have been proposed for communication
networks. How ever, there has been little work on the effects of
variation of graph scarcity on the performance of these algorithms. In
this paper, a comprehensive study is launched to investigate the
performance of LASPA, the first learning automata based solution to
the dynamic shortest path routing, across different graph structures
with varying scarcities. The sensitivity of three main performance
parameters of the algorithm, being average number of processed
nodes, scanned edges and average time per update, to variation in
graph scarcity is reported. Simulation results indicate that the LASPA
algorithm can adapt well to the scarcity variation in graph structure
and gives much better outputs than the existing dynamic and fixed
algorithms in terms of performance criteria.
Abstract: In this paper we present a general formalism for the
establishment of the family of selective regressor affine projection
algorithms (SR-APA). The SR-APA, the SR regularized APA (SR-RAPA),
the SR partial rank algorithm (SR-PRA), the SR binormalized
data reusing least mean squares (SR-BNDR-LMS), and the SR normalized
LMS with orthogonal correction factors (SR-NLMS-OCF)
algorithms are established by this general formalism. We demonstrate
the performance of the presented algorithms through simulations in
acoustic echo cancellation scenario.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: The aim of current study was to investigate the
changes in the quality parameters of Holstein bull semen during the
heat stress and the effect of feeding a source of omega-3 fatty acids
in this period. Samples were obtained from 19 Holstein bulls during
the expected time of heat stress in Iran (June to September 2009).
Control group (n=10) were fed a standard concentrate feed while
treatment group (n=9) had this feed top dressed with 100 g of an
omega-3 enriched nutriceutical. Semen quality was assessed on
ejaculates collected after 1, 5, 9 and 12 weeks of supplementation.
Computer-assisted assessment of sperm motility, viability (eosinnigrosin)
and hypo-osmotic swelling test (HOST) were conducted.
Heat stress affected sperm quality parameters by week 5 and 9
(p
Abstract: In this paper, we consider the effect of the initial
sample size on the performance of a sequential approach that used
in selecting a good enough simulated system, when the number
of alternatives is very large. We implement a sequential approach
on M=M=1 queuing system under some parameter settings, with a
different choice of the initial sample sizes to explore the impacts on
the performance of this approach. The results show that the choice
of the initial sample size does affect the performance of our selection
approach.
Abstract: Role of acoustic driving pressure on the
translational-radial dynamics of a moving single bubble
sonoluminescence (m-SBSL) has been numerically
investigated. The results indicate that increase in the
amplitude of the driving pressure leads to increase in the
bubble peak temperature. The length and the shape of the
trajectory of the bubble depends on the acoustic pressure and
because of the spatially dependence of the radial dynamics of
the moving bubble, its peak temperature varies during the
acoustical pulses. The results are in good agreement with the
experimental reports on m-SBSL.
Abstract: The present paper considers the steady free convection
boundary layer flow of a viscoelastic fluid on solid sphere with
Newtonian heating. The boundary layer equations are an order higher
than those for the Newtonian (viscous) fluid and the adherence
boundary conditions are insufficient to determine the solution of
these equations completely. Thus, the augmentation an extra
boundary condition is needed to perform the numerical
computational. The governing boundary layer equations are first
transformed into non-dimensional form by using special
dimensionless group and then solved by using an implicit finite
difference scheme. The results are displayed graphically to illustrate
the influence of viscoelastic K and Prandtl Number Pr parameters on
skin friction, heat transfer, velocity profiles and temperature profiles.
Present results are compared with the published papers and are found
to concur very well.
Abstract: The increasing importance of data stream arising in a
wide range of advanced applications has led to the extensive study of
mining frequent patterns. Mining data streams poses many new
challenges amongst which are the one-scan nature, the unbounded
memory requirement and the high arrival rate of data streams. In this
paper, we propose a new approach for mining itemsets on data
stream. Our approach SFIDS has been developed based on FIDS
algorithm. The main attempts were to keep some advantages of the
previous approach and resolve some of its drawbacks, and
consequently to improve run time and memory consumption. Our
approach has the following advantages: using a data structure similar
to lattice for keeping frequent itemsets, separating regions from each
other with deleting common nodes that results in a decrease in search
space, memory consumption and run time; and Finally, considering
CPU constraint, with increasing arrival rate of data that result in
overloading system, SFIDS automatically detect this situation and
discard some of unprocessing data. We guarantee that error of results
is bounded to user pre-specified threshold, based on a probability
technique. Final results show that SFIDS algorithm could attain
about 50% run time improvement than FIDS approach.
Abstract: This paper presents kinematic and dynamic analysis of a novel 8-DOF hybrid robot manipulator. The hybrid robot manipulator under consideration consists of a parallel robot which
is followed by a serial mechanism. The parallel mechanism has three translational DOF, and the serial mechanism has five DOF so that the overall degree of freedom is eight. The introduced
manipulator has a wide workspace and a high capability to reduce
the actuating energy. The inverse and forward kinematic solutions are described in closed form. The theoretical results are verified by
a numerical example. Inverse dynamic analysis of the robot is presented by utilizing the Iterative Newton-Euler and Lagrange dynamic formulation methods. Finally, for performing a multi-step
arc welding process, results have indicated that the introduced manipulator is highly capable of reducing the actuating energy.
Abstract: In order to evaluation the effects of soil organic
matter and biofertilizer on chickpea quality and biological
nitrogen fixation, field experiments were carried out in 2007
and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on
grain yield and yield component, minerals, organic compounds
and cooking time of chickpea. Experimental units were
arranged in split-split plots based on randomized complete
blocks with three replications. Main plots consisted of (G1):
establishing a mixed vegetation of Vicia panunica and
Hordeum vulgare and (G2): control, as green manure levels.
Also, five strategies for obtaining the base fertilizer
requirement including (N1): 20 t.ha-1 farmyard manure; (N2):
10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5):
10 t.ha-1 farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1
triple super phosphate were considered in sub plots.
Furthermoree four levels of biofertilizers consisted of (B1):
Bacillus lentus + Pseudomonas putida; (B2): Trichoderma
harzianum; (B3): Bacillus lentus + Pseudomonas putida +
Trichoderma harzianum; and (B4): control (without
biofertilizers) were arranged in sub-sub plots. Results showed
that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield
were obtained in G1×N5 interaction. Comparison of all 2-way
and 3-way interactions showed that G1N5B3 was determined
as the superior treatment. Significant increasing of N, P2O5,
K2O, Fe and Mg content in leaves and grains emphasized on
superiority of mentioned treatment because each one of these
nutrients has an approved role in chlorophyll synthesis and
photosynthesis abilities of the crops. The combined application
of compost, farmyard manure and chemical phosphorus (N5)
in addition to having the highest yield, had the best grain
quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.
Abstract: Selection of the best possible set of suppliers has a
significant impact on the overall profitability and success of any
business. For this reason, it is usually necessary to optimize all
business processes and to make use of cost-effective alternatives for
additional savings. This paper proposes a new efficient context-aware
supplier selection model that takes into account possible changes of
the environment while significantly reducing selection costs. The
proposed model is based on data clustering techniques while
inspiring certain principles of online algorithms for an optimally
selection of suppliers. Unlike common selection models which re-run
the selection algorithm from the scratch-line for any decision-making
sub-period on the whole environment, our model considers the
changes only and superimposes it to the previously defined best set
of suppliers to obtain a new best set of suppliers. Therefore, any recomputation
of unchanged elements of the environment is avoided
and selection costs are consequently reduced significantly. A
numerical evaluation confirms applicability of this model and proves
that it is a more optimal solution compared with common static
selection models in this field.
Abstract: Evaluation and survey of curriculum quality as one of the most important components of universities system is necessary for different levels in higher education. The main purpose of this study was to survey of the curriculum quality of Actuarial science field. Case: University of SHahid Beheshti and Higher education institute of Eco insurance (according to viewpoint of students, alumni, employers and faculty members). Descriptive statistics (mean, tables, percentage, and frequency distribution) and inferential statistics (CHI SQUARE) were used to analyze the data. Six criteria considered for the Quality of curriculum: objectives, content, teaching and learning methods, space and facilities, Time, assessment of learning. Content, teaching and learning methods, space and facilities, assessment of learning criteria were relatively desirable level, objectives and time criterions were desirable level. The quality of curriculum of Actuarial Science field was relatively desirable level.
Abstract: Pretreatment of oil palm empty fruit bunch (OPEFB) with N-Methylmorpholine-N-oxide (NMMO) to enhance biogas production was investigated. The pretreatments were performed at 90 and 120ºC for 1, 3, and 5 h using three different concentrations of NMMO of 73%, 79%, and 85%. The pretreated OPEFB was subsequently anaerobically digested to produce biogas. After pretreatment, there were no significant changes of the main composition of OPEFB and the maximum total solid recovery was 92%. The amorphous phase was increased up to 78% at pretreatment condition using 85% NMMO solution for 3 h at 120oC. In general, higher concentration of NMMO and higher temperature resulted in increased amorphous form and higher biogas production. The best results of biogas production reached enhancement of methane yield of 148% compared to the untreated OPEFB and increased in digestion of 94% compared to starch as reference.
Abstract: By means of the extended homoclinic test approach (shortly EHTA) with the aid of a symbolic computation system such as Maple, some complexiton type solutions for the (3+1)-dimensional Jimbo-Miwa equation are presented.
Abstract: The interaction of the blade tip with the casing
boundary layer and the leakage flow may lead to a kind of cavitation
namely tip vortex cavitation. In this study, the onset of tip vortex
cavitation was experimentally investigated in an axial flow pump.
For a constant speed and a fixed angle of attack and by changing the
flow rate, the pump head, input power, output power and efficiency
were calculated and the pump characteristic curves were obtained.
The cavitation phenomenon was observed with a camera and a
stroboscope. Finally, the critical flow region, which tip vortex
cavitation might have occurred, was identified. The results show that
just by adjusting the flow rate, out of the specified region, the
possibility of occurring tip vortex cavitation, decreases to a great
extent.
Abstract: In this paper an effective approach for segmenting
human skin regions in images taken at different environment is
proposed. The proposed method uses a color distance map that is
flexible enough to reliably detect the skin regions even if the
illumination conditions of the image vary. Local image conditions is
also focused, which help the technique to adaptively detect differently
illuminated skin regions of an image. Moreover, usage of local
information also helps the skin detection process to get rid of picking
up much noisy pixels.