Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: In this study a two dimensional axisymmetric, steady state and incompressible laminar flow in a rotating single disk is numerically investigated. The finite volume method is used for solving the momentum equations. The numerical model and results
are validated by comparing it to previously reported experimental data for velocities, angles and moment coefficients. It is
demonstrated that increasing the axial distance increases the value of axial velocity and vice versa for tangential and total velocities. However, the maximum value of nondimensional radial velocity
occurs near the disk wall. It is also found that with increase rotational Reynolds number, moment coefficient decreases.
Abstract: The presence of harmonic in power system is a major
concerned to power engineers for many years. With the increasing
usage of nonlinear loads in power systems, the harmonic pollution
becomes more serious. One of the widely used computation
algorithm for harmonic analysis is fast Fourier transform (FFT). In
this paper, a harmonic analyzer using FFT was implemented on
TMS320C6713 DSK. The supply voltage of 240 V 59 Hz is stepped
down to 5V using a voltage divider in order to match the power
rating of the DSK input. The output from the DSK was displayed on
oscilloscope and Code Composer Studio™ software. This work has
demonstrated the possibility of analyzing the 240V power supply
harmonic content using the DSK board.
Abstract: In composting process, N high-organic wastes loss the
great part of its nitrogen as ammonia; therefore, using compost
amendments can promote the quality of compost due to the decrease
in ammonia volatilization. With regard to the effect of pH on
composting, microorganisms- activity and ammonia volatilization,
sulfuric acid and alkaline wastewater of paper mill (as liming agent
with Ca and Mg ions) were used as compost amendments. Study
results indicated that these amendments are suitable for reclamation
of compost quality properties. These held nitrogen in compost caused
to reduce C/N ratio. Both amendments had a significant effect on
total nitrogen, but it should be used sulfuric acid in fewer amounts
(20 ml/kg fresh organic wastes); and the more amounts of acid is not
proposed.
Abstract: In this paper we consider the issue of distributed adaptive estimation over sensor networks. To deal with more realistic scenario, different variance for observation noise is assumed for sensors in the network. To solve the problem of different variance of observation noise, the proposed method is divided into two phases: I) Estimating each sensor-s observation noise variance and II) using the estimated variances to obtain the desired parameter. Our proposed algorithm is based on a diffusion least mean square (LMS) implementation with linear combiner model. In the proposed algorithm, the step-size parameter the coefficients of linear combiner are adjusted according to estimated observation noise variances. As the simulation results show, the proposed algorithm considerably improves the diffusion LMS algorithm given in literature.
Abstract: The dramatic increasing of sea-freight container
transportations and the developing trends for using containers in the
multimodal handling systems through the sea, rail, road and land in
nowadays market cause general managers of container terminals to
face challenges such as increasing demand, competitive situation,
new investments and expansion of new activities and need to use new
methods to fulfil effective operations both along quayside and within
the yard. Among these issues, minimizing the turnaround time of
vessels is considered to be the first aim of every container port
system. Regarding the complex structure of container ports, this
paper presents a simulation model that calculates the number of
trucks needed in the Iranian Shahid Rajaee Container Port for
handling containers between the berth and the yard. In this research,
some important criteria such as vessel turnaround time, gantry crane
utilization and truck utilization have been considered. By analyzing
the results of the model, it has been shown that increasing the number
of trucks to 66 units has a significant effect on the performance
indices of the port and can increase the capacity of loading and
unloading up to 10.8%.
Abstract: In this paper, we propose an energy efficient cluster
based communication protocol for wireless sensor network. Our
protocol considers both the residual energy of sensor nodes and the
distance of each node from the BS when selecting cluster-head. This
protocol can successfully prolong the network-s lifetime by 1)
reducing the total energy dissipation on the network and 2) evenly
distributing energy consumption over all sensor nodes. In this
protocol, the nodes with more energy and less distance from the BS
are probable to be selected as cluster-head. Simulation results with
MATLAB show that proposed protocol could increase the lifetime of
network more than 94% for first node die (FND), and more than 6%
for the half of the nodes alive (HNA) factor as compared with
conventional protocols.
Abstract: Mathematical, graphical and intuitive models are often
constructed in the development process of computational systems.
The Unified Modeling Language (UML) is one of the most popular
modeling languages used by practicing software engineers. This
paper critically examines UML models and suggests an augmented
use case view with the addition of new constructs for modeling
software. It also shows how a use case diagram can be enhanced. The
improved modeling constructs are presented with examples for
clarifying important design and implementation issues.
Abstract: Nowadays, engineering ceramics have significant
applications in different industries such as; automotive, aerospace,
electrical, electronics and even martial industries due to their
attractive physical and mechanical properties like very high hardness
and strength at elevated temperatures, chemical stability, low friction
and high wear resistance. However, these interesting properties plus
low heat conductivity make their machining processes too hard,
costly and time consuming. Many attempts have been made in order
to make the grinding process of engineering ceramics easier and
many scientists have tried to find proper techniques to economize
ceramics' machining processes. This paper proposes a new diamond
plunge grinding technique using ultrasonic vibration for grinding
Alumina ceramic (Al2O3). For this purpose, a set of laboratory
equipments have been designed and simulated using Finite Element
Method (FEM) and constructed in order to be used in various
measurements. The results obtained have been compared with the
conventional plunge grinding process without ultrasonic vibration
and indicated that the surface roughness and fracture strength
improved and the grinding forces decreased.
Abstract: In the present study, a heterogeneous and
homogeneous gas flow dispersion model for simulation and
optimisation of a large-scale catalytic slurry reactor for the direct
synthesis of dimethyl ether (DME) from syngas and CO2, using a
churn-turbulent regime was developed. In the heterogeneous gas flow
model the gas phase was distributed into two bubble phases: small
and large, however in the homogeneous one, the gas phase was
distributed into only one large bubble phase. The results indicated
that the heterogeneous gas flow model was in more agreement with
experimental pilot plant data than the homogeneous one.
Abstract: In this paper back-propagation artificial neural
network (BPANN) with Levenberg–Marquardt algorithm is
employed to predict the limiting drawing ratio (LDR) of the deep
drawing process. To prepare a training set for BPANN, some finite
element simulations were carried out. die and punch radius, die arc
radius, friction coefficient, thickness, yield strength of sheet and
strain hardening exponent were used as the input data and the LDR
as the specified output used in the training of neural network. As a
result of the specified parameters, the program will be able to
estimate the LDR for any new given condition. Comparing FEM and
BPANN results, an acceptable correlation was found.
Abstract: Prime Factorization based on Quantum approach in
two phases has been performed. The first phase has been achieved at
Quantum computer and the second phase has been achieved at the
classic computer (Post Processing). At the second phase the goal is to
estimate the period r of equation xrN ≡ 1 and to find the prime factors
of the composite integer N in classic computer. In this paper we
present a method based on Randomized Approach for estimation the
period r with a satisfactory probability and the composite integer N
will be factorized therefore with the Randomized Approach even the
gesture of the period is not exactly the real period at least we can find
one of the prime factors of composite N. Finally we present some
important points for designing an Emulator for Quantum Computer
Simulation.
Abstract: Australian government agencies have a natural desire
to provide migrants a wide range of opportunities. Consequently,
government online services should be equally available to migrants
with a non-English speaking background (NESB). Despite the
commendable efforts of governments and local agencies in Australia
to provide such services, in reality, many NESB communities are not
taking advantage of these services. This article–based on an
extensive case study regarding the use of online government services
by the Arabic NESB community in Australia–reports on the
possible reasons for this issue, as well as suggestions for
improvement. The conclusion is that Australia should implement
ICT-based or e-government policies, programmes, and services that
more accurately reflect migrant cultures and languages so that
migrant integration can be more fully accomplished. Specifically, this
article presents an NESB Model that adopts the value of usercentricity
or a more individual-focused approach to government
online services in Australia.
Abstract: One of the main processes of supply chain
management is supplier selection process which its accurate
implementation can dramatically increase company competitiveness.
In presented article model developed based on the features of
second tiers suppliers and four scenarios are predicted in order to
help the decision maker (DM) in making up his/her mind. In addition
two tiers of suppliers have been considered as a chain of suppliers.
Then the proposed approach is solved by a method combined of
concepts of fuzzy set theory (FST) and linear programming (LP)
which has been nourished by real data extracted from an engineering
design and supplying parts company. At the end results reveal the
high importance of considering second tier suppliers features as
criteria for selecting the best supplier.
Abstract: In this paper, based on the coupled-mode and carrier rate equations, derivation of a dynamic model and numerically analysis of a MQW chirped DFB-SOA all-optical flip-flop is done precisely. We have analyzed the effects of strains of QW and MQW and cross phase modulation (XPM) on the dynamic response, and rise and fall times of the DFB-SOA all optical flip flop. We have shown that strained MQW active region in under an optimized condition into a DFB-SOA with chirped grating can improve the switching ON speed limitation in such a of the device, significantly while the fall time is increased. The values of the rise times for such an all optical flip-flop, are obtained in an optimized condition, areas tr=255ps.
Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.
Abstract: In this paper we present high performance
dynamically allocated multi-queue (DAMQ) buffer schemes for fault
tolerance systems on chip applications that require an interconnection
network. Two virtual channels shared the same buffer space. Fault
tolerant mechanisms for interconnection networks are becoming a
critical design issue for large massively parallel computers. It is also
important to high performance SoCs as the system complexity keeps
increasing rapidly. On the message switching layer, we make
improvement to boost system performance when there are faults
involved in the components communication. The proposed scheme is
when a node or a physical channel is deemed as faulty, the previous
hop node will terminate the buffer occupancy of messages destined
to the failed link. The buffer usage decisions are made at switching
layer without interactions with higher abstract layer, thus buffer
space will be released to messages destined to other healthy nodes
quickly. Therefore, the buffer space will be efficiently used in case
fault occurs at some nodes.
Abstract: Low temperature (LT) is one of the most abiotic
stresses causing loss of yield in wheat (T. aestivum). Four major
genes in wheat (Triticum aestivum L.) with the dominant alleles
designated Vrn–A1,Vrn–B1,Vrn–D1 and Vrn4, are known to have
large effects on the vernalization response, but the effects on cold
hardiness are ambiguous. Poor cold tolerance has restricted winter
wheat production in regions of high winter stress [9]. It was known
that nearly all wheat chromosomes [5] or at least 10 chromosomes of
21 chromosome pairs are important in winter hardiness [15]. The
objective of present study was to clarify the role of each chromosome
in cold tolerance. With this purpose we used 20 isogenic lines of
wheat. In each one of these isogenic lines only a chromosome from
‘Bezostaya’ variety (a winter habit cultivar) was substituted to
‘Capple desprez’ variety. The plant materials were planted in
controlled conditions with 20º C and 16 h day length in moderately
cold areas of Iran at Karaj Agricultural Research Station in 2006-07
and the acclimation period was completed for about 4 weeks in a
cold room with 4º C. The cold hardiness of these isogenic lines was
measured by LT50 (the temperature in which 50% of the plants are
killed by freezing stress).The experimental design was completely
randomized block design (RCBD)with three replicates. The results
showed that chromosome 5A had a major effect on freezing
tolerance, and then chromosomes 1A and 4A had less effect on this
trait. Further studies are essential to understanding the importance of
each chromosome in controlling cold hardiness in wheat.
Abstract: In this paper, the bond strength of thermal spray
coatings in high speed shafts has been studied. The metallurgical and
mechanical studies has been made on the coated samples and shaft
using optical microscopy, scanning electron microscopy (SEM).
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.