Abstract: The influence of human activities produced by dams
along the river beds is minor, but the location of accumulation of
water directly influences the hydrological regime. The most
important effect of the influence of damming on the way water flows
decreases the frequency of floods. The water rate controls the water
flow of the dams. These natural reservoirs become dysfunctional and,
as a result, a new distribution of flow in the downstream sector,
where maximum flow is, brings about, in this case, higher values. In
addition to fishing, middle and lower courses of rivers located by
accumulation also have a role in mitigating flood waves, thus
providing flood protection. The Vaslui also ensures a good part of the
needs of the town water supply. The most important lake is Solesti,
close to the Vaslui River, opened in 1974. A hydrological regime of
accumulation is related to an anthropogenic and natural drainage
system. The design conditions and their manoeuvres drain or fill the
water courses.
Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: In this paper, we propose a novel time-frequency distribution (TFD) for the analysis of multi-component signals. In particular, we use synthetic as well as real-life speech signals to prove the superiority of the proposed TFD in comparison to some existing ones. In the comparison, we consider the cross-terms suppression and the high energy concentration of the signal around its instantaneous frequency (IF).
Abstract: Concrete performance is strongly affected by the
particle packing degree since it determines the distribution of the
cementitious component and the interaction of mineral particles. By
using packing theory designers will be able to select optimal
aggregate materials for preparing concrete with low cement content,
which is beneficial from the point of cost. Optimum particle packing
implies minimizing porosity and thereby reducing the amount of
cement paste needed to fill the voids between the aggregate particles,
taking also the rheology of the concrete into consideration. For
reaching good fluidity superplasticizers are required. The results from
pilot tests at Luleå University of Technology (LTU) show various
forms of the proposed theoretical models, and the empirical approach
taken in the study seems to provide a safer basis for developing new,
improved packing models.
Abstract: The state-of-the-art Bag of Words model in Content-
Based Image Retrieval has been used for years but the relevance
feedback strategies for this model are not fully investigated. Inspired
from text retrieval, the Bag of Words model has the ability to use the
wealth of knowledge and practices available in text retrieval. We
study and experiment the relevance feedback model in text retrieval
for adapting it to image retrieval. The experiments show that the
techniques from text retrieval give good results for image retrieval
and that further improvements is possible.
Abstract: Larval survey was carried out in 6 localities in the
urban areas (Putrajaya) and suburban areas (Kuala Selangor) from
January until December 2010. A total of 520 representative
households in 6 localities were selected. Breeding habitats were
sampled outdoors in the surroundings of housing areas. The study
indicated that the most predominant species found in both areas was
Aedes albopictus with the gardening utensil as a preferred breeding
microhabitat for Putrajaya, in contrast to the artificial containers for
Kuala Selangor. From a total of 1083 mosquito larvae species, 984
were Aedes albopictus larvae, 67 positive larvae of Aedes aegypti
and 32 of Culex larvae. Aedes Index and Container Index were
elevated in Putrajaya with 13% and 11% respectively which is higher
than the standard given by the Ministry of Health, Malaysia. This
results implicating dengue-sensitive skewed to the urban areas.
Breteau Index result also above the standard in both study locations.
Abstract: Recently, lots of researchers are attracted to retrieving
multimedia database by using some impression words and their values.
Ikezoe-s research is one of the representatives and uses eight pairs of
opposite impression words. We had modified its retrieval interface and
proposed '2D-RIB'. In '2D-RIB', after a retrieval person selects a
single basic music, the system visually shows some other music
around the basic one along relative position. He/she can select one of
them fitting to his/her intention, as a retrieval result. The purpose of
this paper is to improve his/her satisfaction level to the retrieval result
in 2D-RIB. One of our extensions is to define and introduce the
following two measures: 'melody goodness' and 'general acceptance'.
We implement them in different five combinations. According to an
evaluation experiment, both of these two measures can contribute to
the improvement. Another extension is three types of customization.
We have implemented them and clarified which customization is
effective.
Abstract: The present research was designed to investigate the
anti-microbial activity of aristolochic acid from the root of
Aristolochia bracteata. From the methanolic & ethyl extract extracts
of Aristolochia bracteata aristolochic acid I was isolated and
conformed through IR, NMR & MS. The percentage purity of
aristolochic acid I was determined by UV & HPLC method. Antibacterial
activity of extracts of Aristolochia bracteata and the
isolated compound was determined by disc diffusion method. The
results reveled that the isolated aristolochic acid from methanolic
extract was more pure than the compound from ethyl acetate extract.
The various extracts (500μg/disc) of Aristolochia bracteata showed
moderate antibacterial activity with the average zone of inhibition of
7-18 mm by disc diffusion method. Among the extracts, ethyl acetate
& methanol extracts were shown good anti-microbial activity and the
growth of E.coli (18 mm) was strongly inhibited. Microbial assay of
isolated compound (Aristolochic acid I) from ethyl acetate &
methanol extracts were shown good antimicrobial activity and the
zone of inhibition of both at higher concentration 50 μg/ml was
similar with the standard aristolochic acid. It may be concluded that
the isolated compound of aristolochic acid I has good anti-bacterial
activity.
Abstract: In this work study the location of interface in a stirred vessel with a Concave impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: The selection of parents and breeding strategies for
the successful maize hybrid production will be facilitated by
heterotic groupings of parental lines and determination of combining
abilities of them. Fourteen maize inbred lines, used in maize breeding
programs in Iran, were crossed in a diallel mating design. The 91 F1
hybrids and the 14 parental lines were studied during two years at
four locations of Iran for investigation of combining ability of
gentypes for grain yield and to determine heterotic patterns among
germplasm sources, using both, the Griffing-s method and the biplot
approach for diallel analysis. The graphical representation offered by
biplot analysis allowed a rapid and effective overview of general
combining ability (GCA) and specific combining ability (SCA)
effects of the inbred lines, their performance in crosses, as well as
grouping patterns of similar genotypes. GCA and SCA effects were
significant for grain yield (GY). Based on significant positive GCA
effects, the lines derived from LSC could be used as parent in crosses
to increase GY. The maximum best- parent heterosis values and
highest SCA effects resulted from crosses B73 × MO17 and A679 ×
MO17 for GY. The best heterotic patterns were LSC × RYD, which
would be potentially useful in maize breeding programs to obtain
high-yielding hybrids in the same climate of Iran.
Abstract: Images of human iris contain specular highlights due
to the reflective properties of the cornea. This corneal reflection
causes many errors not only in iris and pupil center estimation but
also to locate iris and pupil boundaries especially for methods that
use active contour. Each iris recognition system has four steps:
Segmentation, Normalization, Encoding and Matching. In order to
address the corneal reflection, a novel reflection removal method is
proposed in this paper. Comparative experiments of two existing
methods for reflection removal method are evaluated on CASIA iris
image databases V3. The experimental results reveal that the
proposed algorithm provides higher performance in reflection
removal.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: The aim of current study was to investigate the
changes in the quality parameters of Holstein bull semen during the
heat stress and the effect of feeding a source of omega-3 fatty acids
in this period. Samples were obtained from 19 Holstein bulls during
the expected time of heat stress in Iran (June to September 2009).
Control group (n=10) were fed a standard concentrate feed while
treatment group (n=9) had this feed top dressed with 100 g of an
omega-3 enriched nutriceutical. Semen quality was assessed on
ejaculates collected after 1, 5, 9 and 12 weeks of supplementation.
Computer-assisted assessment of sperm motility, viability (eosinnigrosin)
and hypo-osmotic swelling test (HOST) were conducted.
Heat stress affected sperm quality parameters by week 5 and 9
(p
Abstract: This paper proposes the concept of aerocapture with
aerodynamic-environment-adaptive variable geometry flexible
aeroshell that vehicle deploys. The flexible membrane is composed
of thin-layer film or textile as its aeroshell in order to solve some
problems obstructing realization of aerocapture technique.
Multi-objective optimization study is conducted to investigate
solutions and derive design guidelines. As a result, solutions which
can avoid aerodynamic heating and enlarge the corridor width up
to 10% are obtained successfully, so that the effectiveness of this
concept can be demonstrated. The deformation-use optimum
solution changes its drag coefficient from 1.6 to 1.1, along with the
change in dynamic pressure. Moreover, optimization results show
that deformation-use solution requires the membrane for which
upper temperature limit and strain limit are more than 700 K and
120%, respectively, and elasticity (Young-s modulus) is of order of
106 Pa.
Abstract: Bangladesh is a developing country with large
population. Demand of electrical energy is increasing day by day
because of increasing population and industrialization. But due to
limited resources, people here are suffering from power crisis
problem which is considered as a major obstacle to the economic
development. In most of the cases, it is extremely difficult to extend
high tension transmission lines to some of the places that are
separated from the mainland. Renewable energy is considered to be
the right choice for providing clean energy to these remote
settlements. This paper proposes a cost effective design of off-grid
wind-diesel hybrid power system using combined heat and power
(CHP) technology in a grid isolated island, Sandwip, Bangladesh.
Design and simulation of the wind-diesel hybrid power system is
performed considering different factors for the island Sandwip.
Detailed economic analysis and comparison with solar PV system
clearly reveals that wind-diesel hybrid power system can be a cost
effective solution for the isolated island like Sandwip.
Abstract: In this paper, we consider the effect of the initial
sample size on the performance of a sequential approach that used
in selecting a good enough simulated system, when the number
of alternatives is very large. We implement a sequential approach
on M=M=1 queuing system under some parameter settings, with a
different choice of the initial sample sizes to explore the impacts on
the performance of this approach. The results show that the choice
of the initial sample size does affect the performance of our selection
approach.
Abstract: Image Searching was always a problem specially when these images are not properly managed or these are distributed over different locations. Currently different techniques are used for image search. On one end, more features of the image are captured and stored to get better results. Storing and management of such features is itself a time consuming job. While on the other extreme if fewer features are stored the accuracy rate is not satisfactory. Same image stored with different visual properties can further reduce the rate of accuracy. In this paper we present a new concept of using polynomials of sorted histogram of the image. This approach need less overhead and can cope with the difference in visual features of image.
Abstract: A manufacturing inventory model with shortages with
carrying cost, shortage cost, setup cost and demand quantity as
imprecise numbers, instead of real numbers, namely interval number
is considered here. First, a brief survey of the existing works on
comparing and ranking any two interval numbers on the real line
is presented. A common algorithm for the optimum production
quantity (Economic lot-size) per cycle of a single product (so as
to minimize the total average cost) is developed which works well
on interval number optimization under consideration. Finally, the
designed algorithm is illustrated with numerical example.
Abstract: The past decade has witnessed a good opportunities
for city development schemes in UK. The government encouraged
restoration of city centers to comprise mixed use developments with
high density residential apartments. Investments in regeneration areas
were doing well according to the analyses of Property Databank
(IPD). However, more recent analysis by IPD has shown that since
2007, property in regeneration areas has been more vulnerable to the
market downturn than other types of investment property. The early
stages of a property market downturn may be felt most in
regeneration where funding, investor confidence and occupier
demand would dissipate because the sector was considered more
marginal or risky when development costs rise. Moreover, the Bank
of England survey shows that lenders have sequentially tightened the
availability of credit for commercial real estate since mid-2007. A
sharp reduction in the willingness of banks to lend on commercial
property was recorded. The credit crunch has already affected
commercial property but its impact has been particularly severe in
certain kinds of properties where residential developments are
extremely difficult, in particular city centre apartments and buy-to-let
markets. Commercial property – retail, industrial leisure and mixed
use were also pressed, in Birmingham; tens of mixed use plots were
built to replace old factories in the heart of the city. The purpose of
these developments was to enable young professionals to work and
live in same place. Thousands of people lost their jobs during the
recession, moreover lending was more difficult and the future of
many developments is unknown. The recession casts its shadow upon
the society due to cuts in public spending by government, Inflation,
rising tuition fees and high rise in unemployment generated anger and
hatred was spreading among youth causing vandalism and riots in
many cities. Recent riots targeted many mixed used development in
the UK where banks, shops, restaurants and big stores were robbed
and set into fire leaving residents with horror and shock. This paper
examines the impact of the recession and riots on mixed use
development in UK.