Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.
Abstract: The aim of this paper is to introduce and study a new concept of strong double χ2 (M,A, Δ) of fuzzy numbers and also some properties of the resulting sequence spaces of fuzzy numbers were examined.
Abstract: In this study, cometabolic biodegradation of
chloroform was experimented with mixed cultures in the presence of
various organic solvents like methanol, ethanol, isopropanol, acetone,
acetonitrile and toluene as these are predominant discharges in
pharmaceutical industries. Toluene and acetone showed higher
specific chloroform degradation rate when compared to other
compounds. Cometabolic degradation of chloroform was further
confirmed by observation of free chloride ions in the medium. An
extended Haldane model, incorporating the inhibition due to
chloroform and the competitive inhibition between primary
substrates, was developed to predict the biodegradation of primary
substrates, cometabolic degradation of chloroform and the biomass
growth. The proposed model is based on the use of biokinetic
parameters obtained from single substrate degradation studies. The
model was able to satisfactorily predict the experimental results of
ternary and quaternary mixtures. The proposed model can be used for
predicting the performance of bioreactors treating discharges from
pharmaceutical industries.
Abstract: Due to the fact that in the new century customers tend
to express globally increasing demands, networks of interconnected
businesses have been established in societies and the management of
such networks seems to be a major key through gaining competitive
advantages. Supply chain management encompasses such managerial
activities. Within a supply chain, a critical role is played by quality.
QFD is a widely-utilized tool which serves the purpose of not only
bringing quality to the ultimate provision of products or service
packages required by the end customer or the retailer, but it can also
initiate us into a satisfactory relationship with our initial customer;
that is the wholesaler. However, the wholesalers- cooperation is
considerably based on the capabilities that are heavily dependent on
their locations and existing circumstances. Therefore, it is undeniable
that for all companies each wholesaler possesses a specific
importance ratio which can heavily influence the figures calculated in
the House of Quality in QFD. Moreover, due to the competitiveness
of the marketplace today, it-s been widely recognized that
consumers- expression of demands has been highly volatile in
periods of production. Apparently, such instability and proneness to
change has been very tangibly noticed and taking it into account
during the analysis of HOQ is widely influential and doubtlessly
required. For a more reliable outcome in such matters, this article
demonstrates the application viability of Analytic Network Process
for considering the wholesalers- reputation and simultaneously
introduces a mortality coefficient for the reliability and stability of
the consumers- expressed demands in course of time. Following to
this, the paper provides further elaboration on the relevant
contributory factors and approaches through the calculation of such
coefficients. In the end, the article concludes that an empirical
application is needed to achieve broader validity.
Abstract: Due to the dynamic nature of the Cloud, continuous monitoring of QoS requirements is necessary to manage the Cloud computing environment. The process of QoS monitoring and SLA violation detection consists of: collecting low and high level information pertinent to the service, analyzing the collected information, and taking corrective actions when SLA violations are detected. In this paper, we detail the architecture and the implementation of the first step of this process. More specifically, we propose an event-based approach to obtain run time information of services developed as BPEL processes. By catching particular events (i.e., the low level information), our approach recognizes the run-time execution path of a monitored service and uses the BPEL execution patterns to compute QoS of the composite service (i.e., the high level information).
Abstract: Computer technology and the Internet have made a
breakthrough in the existence of data communication. This has
opened a whole new way of implementing steganography to ensure
secure data transfer. Steganography is the fine art of hiding the
information. Hiding the message in the carrier file enables the
deniability of the existence of any message at all. This paper designs
a stego machine to develop a steganographic application to hide data
containing text in a computer video file and to retrieve the hidden
information. This can be designed by embedding text file in a video
file in such away that the video does not loose its functionality using
Least Significant Bit (LSB) modification method. This method
applies imperceptible modifications. This proposed method strives
for high security to an eavesdropper-s inability to detect hidden
information.
Abstract: Sustainable development is a concept which was
originated in Burtland commission in 1978. Although this concept
was born with environmental aspects, it is penetrated in all areas
rapidly, turning into a dominate view of planning. Concentrating on
future generation issue, especially when talking about heritage has a
long story. Each approach with all of its characteristics illustrates
differences in planning, hence planning always reflects the dominate
idea of its age. This paper studies sustainable development in
planning for historical cities with the aim of finding ways to deal
with heritage in planning for historical cities in Iran. Through this, it
will be illustrated how challenges between sustainable concept and
heritage could be concluded in planning.
Consequently, the paper will emphasize on:
Sustainable development in city planning
Trends regarding heritage
Challenges due to planning for historical cities in Iran
For the first two issues, documentary method regarding the
sustainable development and heritage literature is considered. As the
next step focusing on Iranian historical cities require considering the
urban planning and management structure and identifying the main
challenges related to heritage, so analyzing challenges regarding
heritage is considered. As the result it would be illustrated that key
issue in such planning is active conservation to improve and use the
potential of heritage while it's continues conservation is guaranteed.
By emphasizing on the planning system in Iran it will be obvious that
some reforms are needed in this system and its way of relating with
heritage. The main weakness in planning for historical cities in Iran
is the lack of independent city management. Without this factor
achieving active conservation as the main factor of sustainable
development would not be possible.
Abstract: The area of Project Risk Management (PRM) has
been extensively researched, and the utilization of various tools and
techniques for managing risk in several industries has been
sufficiently reported. Formal and systematic PRM practices have
been made available for the construction industry. Based on such
body of knowledge, this paper tries to find out the global picture of
PRM practices and approaches with the help of a survey to look into
the usage of PRM techniques and diffusion of software tools, their
level of maturity, and their usefulness in the construction sector.
Results show that, despite existing techniques and tools, their usage is
limited: software tools are used only by a minority of respondents
and their cost is one of the largest hurdles in adoption. Finally, the
paper provides some important guidelines for future research
regarding quantitative risk analysis techniques and suggestions for
PRM software tools development and improvement.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: This paper describes the results of an extensive study
and comparison of popular hash functions SHA-1, SHA-256,
RIPEMD-160 and RIPEMD-320 with JERIM-320, a 320-bit hash
function. The compression functions of hash functions like SHA-1
and SHA-256 are designed using serial successive iteration whereas
those like RIPEMD-160 and RIPEMD-320 are designed using two
parallel lines of message processing. JERIM-320 uses four parallel
lines of message processing resulting in higher level of security than
other hash functions at comparable speed and memory requirement.
The performance evaluation of these methods has been done by using
practical implementation and also by using step computation
methods. JERIM-320 proves to be secure and ensures the integrity of
messages at a higher degree. The focus of this work is to establish
JERIM-320 as an alternative of the present day hash functions for the
fast growing internet applications.
Abstract: The present study focuses on methods allowing a convenient and quick calculation of the SIFs in order to predict the static adhesive strength of bonded joints. A new SIF calculation method is proposed, based on the stresses obtained from a FE model at a reference point located in the adhesive layer at equal distance of the free-edge and of the two interfaces. It is shown that, even limiting ourselves to the two main modes, i.e. the opening and the shearing modes, and using the values of the stresses resulting from a low detailed FE model, an efficient calculation of the peeling stress at adhesive-substrate corners can be obtained by this way. The proposed method is interesting in that it can be the basis of a prediction tool that will allow the designer to quickly evaluate the SIFs characterizing a particular application without developing a detailed analysis.
Abstract: Delivering streaming video over wireless is an
important component of many interactive multimedia applications
running on personal wireless handset devices. Such personal devices
have to be inexpensive, compact, and lightweight. But wireless
channels have a high channel bit error rate and limited bandwidth.
Delay variation of packets due to network congestion and the high bit
error rate greatly degrades the quality of video at the handheld
device. Therefore, mobile access to multimedia contents requires
video transcoding functionality at the edge of the mobile network for
interworking with heterogeneous networks and services. Therefore,
to guarantee quality of service (QoS) delivered to the mobile user, a
robust and efficient transcoding scheme should be deployed in
mobile multimedia transporting network. Hence, this paper
examines the challenges and limitations that the video transcoding
schemes in mobile multimedia transporting network face. Then
handheld resources, network conditions and content based mobile
and wireless video transcoding is proposed to provide high QoS
applications. Exceptional performance is demonstrated in the
experiment results. These experiments were designed to verify and
prove the robustness of the proposed approach. Extensive
experiments have been conducted, and the results of various video
clips with different bit rate and frame rate have been provided.
Abstract: A known iterative computational procedure is used for
internal normal ball loads calculation in statically loaded single-row,
angular-contact ball bearings, subjected to a known thrust load,
which is applied in the inner ring at the geometric bearing center line.
Numerical aspects of the iterative procedure are discussed.
Numerical examples results for a 218 angular-contact ball bearing
have been compared with those from the literature. Twenty figures
are presented showing the geometrical features, the behavior of the
convergence variables and the following parameters as functions of
the thrust load: normal ball loads, contact angle, distance between
curvature centers, and normal ball and axial deflections between the
raceways.
Abstract: Multimedia, as it stands now is perhaps the most
diverse and rich culture around the globe. One of the major needs of
Multimedia is to have a single system that enables people to
efficiently search through their multimedia catalogues. Many
Domain Specific Systems and architectures have been proposed but
up till now no generic and complete architecture is proposed. In this
paper, we have suggested a generic architecture for Multimedia
Database. The main strengths of our architecture besides being
generic are Semantic Libraries to reduce semantic gap, levels of
feature extraction for more specific and detailed feature extraction
according to classes defined by prior level, and merging of two types
of queries i.e. text and QBE (Query by Example) for more accurate
yet detailed results.
Abstract: The objective of this research was to determine the
potency of indigenous acid-aluminium tolerant Bradyrhizobium
japonicum as producer of indole acetic acid (IAA) and applied it as
nitrogen fixation on local soybeans viz Anjasmoro, Tanggamus
(yellow soybean seeds), and Detam (black soybean seed). Three
isolates of acid-aluminium tolerant Bradyrhizobium japonicum (BJ)
were used in this research, i.e. BJ 11 (wt), BJ 11 (19) - BJ 11(wt)
mutant, and USDA 110 as a reference isolate. All of isolates tested to
produce the IAA by using Salkowsky method. Effect of IAA
production by each of B. japonicum was tested on growth pouch and
greenhouse using three varieties of soybean. All isolates could grow
well and produce IAA on yeast mannitol broth (YMB) medium in
the presence of 0.5 mM L-tryptophan. BJ 11 (19) produced the
highest of IAA at 4 days incubation compared to BJ 11 (wt) and
USDA 110. All tested isolates of Bradyrhizobium japonicum have
showed effect on stimulating the formation of root nodules in
soybean varieties grown on Leonard bottle. The concentration of
IAA on root nodules of soybean symbiotic with B. japonicum was
significantly different with control, except on the treatment using
Tanggamus soybean.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: Existing proceeding-models for the development of mechatronic systems provide a largely parallel action in the detailed development. This parallel approach is to take place also largely independent of one another in the various disciplines involved. An approach for a new proceeding-model provides a further development of existing models to use for the development of Adaptronic Systems. This approach is based on an intermediate integration and an abstract modeling of the adaptronic system. Based on this system-model a simulation of the global system behavior, due to external and internal factors or Forces is developed. For the intermediate integration a special data management system is used. According to the presented approach this data management system has a number of functions that are not part of the "normal" PDM functionality. Therefore a concept for a new data management system for the development of Adaptive system is presented in this paper. This concept divides the functions into six layers. In the first layer a system model is created, which divides the adaptronic system based on its components and the various technical disciplines. Moreover, the parameters and properties of the system are modeled and linked together with the requirements and the system model. The modeled parameters and properties result in a network which is analyzed in the second layer. From this analysis necessary adjustments to individual components for specific manipulation of the system behavior can be determined. The third layer contains an automatic abstract simulation of the system behavior. This simulation is a precursor for network analysis and serves as a filter. By the network analysis and simulation changes to system components are examined and necessary adjustments to other components are calculated. The other layers of the concept treat the automatic calculation of system reliability, the "normal" PDM-functionality and the integration of discipline-specific data into the system model. A prototypical implementation of an appropriate data management with the addition of an automatic system development is being implemented using the data management system ENOVIA SmarTeam V5 and the simulation system MATLAB.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: The quantified residence time distribution (RTD)
provides a numerical characterization of mixing in a reactor, thus
allowing the process engineer to better understand mixing
performance of the reactor.This paper discusses computational
studies to investigate flow patterns in a two impinging streams
cyclone reactor(TISCR) . Flow in the reactor was modeled with
computational fluid dynamics (CFD). Utilizing the Eulerian-
Lagrangian approach, implemented in FLUENT (V6.3.22), particle
trajectories were obtained by solving the particle force balance
equations. From simulation results obtained at different Δts, the mean
residence time (tm) and the mean square deviation (σ2) were
calculated. a good agreement can be observed between predicted and
experimental data. Simulation results indicate that the behavior of
complex reactor systems can be predicted using the CFD technique
with minimum data requirement for validation.
Abstract: After a strong earthquake occurs, a secondary disaster due to strong aftershocks, flood, landslide or heavy snow can possible to occur and the secondary disaster due to resident-s action also can possible to happen. However, until now seldom researchers have paid attention at it. This paper focused on the Inhabitant-s action after the strong earthquake occurs when a terrible even becomes calm. An inappropriate behavior of people with disadvantaged climate after the worse earthquake can bring a tragedy to their life.