Abstract: The predictability of masonry arch bridges and their
behaviour is widely considered doubtful due to the lack of knowledge
about the conditions of a given masonry arch bridge. The assessment
methods for masonry arch bridges are MEXE, ARCHIE, RING and
Frame Analysis Method. The material properties of the masonry and
fill material are extremely difficult to determine accurately.
Consequently, it is necessary to examine the effect of load dispersal
angle through the fill material, the effect of variations in the stiffness
of the masonry, the tensile strength of the masonry mortar continuum
and the compressive strength of the masonry mortar continuum. It is
also important to understand the effect of fill material on load
dispersal angle to determine their influence on ratings. In this paper a
series of parametric studies, to examine the sensitivity of assessment
ratings to the various sets of input data required by the frame analysis
method, are carried out.
Abstract: Wheat has a bimodal starch granule population and the dependency of the rate of enzymatic hydrolysis on particle size has been investigated. Ungelatinised wheaten starch granules were separated into two populations by sedimentation and decantation. Particle size was analysed by laser diffraction and morphological characteristics were viewed using SEM. The sedimentation technique though lengthy, gave satisfactory separation of the granules. Samples (10μm and original) were digested with a-amylase using a dialysis model. Granules of 10μm (p10μm. Moreover, the digestion rate was dependent on particle size whereby smaller granules produced higher rate of release. The methodology and results reported here can be used as a basis for further evaluations designed to delay the release of glucose during the digestion of native starches.
Abstract: Plant growth is affected by the osmotic stress as well as toxicity of salt in leaves. In order to study of salt stress effects on stomatal conductance and growth rate and relationship between them as wells osmotic and Na+-specific effects on these traits, four bread wheat genotypes differing in salt tolerance were selected. Salinity was applied when the leaf 4 was fully expanded. Sodium (Na+) concentrations in flag leaf blade at 3 salinity levels (0, 100 and 200 mM NaCl) were measured. Salt-tolerant genotypes showed higher stomatal conductance and growth rate compared to salt-sensitive ones. After 10 and 20 days exposure to salt, stomatal conductance and relative growth rate were reduced, but the reduction was greater in sensitive genotypes. Growth rate was reduced severely in the first period (1-10 days) of salt commencements and it was due to osmotic effect of salt not Na+ toxicity. In the second period (11-20 days) after salt treatment growth reduced only when salt accumulated to toxic concentrations in the leaves. A positive relationship between stomatal conductance and relative growth rate showed that stomatal conductance can be a reliable indicator of growth rate, and finally can be considered as a sensitive indicator of the osmotic stress. It seems 20 days after salinity, the major effect of salt, especially at low to moderate salinity levels on growth properties was due to the osmotic effect of salt, not to Na+-specific effects within the plant.
Abstract: Formulation of biological profile is one of the modern roles of forensic anthropologist. The present study was conducted to estimate height using foot and shoeprint length of Malaysian population. The present work can be very useful information in the process of identification of individual in forensic cases based on shoeprint evidence. It can help to narrow down suspects and ease the police investigation. Besides, stature is important parameters in determining the partial identify of unidentified and mutilated bodies. Thus, this study can help the problem encountered in cases of mass disaster, massacre, explosions and assault cases. This is because it is very hard to identify parts of bodies in these cases where people are dismembered and become unrecognizable. Samples in this research were collected from 200 Malaysian adults (100 males and 100 females) with age ranging from 20 to 45 years old. In this research, shoeprint length were measured based on the print of the shoes made from the flat shoes. Other information like gender, foot length and height of subject were also recorded. The data was analyzed using IBM® SPSS Statistics 19 software. Results indicated that, foot length has a strong correlation with stature than shoeprint length for both sides of the feet. However, in the unknown, where the gender was undetermined have shown a better correlation in foot length and shoeprint length parameter compared to males and females analyzed separately. In addition, prediction equations are developed to estimate the stature using linear regression analysis of foot length and shoeprint length. However, foot lengths give better prediction than shoeprint length.
Abstract: In this research, natural canthaxanthin as one of the
most important carotenoids was extracted from Dietzia
natronolimnaea HS-1. The changes of canthaxanthin enriched in oilin-
water emulsions with vegetable oil (5 mg/ 100 mL), Arabic gum (5
mg/100 mL), and potassium sorbate (0.5 g/100 mL) was investigated.
The effects of different pH (3, 5 and 7), as well as, time treatment (3,
18 and 33 days) in the environmental temperature (24°C) on the
degradation were studied by response surface methodology (RSM).
The Hunter values (L*, a*, and b*) and the concentration of
canthaxanthin (C, mg/L) illustrated more degradation of this pigment
at low pHs (pH≤ 4) by passing the time (days≥10) with R² 97.00%,
91.31%, 97.60%, and 99.54% for C, L*, a*, and b* respectively. The
predicted model were found to be significant (p
Abstract: Signalized intersections on high-volume arterials are
often congested during peak hours, causing a decrease in through
movement efficiency on the arterial. Much of the vehicle delay
incurred at conventional intersections is caused by high left-turn
demand. Unconventional intersection designs attempt to reduce
intersection delay and travel time by rerouting left-turns away from
the main intersection and replacing it with right-turn followed by Uturn.
The proposed new type of U-turn intersection is geometrically
designed with a raised island which provides a protected U-turn
movement. In this study several scenarios based on different
distances between U-turn and main intersection, traffic volume of
major/minor approaches and percentage of left-turn volumes were
simulated by use of AIMSUN, a type of traffic microsimulation
software. Subsequently some models are proposed in order to
compute travel time of each movement. Eventually by correlating
these equations to some in-field collected data of some implemented
U-turn facilities, the reliability of the proposed models are approved.
With these models it would be possible to calculate travel time of
each movement under any kind of geometric and traffic condition. By
comparing travel time of a conventional signalized intersection with
U-turn intersection travel time, it would be possible to decide on
converting signalized intersections into this new kind of U-turn
facility or not. However comparison of travel time is not part of the
scope of this research. In this paper only travel time of this innovative
U-turn facility would be predicted. According to some before and
after study about the traffic performance of some executed U-turn
facilities, it is found that commonly, this new type of U-turn facility
produces lower travel time. Thus, evaluation of using this type of
unconventional intersection should be seriously considered.
Abstract: In this paper, algorithms for the automatic localisation
of two anatomical soft tissue landmarks of the head the medial
canthus (inner corner of the eye) and the tragus (a small, pointed,
cartilaginous flap of the ear), in CT images are describet. These
landmarks are to be used as a basis for an automated image-to-patient
registration system we are developing. The landmarks are localised
on a surface model extracted from CT images, based on surface
curvature and a rule based system that incorporates prior knowledge
of the landmark characteristics. The approach was tested on a dataset
of near isotropic CT images of 95 patients. The position of the
automatically localised landmarks was compared to the position of
the manually localised landmarks. The average difference was 1.5
mm and 0.8 mm for the medial canthus and tragus, with a maximum
difference of 4.5 mm and 2.6 mm respectively.The medial canthus
and tragus can be automatically localised in CT images, with
performance comparable to manual localisation
Abstract: The purpose of this study is to determine in what
ways elementary education prospective teachers are being informed
about innovations and to explain the role of social influence in the
usage process of a technological innovation in terms of genders. The
study group consisted of 300 prospective teachers, including 234
females and 66 males. Data have been collected by a questionnaire
developed by the researchers. The result of the study showed that,
while prospective teachers are being informed about innovations
most frequently by mass media, they rarely seek to take expert
advice. In addition, analysis of results showed that the social
influence on females were significantly higher than males in usage
process of a technological innovation.
Abstract: A stack with a small critical temperature gradient is
desirable for a standing wave thermoacoustic engine to obtain a low
onset temperature difference (the minimum temperature difference to
start engine-s self-oscillation). The viscous and heat relaxation loss in
the stack determines the critical temperature gradient. In this work, a
dimensionless critical temperature gradient factor is obtained based
on the linear thermoacoustic theory. It is indicated that the
impedance determines the proportion between the viscous loss, heat
relaxation losses and the power production from the heat energy. It
reveals the effects of the channel dimensions, geometrical
configuration and the local acoustic impedance on the critical
temperature gradient in stacks. The numerical analysis shows that
there exists a possible optimum combination of these parameters
which leads to the lowest critical temperature gradient. Furthermore,
several different geometries have been tested and compared
numerically.
Abstract: Ultrasonic machining (USM) is a non-traditional
machining process being widely used for commercial machining of
brittle and fragile materials such as glass, ceramics and
semiconductor materials. However, USM could be a viable
alternative for machining a tough material such as titanium; and this
aspect needs to be explored through experimental research. This
investigation is focused on exploring the use of ultrasonic machining
for commercial machining of pure titanium (ASTM Grade-I) and
evaluation of tool wear rate (TWR) under controlled experimental
conditions. The optimal settings of parameters are determined
through experiments planned, conducted and analyzed using Taguchi
method. In all, the paper focuses on parametric optimization of
ultrasonic machining of pure titanium metal with TWR as response,
and validation of the optimized value of TWR by conducting
confirmatory experiments.
Abstract: Our aim in this piece of work is to demonstrate the
power of the Laplace Adomian decomposition method (LADM) in
approximating the solutions of nonlinear differential equations
governing the two-dimensional viscous flow induced by a shrinking
sheet.
Abstract: Coal fly ash (CFA) generated by coal-based thermal
power plants is mainly composed of some oxides having high
crystallinity, like quartz and mullite. In this study, the effect of CFA
crystallinity toward lead adsorption capacity was investigated. To get
solid with various crystallinity, the solution of sodium hydroxide
(NaOH) of 1-7 M was used to treat CFA at various temperature and
reflux time. Furthermore, to evaluate the effect of NaOH-treated CFA
with respect to adsorption capacity, the treated CFA were examine as
adsorbent for removing lead in the solution. The result shows that
using NaOH to treat CFA causes crystallinity of quartz and mullite
decrease. At higher NaOH concentration (>3M), in addition the
damage of quartz and mullite crystallinity is followed by crystal
formation called hydroxysodalite. The lower crystalllinity, the higher
adsorption capacity.
Abstract: The aim of the article is to describe modern
contemporary systems of employees' remuneration used in
organizations, to give a general overview of these questions based on
the questionnaire survey made by the authors, as well as to assess
possible effects of economic crisis in this area. It is necessary to be
aware of the fact that firm's success in the contemporary business
environment depends not only on the technical equipment, financial
resources, availability of raw materials and information and effective
management, but one of the crucial factors of firm's success is its
human potential. The article emphasizes that the well working
remuneration system has a very important position in the
organization in the broadest sense. The paper also aims to the current
situation in the area of employees' remuneration in one of Czech
Republic regions, in the Moravian-Silesian Region.
Abstract: Normally business changes are made in order to
change a level of activity in some way, whether it is sales, cash flow,
productivity, or product portfolio. When attempts are made to make
such changes, too often the business reverts to the old levels of
activity as soon as management attention is diverted. Risk
management is a field of growing interest to project managers as well
as in general business and organizational management. There are
several approaches used to manage risk in projects and this paper is a
brief outline of some that you might encounter, with an indication of
their strengths and weaknesses.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: This paper has introduced a slope photogrammetric mapping using unmanned aerial vehicle. There are two units of UAV has been used in this study; namely; fixed wing and multi-rotor. Both UAVs were used to capture images at the study area. A consumer digital camera was mounted vertically at the bottom of UAV and captured the images at an altitude. The objectives of this study are to obtain three dimensional coordinates of slope area and to determine the accuracy of photogrammetric product produced from both UAVs. Several control points and checkpoints were established Real Time Kinematic Global Positioning System (RTK-GPS) in the study area. All acquired images from both UAVs went through all photogrammetric processes such as interior orientation, exterior orientation, aerial triangulation and bundle adjustment using photogrammetric software. Two primary results were produced in this study; namely; digital elevation model and digital orthophoto. Based on results, UAV system can be used to mapping slope area especially for limited budget and time constraints project.
Abstract: The householder RLS (HRLS) algorithm is an O(N2)
algorithm which recursively updates an arbitrary square-root of the
input data correlation matrix and naturally provides the LS weight
vector. A data dependent householder matrix is applied for such
an update. In this paper a recursive estimate of the eigenvalue
spread and misalignment of the algorithm is presented at a very low
computational cost. Misalignment is found to be highly sensitive to
the eigenvalue spread of input signals, output noise of the system and
exponential window. Simulation results show noticeable degradation
in the misalignment by increase in eigenvalue spread as well as
system-s output noise, while exponential window was kept constant.
Abstract: Stage bus operated in the mixed traffic might always meet many problems about low quality and reliability of services. The low quality and reliability of bus service can make the system not attractive and directly reduce the interest of using bus service. This paper presents the result of field investigation and analysis of on-time performance and service regularity of stage bus in mixed traffic. Data for analysis was collected from the field by on-board observation along the Ipoh-Lumut corridor in Perak, Malaysia. From analysis and discussion, it can be concluded that on-time performance and service regularity varies depend on station, typical day, time period, operation characteristics of bus and characteristics of traffic. The on-time performance and service regularity of stage bus in mixed traffic can be derived by using data collected by onboard survey. It is clear that on-time performance and service regularity of the existing stage bus system was low.
Abstract: The various applications of VLSI circuits in highperformance
computing, telecommunications, and consumer
electronics has been expanding progressively, and at a very hasty
pace. This paper describes a new model for partitioning a circuit
using DBSCAN and fuzzy ARTMAP neural network. The first step
is concerned with feature extraction, where we had make use
DBSCAN algorithm. The second step is the classification and is
composed of a fuzzy ARTMAP neural network. The performance of
both approaches is compared using benchmark data provided by
MCNC standard cell placement benchmark netlists. Analysis of the
investigational results proved that the fuzzy ARTMAP with
DBSCAN model achieves greater performance then only fuzzy
ARTMAP in recognizing sub-circuits with lowest amount of
interconnections between them The recognition rate using fuzzy
ARTMAP with DBSCAN is 97.7% compared to only fuzzy
ARTMAP.
Abstract: The supply chains (SCs) have to appeal to new management paradigms to improve their ability to respond rapidly and cost effectively to unpredictable changes in markets and increasing levels of environmental turbulence, both in terms of volume and variety. In this highly demanded context, the Agile paradigm provides the capabilities to SC quickly adapt to changes in the market requirements. The purpose of this paper is to suggest an Agile Index to assess the agility of the automotive companies and corresponding SCs. The proposed integrated assessment model incorporates Agile practices weighted according to their importance to the automotive SC competitiveness and obtained from the Delphi technique.