Abstract: This study demonstrates the feasibility of joining the commercial pure copper plates by friction stir welding (FSW). Microstructure, microhardness and tensile properties in terms of the joint efficiency were found 94.03 % compare to as receive base material (BM). The average hardness at the top was higher than bottom. Hardness of weld zone was higher than the base material. Different microstructure zones were revealed by optical microscopy and scanning electron microscopy. The stirred zone (SZ) exhibited primary two phases namely, recrystallized grains and fine precipitates in matrix of copper.
Abstract: In the present paper, we consider the generalized form of Baskakov Durrmeyer operators to study the rate of convergence, in simultaneous approximation for functions having derivatives of bounded variation.
Abstract: In geometrical camera calibration, the objective is to
determine a set of camera parameters that describe the mapping
between 3D references coordinates and 2D image coordinates. In this
paper, a technique of calibration and tracking based on both a least
squares method is presented and a correlation technique developed as
part of an augmented reality system. This approach is fast and it can
be used for a real time system
Abstract: Adenylate kinase (AK) catalyse the phosphotransferase
reaction plays an important role in cellular energy homeostasis. The
inhibitors of bacterial AK are useful in the treatment of several
bacterial infections. To the novel inhibitors of AK, docking studies
performed by using the 3D structure of Bacillus stearothermophilus
adenylate kinase from protein data bank (IZIP). 46 Quinoxaline
analogues were docked in 1ZIP and selected the highly interacting
compounds based on their binding energies, for further studies
Abstract: One of the factors to maintain system survivability is
the adequate reactive power support to the system. Lack of reactive
power support may cause undesirable voltage decay leading to total
system instability. Thus, appropriate reactive power support scheme
should be arranged in order to maintain system stability. The strength
of a system capacity is normally denoted as system loadability. This
paper presents the enhancement of system loadability through
optimal reactive power planning technique using a newly developed
optimization technique, termed as Multiagent Immune Evolutionary
Programming (MAIEP). The concept of MAIEP is developed based
on the combination of Multiagent System (MAS), Artificial Immune
System (AIS) and Evolutionary Programming (EP). In realizing the
effectiveness of the proposed technique, validation is conducted on
the IEEE-26-Bus Reliability Test System. The results obtained from
pre-optimization and post-optimization process were compared
which eventually revealed the merit of MAIEP.
Abstract: This paper deals with motion planning of multiple
mobile robots. Mobile robots working together to achieve several
objectives have many advantages over single robot system. However,
the planning and coordination between the mobile robots is
extremely difficult. In the present investigation rule-based and rulebased-
neuro-fuzzy techniques are analyzed for multiple mobile
robots navigation in an unknown or partially known environment.
The final aims of the robots are to reach some pre-defined goals.
Based upon a reference motion, direction; distances between the
robots and obstacles; and distances between the robots and targets;
different types of rules are taken heuristically and refined later to find
the steering angle. The control system combines a repelling influence
related to the distance between robots and nearby obstacles and with
an attracting influence between the robots and targets. Then a hybrid
rule-based-neuro-fuzzy technique is analysed to find the steering
angle of the robots. Simulation results show that the proposed rulebased-
neuro-fuzzy technique can improve navigation performance in
complex and unknown environments compared to this simple rulebased
technique.
Abstract: The objective of this study was to investigate the effects of dietary supplementation with raw or heat-treated sunflower oil seed with two levels of 7.5% or 15% on unsaturated fatty acids in milk fat and performances of high-yielding lactating cows. Twenty early lactating Holstein cows were used in a complete randomized design. Treatments included: 1) CON, control (without sunflower oil seed). 2) LS-UT, 7.5% raw sunflower oil seed. 3) LS-HT, 7.5% heat-treated sunflower oil seed. 4) HS-UT, 15% raw sunflower oil seed. 5) HS-HT, 15% heat-treated sunflower oil seed. Experimental period lasted for 4 wk, with first 2 wk used for adaptation to the diets. Supplementation with 7.5% raw sunflower seed (LS-UT) tended to decrease milk yield, with 28.37 kg/d compared with the control (34.75 kg/d). Milk fat percentage was increased with the HS-UT treatment that obtained 3.71% compared with CON that was 3.39% and without significant different. Milk protein percent was decreased high level sunflower oil seed treatments (15%) with 3.18% whereas CON treatment is caused 3.40% protein. The cows fed added low sunflower heat-treated (LS-HT) produced milk with the highest content of total unsaturated fatty acid with 32.59 g/100g of milk fat compared with the HS-UT with 23.59 g/100g of milk fat. Content of C18 unsaturated fatty acids in milk fat increased from 21.68 g/100g of fat in the HS-UT to 22.50, 23.98, 27.39 and 30.30 g/100g of fat from the cow fed HS-HT, CON, LS-UT and LS-HT treatments, respectively. C18:2 isomers of fatty acid in milk were greater by LSHT supplementation with significant effect (P < 0.05). Total of C18 unsaturated fatty acids content was significantly higher in milk of animal fed added low heat-treated sunflower (7.5%) than those fed with high sunflower. In all, results of this study showed that diet cow's supplementation with sunflower oil seed tended to reduce milk production of lactating cows but can improve C18 UFA (Unsaturated Fatty Acid) content in milk fat. 7.5% level of sunflower oil seed that heated seemed to be the optimal source to increase UFA production.
Abstract: The paper presents the multi-element synthetic
transmit aperture (MSTA) method with a small number of elements
transmitting and all elements apertures in medical ultrasound
imaging. As compared to the other methods MSTA allows to
increase the system frame rate and provides the best compromise
between penetration depth and lateral resolution.
In the experiments a 128-element linear transducer array with
0.3 mm pitch excited by a burst pulse of 125 ns duration were used.
The comparison of 2D ultrasound images of tissue mimicking
phantom obtained using the STA and the MSTA methods is
presented to demonstrate the benefits of the second approach. The
results were obtained using SA algorithm with transmit and receive
signals correction based on a single element directivity function.
Abstract: The underground shopping mall has the constructional
problem of the fire evacuation. Also, the people sometimes lose their
direction and information of current time in the mall. If the
emergencies such as terrorist explosions or gas explosions are
happened, they have to go out soon. Under such circumstances, inside
of the mall has high risk for life. In this research, the authors propose a
way that he/she can go out from the underground shopping mall
quickly. If the narrow exits are discovered by using active RFID
(Radio Frequency Identification) tags and using cellular phones, they
can evacuate as soon as possible. To verify this hypothesis, the authors
design the model and carry out the agent-based simulation. They treat,
as a case study, the Tenjin mall in Fukuoka Prefecture in Japan. The
result of the simulation is that the case of the pedestrian with using
active RFID tags and cellular phones reduced the amount of time to
spend on the evacuation. Even if the diffusion of RFID tags and
cellular phones was not perfect, they could show the effectiveness of
reducing the time of evacuation.
Abstract: Nowadays the market for industrial companies is becoming more and more globalized and highly competitive, forcing them to shorten the duration of the manufacturing system development time in order to reduce the time to market. In order to achieve this target, the hierarchical systems used in previous manufacturing systems are not enough because they cannot deal effectively with unexpected situations. To achieve flexibility in manufacturing systems, the concept of an Autonomous Decentralized Flexible Manufacturing System (AD-FMS) is useful. In this paper, we introduce a hypothetical reasoning based algorithm called the Algorithm for Future Anticipative Reasoning (AFAR) which is able to decide on a conceivable next action of an Automated Guided Vehicle (AGV) that works autonomously in the AD-FMS.
Abstract: Occurrence of a multiple-points fault in machine operations could result in exhibiting complex fault signatures, which could result in lowering fault diagnosis accuracy. In this study, a multiple-points defect model (MPDM) is proposed which can simulate fault signature-s dynamics for n-points bearing faults. Furthermore, this study identifies that in case of multiple-points fault in the rotary machine, the location of the dominant component of defect frequency shifts depending upon the relative location of the fault points which could mislead the fault diagnostic model to inaccurate detections. Analytical and experimental results are presented to characterize and validate the variation in the dominant component of defect frequency. Based on envelop detection analysis, a modification is recommended in the existing fault diagnostic models to consider the multiples of defect frequency rather than only considering the frequency spectrum at the defect frequency in order to incorporate the impact of multiple points fault.
Abstract: In this paper, we propose a fast and efficient method for drawing very large-scale graph data. The conventional force-directed method proposed by Fruchterman and Rheingold (FR method) is well-known. It defines repulsive forces between every pair of nodes and attractive forces between connected nodes on a edge and calculates corresponding potential energy. An optimal layout is obtained by iteratively updating node positions to minimize the potential energy. Here, the positions of the nodes are updated every global timestep at the same time. In the proposed method, each node has its own individual time and time step, and nodes are updated at different frequencies depending on the local situation. The proposed method is inspired by the hierarchical individual time step method used for the high accuracy calculations for dense particle fields such as star clusters in astrophysical dynamics. Experiments show that the proposed method outperforms the original FR method in both speed and accuracy. We implement the proposed method on the MDGRAPE-3 PCI-X special purpose parallel computer and realize a speed enhancement of several hundred times.
Abstract: The state and stability of hemoglobin adsorbed on the
glass surface was investigated using slab optical waveguide (SOWG)
spectroscopy. The peak position of the absorption band of hemoglobin
adsorbed on the glass surface was same as that of the hemoglobin in
solution. This result suggests that no significant denaturation occurred
by adsorption. The adsorption of hemoglobin is relatively strong that
the hemoglobin molecules even remained adsorbed after rinsing the
cell with buffer solution. The peak shift caused by the reduction of
adsorbed hemoglobin was also observed.
Abstract: This paper addresses a novel technique for placement of distributed generation (DG) in electric power systems. A GA based approach for sizing and placement of DG keeping in view of system power loss minimization in different loading conditions is explained. Minimal system power loss is obtained under voltage and line loading constraints. Proposed strategy is applied to power distribution systems and its effectiveness is verified through simulation results on 16, 37-bus and 75-bus test systems.
Abstract: The evolution of logic circuits, which falls under the heading of evolvable hardware, is carried out by evolutionary algorithms. These algorithms are able to automatically configure reconfigurable devices. One of main difficulties in developing evolvable hardware with the ability to design functional electrical circuits is to choose the most favourable EA features such as fitness function, chromosome representations, population size, genetic operators and individual selection. Until now several researchers from the evolvable hardware community have used and tuned these parameters and various rules on how to select the value of a particular parameter have been proposed. However, to date, no one has presented a study regarding the size of the chromosome representation (circuit layout) to be used as a platform for the evolution in order to increase the evolvability, reduce the number of generations and optimize the digital logic circuits through reducing the number of logic gates. In this paper this topic has been thoroughly investigated and the optimal parameters for these EA features have been proposed. The evolution of logic circuits has been carried out by an extrinsic evolvable hardware system which uses (1+λ) evolution strategy as the core of the evolution.
Abstract: Mixed Reality (MR) is one of the newest technologies
explored in education. It promises the potential to promote teaching
and learning and making learners- experience more “engaging".
However, there still lack of research on designing a virtual learning
environment using MR technology. In this paper, we describe the
Mixed Reality technology, the characteristics of situated learning as
instructional design for virtual environment using mixed reality
technology. We also explain a case study that implemented those
design and also the system overview.
Abstract: In this paper we would like to introduce some of the
best practices of using semantic markup and its significance in the
success of web applications. Search engines are one of the best ways
to reach potential customers and are some of the main indicators of
web sites' fruitfulness. We will introduce the most important
semantic vocabularies which are used by Google and Yahoo.
Afterwards, we will explain the process of semantic markup
implementation and its significance for search engines and other
semantic markup consumers. We will describe techniques for slow
conceiving RDFa markup to our web application for collecting Call
for papers (CFP) announcements.
Abstract: Essential hypertension (HTN) usually clusters with other cardiovascular risk factors such as age, overweight, diabetes, insulin resistance and dyslipidemia. The target organ damage (TOD) such as left ventricular hypertrophy, microalbuminuria (MA), acute coronary syndrome (ACS), stroke and cognitive dysfunction takes place early in course of hypertension. Though the prevalence of hypertension is high in India, the relationship between microalbuminuria and target organ damage in hypertension is not well studied. This study aim at detecting MA in essential hypertension and its relation to severity of HTN, duration of HTN, body mass index (BMI), age and TOD such as HTN retinopathy and acute coronary syndrome The present study was done in 100 patients of essential hypertension non diabetics admitted to B.L.D.E.University-s Sri B.M.Patil Medical College, Bijapur, from October 2008 to April 2011. The patients underwent detailed history and clinical examination. Early morning 5 ml of urine sample was collected & MA was estimated by immunoturbidometry method. The relationship of MA with the duration & severity of HTN, BMI, age, sex and TOD's like hypertensive retinopathy, ACS was assessed by univariate analysis. The prevalence of MA in this study was found to be 63 %. In that 42% were male & 21% were female. In this study a significant association between MA and the duration of hypertension (p = 0.036) & (OR =0.438). Longer the duration of hypertension, more possibility of microalbumin in urine. Also there was a significant association between severity of hypertension and MA (p=0.045) and (OR=0.093). MA was positive in 50 (79.4%) patients out of 63, whose blood pressure was >160/100 mm Hg. In this study a significant association between MA and the grades of hypertensive retinopathy (p =0.011) and acute coronary syndrome (p = 0.041) (OR =2.805). Gender and BMI did not pose high risk for MA in this study.The prevalence of MA in essential hypertension is high in this part of the community and MA will increase the risk of developing target organ damage.Early screening of patients with essential hypertension for MA and aggressive management of positive cases might reduce the burden of chronic kidney diseases and cardiovascular diseases in the community.
Abstract: Numerical studies on race car aerodynamics at wing
in ground effect have been carried out using a steady 3d, double
precision, pressure-based, and standard k-epsilon turbulence model.
Through various parametric analytical studies we have observed that
at a particular speed and ground clearance of the wings a favorable
negative lift was found high at a particular angle of attack for all the
physical models considered in this paper. The fact is that if the
ground clearance height to chord length (h/c) is too small, the
developing boundary layers from either side (the ground and the
lower surface of the wing) can interact, leading to an altered variation
of the aerodynamic characteristics at wing in ground effect. Therefore
a suitable ground clearance must be predicted throughout the racing
for a better performance of the race car, which obviously depends
upon the coupled effects of the topography, wing orientation with
respect to the ground, the incoming flow features and/or the race car
speed. We have concluded that for the design of high performance
and high speed race cars the adjustable wings capable to alter the
ground clearance and the angles of attack is the best design option for
any race car for racing safely with variable speeds.
Abstract: The last two decades witnessed some advances in the development of an Arabic character recognition (CR) system. Arabic CR faces technical problems not encountered in any other language that make Arabic CR systems achieve relatively low accuracy and retards establishing them as market products. We propose the basic stages towards a system that attacks the problem of recognizing online Arabic cursive handwriting. Rule-based methods are used to perform simultaneous segmentation and recognition of word portions in an unconstrained cursively handwritten document using dynamic programming. The output of these stages is in the form of a ranked list of the possible decisions. A new technique for text line separation is also used.