Abstract: The Application of e-health solutions has brought superb advancements in the health care industry. E-health solutions have already been embraced in the industrialized countries. In an effort to catch up with the growth, the developing countries have strived to revolutionize the healthcare industry by use of Information technology in different ways. Based on a technology assessment carried out in Kenya – one of the developing countries – and using multiple case studies in Nyanza Province, this work focuses on an investigation on how five rural hospitals are adapting to the technology shift. The issues examined include the ICT infrastructure and e-health technologies in place, the knowledge of participants in terms of benefits gained through the use of ICT and the challenges posing barriers to the use of ICT technologies in these hospitals. The results reveal that the ICT infrastructure in place is inadequate for e-health implementations as a result to various challenges that exist. Consequently, suggestions on how to tackle the various challenges have been addressed in this paper.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: This study endeavors to evaluate the effects of farmers’ training program on the adoption of improved farming practices, the output of rice farming, and the income as well as the profit from rice farming by employing an ex-post non-experimental data in Sierra Leone. It was established that participating in farmers’ training program increased the possibility of adoption of the improved farming activities that were implemented in the study area. Through the training program also, the proceeds from rice production was also established to have increased considerably. These results were in line with the assumption that one of the main constraints on the growth in agricultural output particularly rice cultivation in most African states is the lack of efficient extension programs.
Abstract: Waterlogging reduces shoot and root growth and final
yield of wheat. Waterlogged sites have a combination of low slope,
high rainfall, heavy texture and low permeability. This study was
aimed the importance of waterlogging on root growth and wheat
yield. In order to study the effects of different waterlogging duration
(0, 10, 20 and 30 days) at growth stages (1-leaf stage, tillering stage
and stem elongation stage) on root growth of wheat cultivars
(Chamran, Vee/Nac and Yavaroos), one pot experiment was carried
out. The experiment was a factorial according to a RCBD with three
replications. Results showed that root dry weight and total root
length in the anthesis and grain ripening stages and biological and
grain yields were significantly different between cultivars, growth
stages and waterlogging durations. Vee/Nac was found superior with
respect to other cultivars. Susceptibility to waterlogging at different
growth stages for cultivars was 1-leaf stage > tillering stage > stem
elongation stage. Under waterlogging treatments, grain and
biological yields, were decreased 44.5 and 39.8%, respectively. Root
length and root dry weight were reduced 55.1 and 45.2%,
respectively, too. In this experiment, decrease at root growth because
of waterlogging reduced grain and biological yields. Based on the
results, even short period (10 days) of waterlogging had
unrecoverable effects on the root growth and grain yield of wheat.
Abstract: Sowing date and density are two important factors in
produce of coriander. A field experiment was conducted with
treatments: sowing time (5 May, 20 May, 4 June and 19 June 2009)
and plant density (10, 30, 50 and 70 plants m-2). The experimental
plots were laid out in a factorial according to a RCBD with three
replications. Results showed that the effect of sowing dates and
densities were significant on grain yield and yield components, but
interaction effects between sowing time and density were non
significant for all of traits in this trial. At sowing times 5 May, 20
May, 4 June and 19 June, grain yield obtained 736.9, 837.8, 1003.1
and 1299.6 kg ha-1, respectively. At 10, 30, 50 and 70 plants m-2,
grain yield were 794.9, 1031.0, 1092.3 and 959.3 kg ha-1,
respectively. In this experiment, sowing at 19 June and 50 and 30
plants m-2 had the most grain yield.
Abstract: The predictability of masonry arch bridges and their
behaviour is widely considered doubtful due to the lack of knowledge
about the conditions of a given masonry arch bridge. The assessment
methods for masonry arch bridges are MEXE, ARCHIE, RING and
Frame Analysis Method. The material properties of the masonry and
fill material are extremely difficult to determine accurately.
Consequently, it is necessary to examine the effect of load dispersal
angle through the fill material, the effect of variations in the stiffness
of the masonry, the tensile strength of the masonry mortar continuum
and the compressive strength of the masonry mortar continuum. It is
also important to understand the effect of fill material on load
dispersal angle to determine their influence on ratings. In this paper a
series of parametric studies, to examine the sensitivity of assessment
ratings to the various sets of input data required by the frame analysis
method, are carried out.
Abstract: Data Envelopment Analysis (DEA) is one of the most
widely used technique for evaluating the relative efficiency of a set
of homogeneous decision making units. Traditionally, it assumes that
input and output variables are known in advance, ignoring the critical
issue of data uncertainty. In this paper, we deal with the problem
of efficiency evaluation under uncertain conditions by adopting the
general framework of the stochastic programming. We assume that
output parameters are represented by discretely distributed random
variables and we propose two different models defined according to a
neutral and risk-averse perspective. The models have been validated
by considering a real case study concerning the evaluation of the
technical efficiency of a sample of individual firms operating in
the Italian leather manufacturing industry. Our findings show the
validity of the proposed approach as ex-ante evaluation technique
by providing the decision maker with useful insights depending on
his risk aversion degree.
Abstract: Optical flow is a research topic of interest for many
years. It has, until recently, been largely inapplicable to real-time
applications due to its computationally expensive nature. This paper
presents a new reliable flow technique which is combined with a
motion detection algorithm, from stationary camera image streams,
to allow flow-based analyses of moving entities, such as rigidity, in
real-time. The combination of the optical flow analysis with motion
detection technique greatly reduces the expensive computation of
flow vectors as compared with standard approaches, rendering the
method to be applicable in real-time implementation. This paper
describes also the hardware implementation of a proposed pipelined
system to estimate the flow vectors from image sequences in real
time. This design can process 768 x 576 images at a very high frame
rate that reaches to 156 fps in a single low cost FPGA chip, which is
adequate for most real-time vision applications.
Abstract: In this paper, Optimum adaptive loading algorithms
are applied to multicarrier system with Space-Time Block Coding
(STBC) scheme associated with space-time processing based on
singular-value decomposition (SVD) of the channel matrix over
Rayleigh fading channels. SVD method has been employed in
MIMO-OFDM system in order to overcome subchannel interference.
Chaw-s and Compello-s algorithms have been implemented to obtain
a bit and power allocation for each subcarrier assuming instantaneous
channel knowledge. The adaptive loaded SVD-STBC scheme is
capable of providing both full-rate and full-diversity for any number
of transmit antennas. The effectiveness of these techniques has
demonstrated through the simulation of an Adaptive loaded SVDSTBC
system, and the comparison shown that the proposed
algorithms ensure better performance in the case of MIMO.
Abstract: Particulate reinforced metal matrix composites
(MMCs) are potential materials for various applications due to their
advantageous of physical and mechanical properties. This paper
presents a study on the performance of stir cast Al2O3 SiC reinforced
metal matrix composite materials. The results indicate that the
composite materials exhibit improved physical and mechanical
properties, such as, low coefficient of thermal expansion, high
ultimate tensile strength, high impact strength, and hardness. It has
been found that with the increase of weight percentage of
reinforcement particles in the aluminium metal matrix, the new
material exhibits lower wear rate against abrasive wearing. Being
extremely lighter than the conventional gray cast iron material, the
Al-Al2O3 and Al-SiC composites could be potential green materials
for applications in the automobile industry, for instance, in making
car disc brake rotors.
Abstract: The investigation results of high-density hydrogen
heating by high-current electric arc are presented at initial pressure
from 5 MPa to 160 MPa with current amplitude up to 1.6 MA and
current rate of rise 109-1011 A/s. When changing the initial pressure
and current rate of rise, channel temperature varies from several
electronvolts to hundreds electronvolts. Arc channel radius is several
millimeters. But the radius of the discharge chamber greater than the
radius of the arc channel on approximately order of magnitude. High
efficiency of gas heating is caused by radiation absorption of
hydrogen surrounding the arc. Current channel consist from vapor of
the initiating wire. At current rate of rise of 109 A/s and relatively
small current amplitude gas heating occurs due to radiation
absorption in the band transparency of hydrogen by the wire vapours
with photon energies less than 13.6 eV. At current rate of rise of
1011 A/s gas heating is due to hydrogen absorption of soft X-rays
from discharge channel.
Abstract: The effect of flooding can be a serious problem for
wheat farmers, even at dry land condition. Amount of flooding
damage depends on duration flooding, developmental stage, wheat
type and variety. Therefore as a factorial experiment in randomized
complete design based on winter bread wheat cultivars (Pishtaz,
Marvdasht, Shiraz, Zarin, Shahriar, C-81-4, Sardari, Agosta seed,
FGS and Azar2) at stages (Non- flooding stress, flooding at tillering
and stem elongation stages for 15 days) carried out in Faculty of
Agriculture, Razi University, Kermanshah, Iran. During flooding,
soil environment of plant roots were water saturated. Analysis of
variance showed that flooding had a significant effect on the number
of grains per spike, grain weight per spike and a grain weight. Hence
flooding reduces the number of grain per spike between 27.1 to 42.5
percent, grain weight per spike between 34.7 to 54.4 percent and
single grain weight between 12.1 to 15.1 percent. Effects of flooding
at the tillering stage reduced higher than stem elongation stage on
studied traits. The result also showed that flooding at tillering stage
delayed spikelet primordial and floret. Between wheat cultivars was
significant for traits, but were different reactions. "Shiraz", "Zarin"
and "Shahriar" had the most no. grain per spike, but "Zarin" and
"Sardari" had the most grain weight per spike and single grain
weight, respectively. Also, interaction between start of flooding and
cultivar was significant.
Abstract: There is a growing interest in the food industry and in preventive health care for the development and evaluation of natural antioxidants from medicinal plant materials. In the present work, extracts of three medicinal plants (Tilia argentea, Crataegi folium leaves and Polygonum bistorta roots) used in Turkish phytotheraphy were screened for their phenolic profiles and antioxidant properties. Crude extracts were obtained from different parts of plants, by solidliquid extraction with pure water, 70% acetone and 70% methanol aqueous solvents. The antioxidant activity of the extracts was determined by ABTS.+ radical cation scavenging activity. The Folin Ciocalteu procedure was used to assess the total phenolic concentrations of the extracts as gallic acid equivalents. A modified liquid chromatography-electro spray ionization-mass spectrometry (LC-ESI-MS) was used to obtain chromatographic profiles of the phenolic compounds in the medicinal plants. The predominant phenolic compounds detected in different extracts of the plants were catechin, protocatechuic and chlorogenic acids. The highest phenolic contents were obtained by using 70% acetone as aqueous solvent, whereas the lowest phenolic contents were obtained by water extraction due to Folin Ciocalteu results. The results indicate that acetone extracts of Tilia argentea had the highest antioxidant capacity as free ABTS radical scavengers. The lowest phenolic contents and antioxidant capacities were obtained from Polygonum bistorta root extracts.
Abstract: fibers of pure cellulose can be made from some bacteria such as acetobacter xylinum. Bacterial cellulose fibers are very pure, tens of nm across and about 0.5 micron long. The fibers are very stiff and, although nobody seems to have measured the strength of individual fibers. Their stiffness up to 70 GPa. Fundamental strengths should be at least greater than those of the best commercial polymers, but best bulk strength seems to about the same as that of steel. They can potentially be produced in industrial quantities at greatly lowered cost and water content, and with triple the yield, by a new process. This article presents a critical review of the available information on the bacterial cellulose as a biological nonwoven fabric with special emphasis on its fermentative production and applications. Characteristics of bacterial cellulose biofabric with respect to its structure and physicochemical properties are discussed. Current and potential applications of bacterial cellulose in textile, nonwoven cloth, paper, films synthetic fiber coating, food, pharmaceutical and other industries are also presented.
Abstract: In this paper, we analyze and test a scheme for the
estimation of electrical fundamental frequency signals from the
harmonic load current and voltage signals.
The scheme was based on using two different Multi Layer
Artificial Neural Networks (ML-ANN) one for the current and the
other for the voltage.
This study also analyzes and tests the effect of choosing the
optimum artificial neural networks- sizes which determine the quality
and accuracy of the estimation of electrical fundamental frequency
signals.
The simulink tool box of the Matlab program for the simulation of
the test system and the test of the neural networks has been used.
Abstract: To study on effect of PEG and NaCl stress on
germination and early seedling stages on two cultivar of corn, two
separated experiment were laid out at physiology laboratory, faculty
of Agriculture, Razi University, Kermanshah, Iran in 2009. This
investigation was performed as factorial experiment under Complete
Randomized Design (CRD) with three replications. Cultivar factor
contains of two varieties (sweet corn SC403 and Flint corn SC704)
and five levels of stress (0, -2, -4, -6 and -8 bar). The principal aim of
current study was to compare the two varieties of maize in relative to
the stress conditions. Results indicated that significant decrease was
observed in percentage of germination, germination rate, length of
radicle and plumule and radicle and plumule dry matter. On the basis
of the results, NaCl as compared with PEG had more effect on
germination and early seedling stage and sweet corn had more
resistant than flint corn in both stress conditions.
Abstract: Most Decision Support Systems (DSS) for waste
management (WM) constructed are not widely marketed and lack
practical applications. This is due to the number of variables and
complexity of the mathematical models which include the
assumptions and constraints required in decision making. The
approach made by many researchers in DSS modelling is to isolate a
few key factors that have a significant influence to the DSS. This
segmented approach does not provide a thorough understanding of
the complex relationships of the many elements involved. The
various elements in constructing the DSS must be integrated and
optimized in order to produce a viable model that is marketable and
has practical application. The DSS model used in assisting decision
makers should be integrated with GIS, able to give robust prediction
despite the inherent uncertainties of waste generation and the plethora
of waste characteristics, and gives optimal allocation of waste stream
for recycling, incineration, landfill and composting.
Abstract: Environmental awareness and the recent
environmental policies have forced many electric utilities to
restructure their operational practices to account for their emission
impacts. One way to accomplish this is by reformulating the
traditional economic dispatch problem such that emission effects are
included in the mathematical model. This paper presents a Particle
Swarm Optimization (PSO) algorithm to solve the Economic-
Emission Dispatch problem (EED) which gained recent attention due
to the deregulation of the power industry and strict environmental
regulations. The problem is formulated as a multi-objective one with
two competing functions, namely economic cost and emission
functions, subject to different constraints. The inequality constraints
considered are the generating unit capacity limits while the equality
constraint is generation-demand balance. A novel equality constraint
handling mechanism is proposed in this paper. PSO algorithm is
tested on a 30-bus standard test system. Results obtained show that
PSO algorithm has a great potential in handling multi-objective
optimization problems and is capable of capturing Pareto optimal
solution set under different loading conditions.
Abstract: Discharges in hydrogen, ignited by wire explosion, with current amplitude up to 1.5 MA were investigated. Channel diameter oscillations were observed on the photostreaks. Voltage and current curves correlated with the photostreaks. At initial gas pressure of 5-35 MPa the oscillation period was proportional to square root of atomic number of the initiating wire material. These oscillations were associated with aligned magnetic and gas-kinetic pressures. At initial pressure of 80-160 MPa acoustic pressure fluctuations on the discharge chamber wall were increased up to 150 MPa and there were the growth of voltage fluctuations on the discharge gap up to 3 kV simultaneously with it. In some experiments it was observed abrupt increase in the oscillation amplitude, which can be caused by the resonance of the acoustic oscillations in discharge chamber volume and the oscillations connected with alignment of the gaskinetic pressure and the magnetic pressure, as far as frequencies of these oscillations are close to each other in accordance with the estimates and the experimental data. Resonance of different type oscillations can produce energy density increasing in the discharge channel. Thus, the appropriate initial conditions in the experiment allow to increase the energy density in the discharge channel
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.