Abstract: Linear stability of wake-shear layers in two-phase
shallow flows is analyzed in the present paper. Stability analysis is
based on two-dimensional shallow water equations. It is assumed that
the fluid contains uniformly distributed solid particles. No dynamic
interaction between the carrier fluid and particles is expected in the
initial moment. Linear stability curves are obtained for different
values of the particle loading parameter, the velocity ratio and the
velocity deficit. It is shown that the increase in the velocity ratio
destabilizes the flow. The particle loading parameter has a stabilizing
effect on the flow. The role of the velocity deficit is also
destabilizing: the increase of the velocity deficit leads to less stable
flow.
Abstract: In this paper we introduce three watermarking methods that can be used to count the number of times that a user has played some content. The proposed methods are tested with audio content in our experimental system using the most common signal processing attacks. The test results show that the watermarking methods used enable the watermark to be extracted under the most common attacks with a low bit error rate.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetically and thermal stresses remain major failures
for insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: In this paper, a wavelet-based neural network (WNN) classifier for recognizing EEG signals is implemented and tested under three sets EEG signals (healthy subjects, patients with epilepsy and patients with epileptic syndrome during the seizure). First, the Discrete Wavelet Transform (DWT) with the Multi-Resolution Analysis (MRA) is applied to decompose EEG signal at resolution levels of the components of the EEG signal (δ, θ, α, β and γ) and the Parseval-s theorem are employed to extract the percentage distribution of energy features of the EEG signal at different resolution levels. Second, the neural network (NN) classifies these extracted features to identify the EEGs type according to the percentage distribution of energy features. The performance of the proposed algorithm has been evaluated using in total 300 EEG signals. The results showed that the proposed classifier has the ability of recognizing and classifying EEG signals efficiently.
Abstract: The photoluminescence (PL) at 1.55 μm from
semiconducting β-FeSi2 has attracted a noticeable interest for
silicon-based optoelectronic applications. Moreover, its high optical
absorption coefficient (higher than 105 cm-1 above 1.0 eV) allows this
semiconducting material to be used as photovoltanics devices.
A clear PL spectrum for β-FeSi2 was observed by Cu or Au coating
on Si(001). High-crystal-quality β-FeSi2 with a low-level nonradiative
center was formed on a Cu- or Au- reated Si layer. This method of
deposition can be applied to other materials requiring high crystal
quality.
Abstract: The problem of natural convection about a cone embedded in a porous medium at local Rayleigh numbers based on the boundary layer approximation and the Darcy-s law have been studied before. Similarity solutions for a full cone with the prescribed wall temperature or surface heat flux boundary conditions which is the power function of distance from the vertex of the inverted cone give us a third-order nonlinear differential equation. In this paper, an approximate method for solving higher-order ordinary differential equations is proposed. The approach is based on a rational Chebyshev Tau (RCT) method. The operational matrices of the derivative and product of rational Chebyshev (RC) functions are presented. These matrices together with the Tau method are utilized to reduce the solution of the higher-order ordinary differential equations to the solution of a system of algebraic equations. We also present the comparison of this work with others and show that the present method is applicable.
Abstract: This paper presents a developed method for
controlling multi-renewable energy generators. The control system
depends basically on three sensors (wind anemometer, solar sensor,
and voltage sensor). These sensors represent PLC-s analogue inputs.
Controlling the output voltage supply can be achieved by an
enhanced method of interlocking between the renewable energy
generators, depending on those sensors and output contactors.
Abstract: This article presents new current-mode oscillator circuits using CDTAs which is designed from block diagram. The proposed circuits consist of two CDTAs and two grounded capacitors. The condition of oscillation and the frequency of oscillation can be adjusted by electronic method. The circuits have high output impedance and use only grounded capacitors without any external resistor which is very appropriate to future development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: A new paradigm for software design and development models software by its business process, translates the model into a process execution language, and has it run by a supporting execution engine. This process-oriented paradigm promotes modeling of software by less technical users or business analysts as well as rapid development. Since business process models may be shared by different organizations and sometimes even by different business domains, it is interesting to apply a technique used in traditional software component technology to design reusable business processes. This paper discusses an approach to apply a technique for software component fabrication to the design of process-oriented software units, called process components. These process components result from decomposing a business process of a particular application domain into subprocesses with an aim that the process components can be reusable in different process-based software models. The approach is quantitative because the quality of process component design is measured from technical features of the process components. The approach is also strategic because the measured quality is determined against business-oriented component management goals. A software tool has been developed to measure how good a process component design is, according to the required managerial goals and comparing to other designs. We also discuss how we benefit from reusable process components.
Abstract: Temperature dependence of force of gravitation is one
of the fundamental problems of physics. This problem has got special
value in connection with that the general theory of relativity,
supposing the weakest positive influence of a body temperature on its
weight, actually rejects an opportunity of measurement of negative
influence of temperature on gravity in laboratory conditions. Really,
the recognition of negative temperature dependence of gravitation,
for example, means basic impossibility of achievement of a
singularity («a black hole») at a gravitational collapse. Laboratory
experiments with exact weighing the heated up metal samples,
indicating negative influence temperatures of bodies on their physical
weight are described. Influence of mistakes of measurements is
analyzed. Calculations of distribution of temperature in volume of the
bar, agreed with experimental data of time dependence of weight of
samples are executed. The physical substantiation of negative
temperature dependence of weight of the bodies, based on correlation
of acceleration at thermal movement of micro-particles of a body and
its absolute temperature, are given.
Abstract: A Data Warehouses is a repository of information
integrated from source data. Information stored in data warehouse is
the form of materialized in order to provide the better performance
for answering the queries. Deciding which appropriated views to be
materialized is one of important problem. In order to achieve this
requirement, the constructing search space close to optimal is a
necessary task. It will provide effective result for selecting view to be
materialized. In this paper we have proposed an approach to reoptimize
Multiple View Processing Plan (MVPP) by using global
common subexpressions. The merged queries which have query
processing cost not close to optimal would be rewritten. The
experiment shows that our approach can help to improve the total
query processing cost of MVPP and sum of query processing cost
and materialized view maintenance cost is reduced as well after views
are selected to be materialized.
Abstract: It is known that an analog Hopfield neural network
with time delay can generate the outputs which are similar to the
human electroencephalogram. To gain deeper insights into the
mechanisms of rhythm generation by the Hopfield neural networks
and to study the effects of noise on their activities, we investigated
the behaviors of the networks with symmetric and asymmetric
interneuron connections. The neural network under the study consists
of 10 identical neurons. For symmetric (fully connected) networks all
interneuron connections aij = +1; the interneuron connections for
asymmetric networks form an upper triangular matrix with non-zero
entries aij = +1. The behavior of the network is described by 10
differential equations, which are solved numerically. The results of
simulations demonstrate some remarkable properties of a Hopfield
neural network, such as linear growth of outputs, dependence of
synchronization properties on the connection type, huge
amplification of oscillation by the external uniform noise, and the
capability of the neural network to transform one type of noise to
another.
Abstract: Possible advantages of technology in educational
context required the defining boundaries of formal and informal
learning. Increasing opportunity to ubiquitous learning by
technological support has revealed a question of how to discover
the potential of individuals in the spontaneous environments such as
social networks. This seems to be related with the question of what
purposes in social networks have been being used? Social networks
provide various advantages in educational context as collaboration,
knowledge sharing, common interests, active participation and
reflective thinking. As a consequence of these, the purpose of this
study is composed of proposing a new model that could determine
factors which effect adoption of social network applications for usage
in educational context. While developing a model proposal, the
existing adoption and diffusion models have been reviewed and they
are thought to be suitable on handling an original perspective instead
of using completely other diffusion or acceptance models because of
different natures of education from other organizations. In the
proposed model; social factors, perceived ease of use, perceived
usefulness and innovativeness are determined four direct constructs
that effect adoption process. Facilitating conditions, image,
subjective norms and community identity are incorporated to model
as antecedents of these direct four constructs.
Abstract: The relics of traditional folk culture in Kazakhstan are ceremonies or their fragments - such as weddings, funerals, shamanism. The world of spiritual creatures, spirits-protectors, spirits-helpers, injury spirits, spirits of illnesses, etc., is described in detail in shamanic rites (in Kazakh culture it is called bakslyk). The study of these displays of folk culture, which reflect the peoples` ethnic mentality or notions about the structure, values and hierarchies of the universe, includes collection and recording of the field materials and their interpretation, i.e. reconstruction of those meanings which were initially embodied or “coded" in folklore. A distinctive feature of Kazakh nomadic culture is its self-preservation and actualization, almost untouched the ancient mythologies of the world, in particular, the mythologies connected with music, musical instruments and the creator of music. Within the frameworks of the traditional culture the word and the music keep the sacral meaning. The ritual melodies and what they carry – the holly, and at the same time unexplored, powerful and threatening, uncontrolled by people world – keep on attributing the soul to all, connected with culture.
Abstract: Early supplier involvement (ESI) benefits new
product development projects several ways. Nevertheless, many castuser
companies do not know the advantages of ESI and therefore do
not utilize it. This paper presents reasons why to utilize ESI in
casting industry and how that can be done. Further, this paper
presents advantages and challenges related to ESI in casting industry,
and introduces a Casting-Network Collaboration Model. The model
presents practices for companies to build advantageous collaborative
relationships. More detailed, the model describes three levels for
company-network relationships in casting industry with different
degrees of collaboration, and requirements for operating in each
level. In our research, ESI was found to influence, for example, on
project time, component cost, and quality. In addition, challenges
related to ESI, such as, a lack of mutual trust and unawareness about
the advantages were found. Our research approach was a case study
including four cases.
Abstract: Through the course of this paper we define Business Case Management and its characteristics, and highlight its link to knowledge workers. Business Case Management combines knowledge and process effectively, supporting the ad hoc and unpredictable nature of cases, and coordinate a range of other technologies to appropriately support knowledge-intensive processes. We emphasize the growing importance of knowledge workers and the current poor support for knowledge work automation. We also discuss the challenges in supporting this kind of knowledge work and propose a novel approach to overcome these challenges.
Abstract: The importance of low power consumption is widely
acknowledged due to the increasing use of portable devices, which
require minimizing the consumption of energy. Energy dissipation is
heavily dependent on the software used in the system. Applying
design patterns in object-oriented designs is a common practice
nowadays. In this paper we analyze six design patterns and explore
the effect of them on energy consumption and performance.
Abstract: A hybrid feature based adaptive particle filter algorithm is presented for object tracking in real scenarios with static camera.
The hybrid feature is combined by two effective features: the Grayscale Arranging Pairs (GAP) feature and the color histogram feature. The GAP feature has high discriminative ability even under conditions of severe illumination variation and dynamic background
elements, while the color histogram feature has high reliability to identify the detected objects. The combination of two features covers the shortage of single feature. Furthermore, we adopt an updating
target model so that some external problems such as visual angles can be overcame well. An automatic initialization algorithm is introduced which provides precise initial positions of objects. The experimental
results show the good performance of the proposed method.
Abstract: In this paper, we introduce GODYS-PC software
package for modeling, simulating and analyzing dynamic systems.
To illustrate the use of GODYS-PC we present a few examples
which concern modeling and simulating of engineering systems. In
order to compare GODYS-PC with widely used in academia and
industry Simulink®, the same examples are provided both in
GODYS-PC and Simulink®.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.