Abstract: Construction of geo-spatial information recently tends to develop as multi-dimensional geo-spatial information. People constructing spatial information is also expanding its area to the general public from some experts. As well as, studies are in progress using a variety of devices, with the aim of near real-time update. In this paper, getting the stereo images using GoPro device used widely also to the general public as well as experts. And correcting the distortion of the images, then by using SIFT, DLT, is acquired the point clouds. It presented a possibility that on the basis of this experiment, using a video device that is readily available in real life, to create a real-time digital map.
Abstract: Appropriate selection of lifting equipments for a high-rise building construction project is one of the important factors to the project’s success. Proper position of a tower crane on a construction site is so important to be determined by an expert or an experienced construction manager who draws working range of a tower crane and moves it over a 2D (dimensional) site layout plan. But it is not usual to use 3D CAD, BIM or virtual reality for temporary facility planning or selection of a tower crane. This study proposes a method to use augmented reality to select proper position of tower cranes. An augmented reality prototype is implemented on a smart device to verify the practicability of the proposed method.
Abstract: AAM has been successfully applied to face alignment,
but its performance is very sensitive to initial values. In case the initial
values are a little far distant from the global optimum values, there
exists a pretty good possibility that AAM-based face alignment may
converge to a local minimum. In this paper, we propose a progressive
AAM-based face alignment algorithm which first finds the feature
parameter vector fitting the inner facial feature points of the face and
later localize the feature points of the whole face using the first
information. The proposed progressive AAM-based face alignment
algorithm utilizes the fact that the feature points of the inner part of the
face are less variant and less affected by the background surrounding
the face than those of the outer part (like the chin contour). The
proposed algorithm consists of two stages: modeling and relation
derivation stage and fitting stage. Modeling and relation derivation
stage first needs to construct two AAM models: the inner face AAM
model and the whole face AAM model and then derive relation matrix
between the inner face AAM parameter vector and the whole face
AAM model parameter vector. In the fitting stage, the proposed
algorithm aligns face progressively through two phases. In the first
phase, the proposed algorithm will find the feature parameter vector
fitting the inner facial AAM model into a new input face image, and
then in the second phase it localizes the whole facial feature points of
the new input face image based on the whole face AAM model using
the initial parameter vector estimated from using the inner feature
parameter vector obtained in the first phase and the relation matrix
obtained in the first stage. Through experiments, it is verified that the
proposed progressive AAM-based face alignment algorithm is more
robust with respect to pose, illumination, and face background than the
conventional basic AAM-based face alignment algorithm.
Abstract: Phase error in communications systems degrades error
performance. In this paper, we present a simple approximation for the
average error probability of the binary phase shift keying (BPSK) in
the presence of phase error having a uniform distribution on arbitrary
intervals. For the simple approximation, we use symmetry and
periodicity of a sinusoidal function. Approximate result for the
average error probability is derived, and the performance is verified
through comparison with simulation result.
Abstract: As we make progressive products for good works, and
future industries want to get higher speed and resolution from various
developments in the robotics as well as precise control system, the
concept of control feedback is getting more important. Within a range
of industrial developments, the concept is most responsible for the
high reliability of a device. We explain an efficient analyzing method
of a rotary encoder such as an incremental type encoder and absolute
type encoder using the LabVIEW program
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: Wireless sensor networks are consisted of hundreds or
thousands of small sensors that have limited resources.
Energy-efficient techniques are the main issue of wireless sensor
networks. This paper proposes an energy efficient agent-based
framework in wireless sensor networks. We adopt biologically
inspired approaches for wireless sensor networks. Agent operates
automatically with their behavior policies as a gene. Agent aggregates
other agents to reduce communication and gives high priority to nodes
that have enough energy to communicate. Agent behavior policies are
optimized by genetic operation at the base station. Simulation results
show that our proposed framework increases the lifetime of each node.
Each agent selects a next-hop node with neighbor information and
behavior policies. Our proposed framework provides self-healing,
self-configuration, self-optimization properties to sensor nodes.
Abstract: Tumor cells have an invasive and metastatic phenotype
that is the main cause of death for cancer patients. Tumor
establishment and penetration consists of a series of complex
processes involving multiple changes in gene expression. In this study,
intraperitoneal administration of a high concentration of ascorbic acid
inhibited tumor establishment and decreased tumor mass in BALB/C
mice implanted with S-180 sarcoma cancer cells. To identify proteins
involved in the ascorbic acid-mediated inhibition of tumor
progression, changes in the tumor proteome associated with ascorbic
acid treatment of BALB/C mice implanted with S-180 were
investigated using two-dimensional gel electrophoresis and mass
spectrometry. Twenty protein spots were identified whose expression
was different between control and ascorbic acid treatment groups.
Abstract: The cables in a nuclear power plant are designed to be
used for about 40 years in safe operation environment. However, the
heat and radiation in the nuclear power plant causes the rapid
performance deterioration of cables in nuclear vessels and heat
exchangers, which requires cable lifetime estimation. The most
accurate method of estimating the cable lifetime is to evaluate the
cables in a laboratory. However, removing cables while the plant is
operating is not allowed because of its safety and cost. In this paper, a
robot system to estimate the cable lifetime in nuclear power plants is
developed and tested. The developed robot system can calculate a
modulus value to estimate the cable lifetime even when the nuclear
power plant is in operation.
Abstract: Air conditioning is mainly to be used as human
comfort medium. It has been use more often in country in which the
daily temperatures are high. In scientific, air conditioning is defined
as a process of controlling the moisture, cooling, heating and cleaning
air. Without proper estimation of cooling load, big amount of waste
energy been used because of unsuitable of air conditioning system are
not considering to overcoming heat gains from surrounding. This is
due to the size of the room is too big and the air conditioning has to
use more energy to cool the room and the air conditioning is too
small for the room. The studies are basically to develop a program to
calculate cooling load. Through this study it is easy to calculate
cooling load estimation. Furthermore it-s help to compare the cooling
load estimation by hourly and yearly. Base on the last study that been
done, the developed software are not user-friendly. For individual
without proper knowledge of calculating cooling load estimation
might be problem. Easy excess and user-friendly should be the main
objective to design something. This program will allow cooling load
able be estimate by any users rather than estimation by using rule of
thumb. Several of limitation of case study is judged to sure it-s
meeting to Malaysia building specification. Finally validation is done
by comparison manual calculation and by developed program.
Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: Protein subchloroplast locations are correlated with its
functions. In contrast to the large amount of available protein
sequences, the information of their locations and functions is less
known. The experiment works for identification of protein locations
and functions are costly and time consuming. The accurate prediction
of protein subchloroplast locations can accelerate the study of
functions of proteins in chloroplast. This study proposes a Random
Forest based method, ChloroRF, to predict protein subchloroplast
locations using interpretable physicochemical properties. In addition
to high prediction accuracy, the ChloroRF is able to select important
physicochemical properties. The important physicochemical
properties are also analyzed to provide insights into the underlying
mechanism.
Abstract: Horizontal platform system (HPS) is popularly applied
in offshore and earthquake technology, but it is difficult and
time-consuming for regulation. In order to understand the nonlinear
dynamic behavior of HPS and reduce the cost when using it, this paper
employs differential transformation method to study the bifurcation
behavior of HPS. The numerical results reveal a complex dynamic
behavior comprising periodic, sub-harmonic, and chaotic responses.
Furthermore, the results reveal the changes which take place in the
dynamic behavior of the HPS as the external torque is increased.
Therefore, the proposed method provides an effective means of
gaining insights into the nonlinear dynamics of horizontal platform
system.
Abstract: Human pose estimation can be executed using Active Shape Models. The existing techniques for applying to human-body research using Active Shape Models, such as human detection, primarily take the form of silhouette of human body. This technique is not able to estimate accurately for human pose to concern two arms and legs, as the silhouette of human body represents the shape as out of round. To solve this problem, we applied the human body model as stick-figure, “skeleton". The skeleton model of human body can give consideration to various shapes of human pose. To obtain effective estimation result, we applied background subtraction and deformed matching algorithm of primary Active Shape Models in the fitting process. The images which were used to make the model were 600 human bodies, and the model has 17 landmark points which indicate body junction and key features of human pose. The maximum iteration for the fitting process was 30 times and the execution time was less than .03 sec.
Abstract: In order to supplement the brittle property of concrete,
fibers are added into concrete mixtures. Compared to general concrete,
various characteristics such as tensile strength, bending strength,
bending toughness, and resistance to crack are superior, and even
when cracks occur, improvements on toughness as well as resistance
to shock are excellent due to the growth of fracture energy. Increased
function of steel fiber reinforced concrete can be differentiated
depending on the fiber dispersion, and sand percentage can be an
important influence on the fiber dispersion. Therefore, in this research,
experiments were planned on sand percentage in order to apprehend
the influence of sand percentage on the bending properties and direct
tension of SFRC and basic experiments were conducted on bending
and direct tension in order to recognize the properties of bending
properties and direct tension following the size of the aggregates and
sand percentage.
Abstract: The ability to recognize humans and their activities by computer vision is a very important task, with many potential application. Study of human motion analysis is related to several research areas of computer vision such as the motion capture, detection, tracking and segmentation of people. In this paper, we describe a segmentation method for extracting human body contour in modified HLS color space. To estimate a background, the modified HLS color space is proposed, and the background features are estimated by using the HLS color components. Here, the large amount of human dataset, which was collected from DV cameras, is pre-processed. The human body and its contour is successfully extracted from the image sequences.
Abstract: This paper attempts to discuss the spam issue from the Malaysian e-mail users- perspective. The purpose is to discover how Malaysian users handle the spam e-mail problem. From the experiences we hope to discover the necessary effort needed to be undertaken to face this problem in the context of Malaysia. A survey was conducted to understand how Malaysian individual perceived spam and what they actually do with the spam e-mail they received in their daily life. The findings indicate that the level of awareness on spam issue in action is still low and need some extra effort by government and relevant agencies to increase their level of awareness.
Abstract: We fabricated the inverted-staggered etch stopper
structure oxide-based TFT and investigated the characteristics of oxide
TFT under the 400 nm wavelength light illumination. When 400 nm
light was illuminated, the threshold voltage (Vth) decreased and
subthreshold slope (SS) increased at forward sweep, while Vth and SS
were not altered when larger wavelength lights, such as 650 nm, 550
nm and 450 nm, were illuminated. At reverse sweep, the transfer curve
barely changed even under 400 nm light. Our experimental results
support that photo-induced hole carriers are captured by donor-like
interface trap and it caused the decrease of Vth and increase of SS. We
investigated the interface trap density increases proportionally to the
photo-induced hole concentration at active layer.
Abstract: Recent widespread use of information and
communication technology has greatly changed information security
risks that businesses and institutions encounter. Along with this
situation, in order to ensure security and have confidence in electronic
trading, it has become important for organizations to take competent
information security measures to provide international confidence that
sensitive information is secure. Against this backdrop, the approach to
information security checking has come to an important issue, which
is believed to be common to all countries. The purpose of this paper is
to introduce the new system of information security checking program
in Korea and to propose synthetic information security
countermeasures under domestic circumstances in order to protect
physical equipment, security management and technology, and the
operation of security check for securing services on ISP(Internet
Service Provider), IDC(Internet Data Center), and
e-commerce(shopping malls, etc.)
Abstract: Despite of the preponderant role played by cement among the construction materials, it is today considered as a material destructing the environment due to the large quantities of carbon dioxide exhausted during its manufacture. Besides, global warming is now recognized worldwide as the new threat to the humankind against which advanced countries are investigating measures to reduce the current amount of exhausted gases to the half by 2050. Accordingly, efforts to reduce green gases are exerted in all industrial fields. Especially, the cement industry strives to reduce the consumption of cement through the development of alkali-activated geopolymer mortars using industrial byproducts like bottom ash. This study intends to gather basic data on the flowability and strength development characteristics of alkali-activated geopolymer mortar by examining its FT-IT features with respect to the effects and strength of the alkali-activator in order to develop bottom ash-based alkali-activated geopolymer mortar. The results show that the 35:65 mass ratio of sodium hydroxide to sodium silicate is appropriate and that a molarity of 9M for sodium hydroxide is advantageous. The ratio of the alkali-activators to bottom ash is seen to have poor effect on the strength. Moreover, the FT-IR analysis reveals that larger improvement of the strength shifts the peak from 1060 cm–1 (T-O, T=Si or Al) toward shorter wavenumber.