Abstract: Few people would dispute the fact that one of the most common applications of energy is creating comfort in buildings, so it is probably true to say that management of energy consumption is required due to the environmental issues and increasing the efficiency of mechanical systems. From the geographical point of view, Iran is located in a warm and semi-arid region; therefore, air-cooled chillers are usually used for cooling residential buildings, commercial buildings, medical buildings, etc. In this study, a heat exchanger was designed for providing laundry hot water by utilizing condenser heat lost base on analytical results of a 540-bed hospital in the city of Mashhad in Iran. In this paper, by using the analytical method, energy consumption reduces about 13%, and coefficient of performance increases a bit. Results show that this method can help in the management of energy consumption a lot.
Abstract: NiTi alloys possess magnificent superelastic, shape memory, high strength and biocompatible properties. For improving mechanical properties, foremost, superelasticity behavior, heat treatment process is carried out. In this paper, two different heat treatment methods were undertaken: (1) solid solution, and (2) aging. The effect of each treatment in a constant time is investigated. Five samples were prepared to study the structure and optimize mechanical properties under different time and temperature. For measuring the upper plateau stress, lower plateau stress and residual strain, tensile test is carried out. The samples were aged at two different temperatures to see difference between aging temperatures. The sample aged at 500 °C has a bigger crystallite size and lower amount of Ni which causes the mentioned sample to possess poor pseudo elasticity behaviour than the other aged sample. The sample aged at 460 °C has shown remarkable superelastic properties. The mentioned sample’s higher plateau is 580 MPa with the lowest residual strain (0.17%) while other samples have possessed higher residual strains. X-ray diffraction was used to investigate the produced phases.
Abstract: Multifunctional bioactive glasses (BGs) are designed with a focus on the provision of bactericidal and biological properties desired for angiogenesis, osteogenesis, and ultimately potential applications in bone tissue engineering. To achieve these, six sol-gel copper/magnesium substituted derivatives of 58S-BG, i.e. a mol% series of 60SiO2-4P2O5-5CuO-(31-x) CaO/xMgO (where x=0, 1, 3, 5, 8, and 10), were synthesized. Afterwards, the effect of MgO/CaO substitution on the in vitro formation of nano-hydroxyapatite (HA), osteoblast-like cell responses and BGs antibacterial performance were studied. During the BGs synthesis, the elimination of nitrates was achieved at 700 °C that prevented the BGs crystallization and stabilized the obtained dried gels. The structural and morphological evaluations were performed with X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). These characterizations revealed that Cu-substituted 58S-BG consisting of 5 mol% MgO (BG-5/5) slightly had retarded the formation of HA. In addition, Cu-substituted 58S-BGs consisting 8 mol% and 10 mol% MgO (BG-5/8 and BG-5/10) displayed lower bioactivity probably due to the lower ion release rate of Ca–Si into the simulated body fluid (SBF). The determination of 3-(4, 5 dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide (MTT) and alkaline phosphate (ALP) activities proved that the highest values of both differentiation and proliferation of MC3T3-E1 cells can be obtained from a 5 mol% MgO substituted BG, while the over addition of MgO (8 mol% and 10 mol%) decreased the bioactivity. Furthermore, these novel Cu/Mg-substituted 58S-BGs displayed antibacterial effect against methicillin-resistant Staphylococcus aureus bacteria. Taken together, the results suggest the equally-substituted BG-5/5 (i.e. the one consists of 5 mol% of both CuO and MgO) as a promising candidate for bone tissue engineering, among all newly designed BGs in this work, owing to its desirable cell proliferation, ALP activity and antibacterial properties.
Abstract: Today, the treatment of cancer, in a relatively short
period, with minimum adverse effects is a great concern for
oncologists. In this paper, based on a recently used mathematical
model for cancer, a guideline has been proposed for the amount
and duration of drug doses for cancer treatment by immunotherapy.
Dynamically speaking, the mathematical ordinary differential
equation (ODE) model of cancer has different equilibrium points;
one of them is unstable, which is called the no tumor equilibrium
point. In this paper, based on the number of tumor cells an
intelligent soft computing controller (a combination of fuzzy logic
controller and genetic algorithm), decides regarding the amount
and duration of drug doses, to eliminate the tumor cells and
stabilize the unstable point in a relatively short time. Two different
immunotherapy approaches; active and adoptive, have been studied
and presented. It is shown that the rate of decay of tumor cells is
faster and the doses of drug are lower in comparison with the result
of some other literatures. It is also shown that the period of
treatment and the doses of drug in adoptive immunotherapy are
significantly less than the active method. A recommendation to
oncologists has also been presented.
Abstract: In the interest-free banking system of Iran, the savings of society are in the form of bank deposits, and banks using the Islamic contracts, allocate the resources to applicants for obtaining facilities and credit. In the meantime, the central bank, with the aim of introducing monetary policy, determines the maximum interest rate on bank deposits in terms of macroeconomic requirements. But in recent years, the country's economic constraints with the stagflation and the consequence of the institutional weaknesses of the financial market of Iran have resulted in massive disturbances in the balance sheet of the banking system, resulting in a period of mismatch maturity in the banks' assets and liabilities and the implementation of a Ponzi game. This issue caused determination of the interest rate in long-term bank deposit contracts to be associated with non-observance of the maximum rate set by the central bank. The result of this condition was in the allocation of new sources of equipment to meet past commitments towards the old depositors and, as a result, a significant part of the supply of equipment was leaked out of the facilitating cycle and credit crunch emerged. The purpose of this study is to identify the most important factors affecting the occurrence of non-confirmatory financial banking behavior using data from 19 public and private banks of Iran. For this purpose, the causes of this non-confirmatory behavior of banks have been investigated using the panel vector autoregression method (PVAR) for the period of 2007-2015. Granger's causality test results suggest that the return of parallel markets for bank deposits, non-performing loans and the high share of the ratio of facilities to banks' deposits are all a cause of the formation of non-confirmatory behavior. Also, according to the results of impulse response functions and variance decomposition, NPL and the ratio of facilities to deposits have the highest long-term effect and also have a high contribution to explaining the changes in banks' non-confirmatory behavior in determining the interest rate on deposits.
Abstract: The main purpose of this study was to explore the role of organisational effectiveness (OE) in seaports. OE is an important managerial concept, one that is necessary for leaders and directors in any organisation to understand the output of their work. OE has been applied in many organisations; however, it is a vital concept in the port business. This paper examines various approaches and applications of the OE concept to business management, and describes benefits that are important and applicable to seaport management. This research reviews and classifies articles published in relevant journals and books between 1950 and 2016; from the general literature on OE to the narrower field of OE in seaports. Based on the extensive literature review, this study identifies and discusses several issues relevant to both practices and theories of this concept. The review concludes by presenting a gap in the literature, as it found only a limited amount of research that endeavours to clarify OE in the seaport sector. As a result of this gap, seaports suffer from a lack of empirical study and are largely neglected in this subject area. The implementation of OE in this research has led to the maritime sector interfacing with different disciplines in order to acquire the advantage of enhancing managerial knowledge and competing successfully in the international marketplace.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: The objective of this study was to determine effect of
dietary essential oil (EO) compounds, which contained
cinnamaldehyde, eugenol, peppermint, coriander, cumin, lemongrass,
and an organic carrier on feed intake, milk composition, and rumen
fermentation of dairy cows during heat exposure. Thirty-two Holstein
cows (days in milk= 60 ± 5) were assigned to one of two treatment
groups: a Control and EO fed. The experiment lasted 28 days. Dry
matter intake (DMI) was measured daily while and milk production
was measured weekly. Our result showed that DMI and milk yield
was decreased (P < 0.01) in control cows relative to EO cows.
Furthermore, supplementation with EO was associated with a
decrease in the molar proportion of propionate (P < 0.05) and
increase (P < 0.05) in acetate to propionate ratio. In conclusion, EO
supplementations in diets can be useful nutritional modification to
alleviate for the decrease DMI and milk production during heat
exposure in lactating dairy cows.
Abstract: In this paper a comprehensive model of a fossil fueled
power plant (FFPP) is developed in order to evaluate the
performance of a newly designed turbine follower controller.
Considering the drawbacks of previous works, an overall model is
developed to minimize the error between each subsystem model
output and the experimental data obtained at the actual power plant.
The developed model is organized in two main subsystems namely;
Boiler and Turbine. Considering each FFPP subsystem
characteristics, different modeling approaches are developed. For
economizer, evaporator, superheater and reheater, first order models
are determined based on principles of mass and energy conservation.
Simulations verify the accuracy of the developed models. Due to the
nonlinear characteristics of attemperator, a new model, based on a
genetic-fuzzy systems utilizing Pittsburgh approach is developed
showing a promising performance vis-à-vis those derived with other
methods like ANFIS. The optimization constraints are handled
utilizing penalty functions. The effect of increasing the number of
rules and membership functions on the performance of the proposed
model is also studied and evaluated. The turbine model is developed
based on the equation of adiabatic expansion. Parameters of all
evaluated models are tuned by means of evolutionary algorithms.
Based on the developed model a fuzzy PI controller is developed. It
is then successfully implemented in the turbine follower control
strategy of the plant. In this control strategy instead of keeping
control parameters constant, they are adjusted on-line with regard to
the error and the error rate. It is shown that the response of the
system improves significantly. It is also shown that fuel consumption
decreases considerably.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: Need for an appropriate system of evaluating students-
educational developments is a key problem to achieve the predefined
educational goals. Intensity of the related papers in the last years; that
tries to proof or disproof the necessity and adequacy of the students
assessment; is the corroborator of this matter. Some of these studies
tried to increase the precision of determining question weights in
scientific examinations. But in all of them there has been an attempt
to adjust the initial question weights while the accuracy and precision
of those initial question weights are still under question. Thus In
order to increase the precision of the assessment process of students-
educational development, the present study tries to propose a new
method for determining the initial question weights by considering
the factors of questions like: difficulty, importance and complexity;
and implementing a combined method of PROMETHEE and fuzzy
analytic network process using a data mining approach to improve
the model-s inputs. The result of the implemented case study proves
the development of performance and precision of the proposed
model.
Abstract: An integrated vehicle dynamics control system is developed in this paper by a combination of active front steering (AFS) and direct yaw-moment control (DYC) based on fuzzy logic control. The control system has a hierarchical structure consisting of two layers. A fuzzy logic controller is used in the upper layer (yaw rate controller) to keep the yaw rate in its desired value. The yaw rate error and its rate of change are applied to the upper controlling layer as inputs, where the direct yaw moment control signal and the steering angle correction of the front wheels are the outputs. In the lower layer (fuzzy integrator), a fuzzy logic controller is designed based on the working region of the lateral tire forces. Depending on the directions of the lateral forces at the front wheels, a switching function is activated to adjust the scaling factor of the fuzzy logic controller. Using a nonlinear seven degrees of freedom vehicle model, the simulation results illustrate considerable improvements which are achieved in vehicle handling through the integrated AFS/DYC control system in comparison with the individual AFS or DYC controllers.
Abstract: Complex assemblies of interacting proteins carry out
most of the interesting jobs in a cell, such as metabolism, DNA
synthesis, mitosis and cell division. These physiological properties
play out as a subtle molecular dance, choreographed by underlying
regulatory networks that control the activities of cyclin-dependent
kinases (CDK). The network can be modeled by a set of nonlinear
differential equations and its behavior predicted by numerical
simulation. In this paper, an innovative approach has been proposed
that uses genetic algorithms to mine a set of behavior data output by
a biological system in order to determine the kinetic parameters of
the system. In our approach, the machine learning method is
integrated with the framework of existent biological information in a
wiring diagram so that its findings are expressed in a form of system
dynamic behavior. By numerical simulations it has been illustrated
that the model is consistent with experiments and successfully shown
that such application of genetic algorithms will highly improve the
performance of mathematical model of the cell division cycle to
simulate such a complicated bio-system.
Abstract: In this paper an algorithm based on the adaptive
neuro-fuzzy controller is provided to enhance the tipover stability of
mobile manipulators when they are subjected to predefined
trajectories for the end-effector and the vehicle. The controller
creates proper configurations for the manipulator to prevent the robot
from being overturned. The optimal configuration and thus the most
favorable control are obtained through soft computing approaches
including a combination of genetic algorithm, neural networks, and
fuzzy logic. The proposed algorithm, in this paper, is that a look-up
table is designed by employing the obtained values from the genetic
algorithm in order to minimize the performance index and by using
this data base, rule bases are designed for the ANFIS controller and
will be exerted on the actuators to enhance the tipover stability of the
mobile manipulator. A numerical example is presented to
demonstrate the effectiveness of the proposed algorithm.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.
Abstract: There are three distinct stages in the evolution of
economic thought, namely:
1. in the first stage, the major concern was to accelerate
economic growth with increased availability of material
goods, especially in developing economies with very low
living standards, because poverty eradication meant faster
economic growth.
2. in the second stage, economists made distinction between
growth and development. Development was seen as going
beyond economic growth, and bringing certain changes in
the structure of the economy with more equitable
distribution of the benefits of growth, with the growth
coming automatic and sustained.
3. the third stage is now reached. Our concern is now with
“sustainable development", that is, development not only
for the present but also of the future.
Thus the focus changed from “sustained growth" to “sustained
development". Sustained development brings to the fore the long
term relationship between the ecology and economic development.
Since the creation of UNEP in 1972 it has worked for
development without destruction for environmentally sound and
sustained development. It was realised that the environment cannot
be viewed in a vaccum, it is not separate from development, nor is it
competing. It suggested for the integration of the environment with
development whereby ecological factors enter development planning,
socio-economic policies, cost-benefit analysis, trade, technology
transfer, waste management, educational and other specific areas.
Industrialisation has contributed to the growth of economy of
several countries. It has improved the standards of living of its people
and provided benefits to the society. It has also created in the process
great environmental problems like climate change, forest destruction
and denudation, soil erosion and desertification etc.
On the other hand, industry has provided jobs and improved the
prospects of wealth for the industrialists. The working class
communities had to simply put up with the high levels of pollution in
order to keep up their jobs and also to save their income.
There are many roots of the environmental problem. They may be
political, economic, cultural and technological conditions of the
modern society. The experts concede that industrial growth lies
somewhere close to the heart of the matter. Therefore, the objective
of this paper is not to document all roots of an environmental crisis
but rather to discuss the effects of industrial growth and
development.
We have come to the conclusion that although public intervention
is often unnecessary to ensure that perfectly competitive markets will
function in society-s best interests, such intervention is necessary
when firms or consumers pollute.
Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.
Abstract: This paper describes a new supervised fusion (hybrid)
electrocardiogram (ECG) classification solution consisting of a new
QRS complex geometrical feature extraction as well as a new version
of the learning vector quantization (LVQ) classification algorithm
aimed for overcoming the stability-plasticity dilemma. Toward this
objective, after detection and delineation of the major events of ECG
signal via an appropriate algorithm, each QRS region and also its
corresponding discrete wavelet transform (DWT) are supposed as
virtual images and each of them is divided into eight polar sectors.
Then, the curve length of each excerpted segment is calculated
and is used as the element of the feature space. To increase the
robustness of the proposed classification algorithm versus noise,
artifacts and arrhythmic outliers, a fusion structure consisting of
five different classifiers namely as Support Vector Machine (SVM),
Modified Learning Vector Quantization (MLVQ) and three Multi
Layer Perceptron-Back Propagation (MLP–BP) neural networks with
different topologies were designed and implemented. The new proposed
algorithm was applied to all 48 MIT–BIH Arrhythmia Database
records (within–record analysis) and the discrimination power of the
classifier in isolation of different beat types of each record was
assessed and as the result, the average accuracy value Acc=98.51%
was obtained. Also, the proposed method was applied to 6 number
of arrhythmias (Normal, LBBB, RBBB, PVC, APB, PB) belonging
to 20 different records of the aforementioned database (between–
record analysis) and the average value of Acc=95.6% was achieved.
To evaluate performance quality of the new proposed hybrid learning
machine, the obtained results were compared with similar peer–
reviewed studies in this area.
Abstract: Using plug flow model in conjunction with
experimental solute concentration profiles, overall volumetric mass
transfer coefficient based on continuous phase (Koca), in a packed
liquid-liquid extraction column has been optimized. Number of 12
experiments has been done using standard system of water/acid
acetic/toluene in a 6 cm diameter, 120 cm height column. Thorough
consideration of influencing parameters we intended to correlate
dimensionless parameters in term of overall Sherwood number which
has an acceptable average error of about 15.8%.
Abstract: This study aims at investigating the empirical
relationships between risk preference, internet preference, and
internet knowledge which are known as user characteristics, in
addition to perceived risk of the customers on the internet purchase
intention. In order to test the relationships between the variables of
model 174, a questionnaire was collected from the students with
previous online experience. For the purpose of data analysis,
confirmatory factor analysis (CFA) and structural equation model
(SEM) was used.
Test results show that the perceived risk affects the internet
purchase intention, and increase or decrease of perceived risk
influences the purchase intention when the customer does the internet
shopping. Other factors such as internet preference, knowledge of the
internet, and risk preference affect the internet purchase intention.