Abstract: In this study, we are interested in the economic lot
scheduling problem (ELSP) that considers manufacturing of the
serviceable products and remanufacturing of the reworked products. In
this paper, we formulate a mathematical model for the ELSP with
reworks using the basic period approach. In order to solve this
problem, we propose a search algorithm to find the cyclic multiplier ki
of each product that can be cyclically produced for every ki basic
periods. This research also uses two heuristics to search for the optimal
production sequence of all lots and the optimal time length of the basic
period so as to minimize the average total cost. This research uses a
numerical example to show the effectiveness of our approach.
Abstract: Clearance in the joints of multibody mechanical
systems such as linkage mechanisms and robots is a main source of
vibration, and noise of the whole system, and wear of the joints
themselves. This clearance is an inevitable matter and cannot be
eliminated, since it allows the relative motion between joint
components and make them assemblage. This paper presents an
experimental verification of the obtained simulation results of a slider
– crank mechanism of one clearance revolute joint. The simulation
results are obtained with the aid of CAD and dynamic simulation
softwares, which is an effective method of simulation multibody
systems with clearance joints and have many advantages. The
comparison between both simulation and experimental results shows
that the simulation results are so close to the experimental ones which
proves the accuracy and efficiency of this method of modeling and
simulation of mechanical systems with clearance joints.
Abstract: The groundwater is one of the main sources for
sustainability in the United Arab Emirates (UAE). Intensive
developments in Al-Ain area lead to increase water demand, which
consequently reduced the overall groundwater quantity in major
aquifers. However, in certain residential areas within Al-Ain, it has
been noticed that the groundwater level is rising, for example in
Sha-ab Al Askher area. The reasons for the groundwater rising
phenomenon are yet to be investigated. In this work, twenty four
seismic refraction profiles have been carried out along the study
pilot area; as well as field measurement of the groundwater level in
a number of available water wells in the area. The processed
seismic data indicated the deepest and shallowest groundwater
levels are 15m and 2.3 meters respectively. This result is greatly
consistent with the proper field measurement of the groundwater
level. The minimum detected value may be referred to perched
subsurface water which may be associated to the infiltration from
the surrounding water bodies such as lakes, and elevated farms. The
maximum values indicate the accurate groundwater level within the
study area. The findings of this work may be considered as a
preliminary help to the decision makers.
Abstract: Theoptimal extraction condition of dried Phaseolus
vulgaris powderwas studied. The three independent variables are raw
material concentration, shaking and centrifugaltime. The dependent
variables are both yield percentage of crude extract and alphaamylase
enzyme inhibition activity. The experimental design was
based on box-behnkendesign. Highest yield percentage of crude
extract could get from extraction condition at concentration of 1, 0,1,
concentration of 0.15 M ,extraction time for 2hour, and
separationtime for60 min. Moreover, the crude extract with highest
alpha-amylase enzyme inhibition activityoccurred by extraction
condition at concentration of 0.10 M, extraction time for 2 min, and
separation time for 45 min
Abstract: We propose a low-cost uniform analysis framework
allowing comparison of the strengths and weaknesses of the
bicycling experience within and between cities. A primary
component is an expedient, one-page mobility survey from which
mode share is calculated. The bicycle mode share of many cities
remains unknown, creating a serious barrier for both scientists and
policy makers aiming to understand and increase rates of bicycling.
Because of its low cost and expedience, this framework could be
replicated widely, uniformly filling the data gap. The framework has
been applied to 13 Central European cities with success. Data is
collected on multiple modes with specific questions regarding both
behavior and quality of travel experience. Individual preferences are
also collected, examining the conditions under which respondents
would change behavior to adopt more sustainable modes (bicycling
or public transportation). A broad analysis opportunity results,
intended to inform policy choices.
Abstract: The vehicle fleet of public transportation companies is often equipped with intelligent on-board passenger information systems. A frequently used but time and labor-intensive way for keeping the on-board controllers up-to-date is the manual update using different memory cards (e.g. flash cards) or portable computers. This paper describes a compression algorithm that enables data transmission using low bandwidth wireless radio networks (e.g. GPRS) by minimizing the amount of data traffic. In typical cases it reaches a compression rate of an order of magnitude better than that of the general purpose compressors. Compressed data can be easily expanded by the low-performance controllers, too.
Abstract: In this article we propose to model Net-banking
system by game theory. We adopt extensive game to model our web
application. We present the model in term of players and strategy.
We present UML diagram related the protocol game.
Abstract: It has been recognized that due to the autonomy and
heterogeneity, of Web services and the Web itself, new approaches
should be developed to describe and advertise Web services. The
most notable approaches rely on the description of Web services
using semantics. This new breed of Web services, termed semantic
Web services, will enable the automatic annotation, advertisement,
discovery, selection, composition, and execution of interorganization
business logic, making the Internet become a common
global platform where organizations and individuals communicate
with each other to carry out various commercial activities and to
provide value-added services. This paper deals with two of the
hottest R&D and technology areas currently associated with the Web
– Web services and the semantic Web. It describes how semantic
Web services extend Web services as the semantic Web improves the
current Web, and presents three different conceptual approaches to
deploying semantic Web services, namely, WSDL-S, OWL-S, and
WSMO.
Abstract: This paper presents a new methodology to study power and energy consumption in mechatronic systems early in the development process. This new approach makes use of two modeling languages to represent and simulate embedded control software and electromechanical subsystems in the discrete event and continuous time domain respectively within a single co-model. This co-model enables an accurate representation of power and energy consumption and facilitates the analysis and development of both software and electro-mechanical subsystems in parallel. This makes the engineers aware of energy-wise implications of different design alternatives and enables early trade-off analysis from the beginning of the analysis and design activities.
Abstract: This research aimed at investigating the Cr (III), Cd
(II) and Pb (II) removal efficiencies by using the newly synthesized
metal oxides/ polyethersulfone (PES), Al2O3/PES and ZrO2/PES,
membranes from synthetic wastewater and exploring fouling
mechanisms. A Comparative study between the removal efficiencies
of Cr (III), Cd (II) and Pb (II) from synthetic and natural wastewater
by using adsorption onto agricultural by products and the newly
synthesized Al2O3/PES and ZrO2/PES membranes was conducted to
assess the advantages and limitations of using the metal oxides/PES
membranes for heavy metals removal. The results showed that about
99 % and 88 % removal efficiencies were achieved by the tested
membranes for Pb (II) and Cr (III), respectively.
Abstract: Service trade is an important force of influencing economic development. A review on the related literatures is done firstly. Then through the construction of a Diamond Model, the main factors which influence the competitiveness of Chinese service trade are determined. With three competitiveness indexes served as the reference series respectively, the influencing factors served as the comparable series, three grey incidence models are then built up to conduct an empirical analysis on the main factors influencing the competitiveness of service trade after China entering WTO. The result indicates that urbanization level, open degree of service industry and foreign direct investment have larger impacts on Chinese service trade competitiveness, followed in turn by GDP in service industry and human capital, while commodity trade has the minimum impact. Further discussion provides train of thought for the upgrade of Chinese service trade competitiveness.
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: A numerical method for solving nonlinear Fredholm integral equations of second kind is proposed. The Fredholm type equations which have many applications in mathematical physics are then considered. The method is based on hybrid function approximations. The properties of hybrid of block-pulse functions and Chebyshev polynomials are presented and are utilized to reduce the computation of nonlinear Fredholm integral equations to a system of nonlinear. Some numerical examples are selected to illustrate the effectiveness and simplicity of the method.
Abstract: XML data consists of a very flexible tree-structure
which makes it difficult to support the storing and retrieving of XML
data. The node numbering scheme is one of the most popular
approaches to store XML in relational databases. Together with the
node numbering storage scheme, structural joins can be used to
efficiently process the hierarchical relationships in XML. However, in
order to process a tree-structured XPath query containing several
hierarchical relationships and conditional sentences on XML data,
many structural joins need to be carried out, which results in a high
query execution cost. This paper introduces mechanisms to reduce the
XPath queries including branch nodes into a much more efficient form
with less numbers of structural joins. A two step approach is proposed.
The first step merges duplicate nodes in the tree-structured query and
the second step divides the query into sub-queries, shortens the paths
and then merges the sub-queries back together. The proposed
approach can highly contribute to the efficient execution of XML
queries. Experimental results show that the proposed scheme can
reduce the query execution cost by up to an order of magnitude of the
original execution cost.
Abstract: We study the possibility of using geometric operators
in the selection of human resources. We develop three new methods
that use the ordered weighted geometric (OWG) operator in different
indexes used for the selection of human resources. The objective of
these models is to manipulate the neutrality of the old methods so the
decision maker is able to select human resources according to his
particular attitude. In order to develop these models, first a short
revision of the OWG operator is developed. Second, we briefly
explain the general process for the selection of human resources.
Then, we develop the three new indexes. They will use the OWG
operator in the Hamming distance, in the adequacy coefficient and in
the index of maximum and minimum level. Finally, an illustrative
example about the new approach is given.
Abstract: In this paper, the vessel inscribed trigonometry (VITM) for the vessel progression orientation (VPO) is proposed in the two-dimensional fundus image. The VPO is a major factor in the optic disc (OD) detection which is a basic process in the retina analysis. To measure the VPO, skeletons of vessel are used. First, the vessels are classified into three classes as vessel end, vessel branch and vessel stem. And the chain code maps of VS are generated. Next, two farthest neighborhoods of each point on VS are searched by the proposed angle restriction. Lastly, a gradient of the straight line between two farthest neighborhoods is estimated to measure the VPO. VITM is validated by comparing with manual results and 2D Gaussian templates. It is confirmed that VPO of the proposed mensuration is correct enough to detect OD from the results of experiment which applied VITM to detect OD in fundus images.
Abstract: The increasing development of wireless networks and
the widespread popularity of handheld devices such as Personal
Digital Assistants (PDAs), mobile phones and wireless tablets
represents an incredible opportunity to enable mobile devices as a
universal payment method, involving daily financial transactions.
Unfortunately, some issues hampering the widespread acceptance of
mobile payment such as accountability properties, privacy protection,
limitation of wireless network and mobile device. Recently, many
public-key cryptography based mobile payment protocol have been
proposed. However, limited capabilities of mobile devices and
wireless networks make these protocols are unsuitable for mobile
network. Moreover, these protocols were designed to preserve
traditional flow of payment data, which is vulnerable to attack and
increase the user-s risk. In this paper, we propose a private mobile
payment protocol which based on client centric model and by
employing symmetric key operations. The proposed mobile payment
protocol not only minimizes the computational operations and
communication passes between the engaging parties, but also
achieves a completely privacy protection for the payer. The future
work will concentrate on improving the verification solution to
support mobile user authentication and authorization for mobile
payment transactions.
Abstract: Knowledge is a key asset for any organisation to
sustain competitive advantages, but it is difficult to identify and
represent knowledge which is needed to perform activities in
business processes. The effective knowledge management and
support for relevant business activities definitely gives a huge impact
to the performance of the organisation as a whole. This is because
that knowledge have the functions of directing, coordinating and
controlling actions within business processes. The study has
introduced organisational morphology, a norm-based approach by
applying semiotic theories which emphasise on the representation of
knowledge in norms. This approach is concerned with the
identification of activities into three categories: substantive,
communication and control activities. All activities are directed by
norms; hence three types of norms exist; each is associated to a
category of activities. The paper describes the approach briefly and
illustrates the application of this approach through a case study of
academic activities in higher education institutions. The result of the
study shows that the approach provides an effective way to profile
business knowledge and the profile enables the understanding and
specification of business requirements of an organisation.
Abstract: A first intermediate roll of Sendzirmir mills was failure
by surface spalling during operation. After analyzing by visual, stereo
microscope, optical microscope, scanning electron microscope,
glow-discharged spectrometer and hardness test, respectively, the
results show that some voids and cracks existed on the contact surface
as well as subsurface. Further examination verified inadequate
hardness and inclusions were responsible for the failure of surface
spalling.
Abstract: Nonspecific protein adsorption generally occurs on
any solid surfaces and usually has adverse consequences. Adsorption
of proteins onto a solid surface is believed to be the initial and
controlling step in biofouling. Surfaces modified with end-tethered
poly(ethylene glycol) (PEG) have been shown to be protein-resistant
to some degree. In this study, the adsorption of β-casein and
lysozyme was performed on 6 different types of surfaces where PEG
was tethered onto stainless steel by polyethylene imine (PEI) through
either OH or NHS end groups. Protein adsorption was also performed
on the bare stainless steel surface as a control. The adsorption was
conducted at 23 °C and pH 7.2. In situ QCM-D was used to
determine PEG adsorption kinetics, plateau PEG chain densities,
protein adsorption kinetics and plateau protein adsorbed quantities.
PEG grafting density was the highest for a NHS coupled chain,
around 0.5 chains / nm2. Interestingly, lysozyme which has smaller
size than β-casein, appeared to adsorb much less mass than that of β-
casein. Overall, the surface with high PEG grafting density exhibited
a good protein rejection.