Abstract: Nitrogen-doped graphene quantum dots (N-GQDs)
were fabricated by microwave-assisted hydrothermal technique. The
optical properties of the N-GQDs were studied. The luminescence of
the N-GQDs can be tuned by varying the excitation wavelength.
Furthermore, two-photon luminescence of the N-GQDs excited by
near-infrared laser can be obtained. It is shown that N-doping play a
key role on two-photon luminescence. The N-GQDs are expected to
find application in biological applications including bioimaging and
sensing.
Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: In the cloud computing hierarchy IaaS is the lowest
layer, all other layers are built over it. Thus it is the most important
layer of cloud and requisite more importance. Along with advantages
IaaS faces some serious security related issue. Mainly Security
focuses on Integrity, confidentiality and availability. Cloud
computing facilitate to share the resources inside as well as outside of
the cloud. On the other hand, cloud still not in the state to provide
surety to 100% data security. Cloud provider must ensure that end
user/client get a Quality of Service. In this report we describe
possible aspects of cloud related security.
Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.
Abstract: In a highly competitive environment, it becomes more
important to shorten the whole business process while delivering or
even enhancing the business value to the customers and suppliers.
Although the workflow management systems receive much attention
for its capacity to practically support the business process enactment,
the effective workflow modeling method remain still challenging and
the high degree of process complexity makes it more difficult to gain
the short lead time. This paper presents a workflow structuring method
in a holistic way that can reduce the process complexity using
activity-needs and formal concept analysis, which eventually enhances
the key performance such as quality, delivery, and cost in business
process.
Abstract: The efficiency of wood vinegar mixed with each
individual of three plants extract such as: citronella grass
(Cymbopogon nardus), neem seed (Azadirachta indica A. Juss), and
yam bean seed (Pachyrhizus erosus Urb.) were tested against the
second instar larvae of housefly (Musca domestica L.). Steam
distillation was used for extraction of the citronella grass while neem
and yam bean were simple extracted by fermentation with ethyl
alcohol. Toxicity test was evaluated in laboratory based on two
methods of larvicidal bioassay: topical application method (contact
poison) and feeding method (stomach poison). Larval mortality was
observed daily and larval survivability was recorded until the
survived larvae developed to pupae and adults. The study resulted
that treatment of wood vinegar mixed with citronella grass showed
the highest larval mortality by topical application method (50.0%)
and by feeding method (80.0%). However, treatment of mixed wood
vinegar and neem seed showed the longest pupal duration to 25 day
and 32 days for topical application method and feeding method
respectively. Additional, larval duration on treated M. domestica
larvae was extended to 13 days for topical application method and 11
days for feeding method. Thus, the feeding method gave higher
efficiency compared with the topical application method.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: The operation of nuclear power plants involves
continuous monitoring of the environment in their area. This
monitoring is performed using a complex data acquisition system,
which collects status information about the system itself and values
of many important physical variables e.g. temperature, humidity,
dose rate etc. This paper describes a proposal and optimization of
communication that takes place in teledosimetric system between the
central control server responsible for the data processing and storing
and the decentralized measuring stations, which are measuring the
physical variables. Analyzes of ongoing communication were
performed and consequently the optimization of the system
architecture and communication was done.
Abstract: Quality control helps industries in improvements of its
product quality and productivity. Statistical Process Control (SPC) is
one of the tools to control the quality of products that turning practice
in bringing a department of industrial engineering process under
control. In this research, the process control of a turning
manufactured at workshops machines. The varying measurements
have been recorded for a number of samples of a rice polished
cylinder obtained from a number of trials with the turning practice.
SPC technique has been adopted by the process is finally brought
under control and process capability is improved.
Abstract: Due to growing concern about environmental and
social consequences throughout the world, a need has been felt to
incorporate sustainability concepts in conventional manufacturing.
This paper is an attempt to identify and evaluate drivers in
implementing sustainable manufacturing in Indian context. Nine
possible drivers for successful implementation of sustainable
manufacturing have been identified from extensive review. Further,
Decision Making Trial and Evaluation Laboratory (DEMATEL)
approach has been utilized to evaluate and categorize these identified
drivers for implementing sustainable manufacturing in to the cause
and effect groups. Five drivers (Societal Pressure and Public
Concerns; Regulations and Government Policies; Top Management
Involvement, Commitment and Support; Effective Strategies and
Activities towards Socially Responsible Manufacturing and Market
Trends) have been categorized into the cause group and four drivers
(Holistic View in Manufacturing Systems; Supplier Participation;
Building Sustainable culture in Organization; and Corporate Image
and Benefits) have been categorized into the effect group. “Societal
Pressure and Public Concerns” has been found the most critical driver
and “Corporate Image and Benefits” as least critical or the most
easily influenced driver to implementing sustainable manufacturing
in Indian context. This paper may surely help practitioners in better
understanding of these drivers and their priorities towards effective
implementation of sustainable manufacturing.
Abstract: Nanostructured catalysts were successfully prepared
by acidification of diatomite and regeneration of FCC spent catalysts.
The obtained samples were characterized by IR, XRD, SEM, EDX,
MAS-NMR (27Al and 29Si), NH3-TPD and tested in catalytic
pyrolysis of biomass (rice straw). The results showed that the similar
bio-oil yield of 41.4% can be obtained by pyrolysis with catalysts at
450oC as compared to that of the pyrolysis without catalyst at 550oC.
The bio-oil yield reached a maximum of 42.55% at the pyrolysis
temperature of 500oC with catalytic content of 20%. Moreover, by
catalytic pyrolysis, bio-oil quality was better as reflected in higher
ratio of H/C, lower ratio of O/C. This clearly indicated high
application potential of these new nanostructured catalysts in the
production of bio-oil with low oxygenated compounds.
Abstract: The influence of three different types of halloysite
nanotubes (HNTs) with different dimensions, namely as camel lake
(CLA), Jarrahdale (JA) and Matauri Bay (MB), on their reinforcing
ability of ethylene propylene dine monomer (EPDM) were
investigated by varying the HNTs loading (from 0-15 phr).
Mechanical properties of the nanocomposites improved with addition
of all three HNTs, but CLA based nanocomposites exhibited a
significant enhancement compared to the other HNTs. For instance,
tensile properties of EPDM nanocomposites increased by 120%,
256% and 340% for MB, JA and CLA, respectively, with addition of
15 phr of HNTs. This could be due to the higher aspect ratio and
higher surface area of CLA compared to others. Scanning electron
microscopy (SEM) of nanocomposites at 15 phr of HNT loadings
showed low amounts of pulled-out nanotubes which confirmed the
presence of more embedded nanotubes inside the EPDM matrix, as
well as aggregates within the fracture surface of EPDM/HNT
nanocomposites
Abstract: This paper discusses the potential benefits of an
interactive multimedia information representation in enhancing
students’ critical thinking aligned with history reasoning in learning
history amongst Secondary School students in Malaysia. Two modes
of multimedia information representation were implemented;
chronologic and thematic information representations. A qualitative
study of an unstructured interview was conducted among two history
teachers, one history education lecturer, two i-think experts, and five
students from Form Four secondary school. The interview was to
elicit their opinions on the implementation of thinking maps and
interactive multimedia information representation in history learning.
The key elements of the interactive multimedia (e.g. multiple media,
user control, interactivity and use of timelines and concept maps)
were then considered to improve the learning process. Findings of the
preliminary investigation reveal that the interactive multimedia
information representations have the potential benefits to be
implemented as an instructional resource in enhancing students’
higher order thinking skills (HOTs). This paper concludes by giving
suggestions for future work.
Abstract: India holds 17.5% of the world’s population but has
only 2% of the total geographical area of the world where 27.35% of
the area is categorized as wasteland due to lack of or less
groundwater. So there is a demand for excessive groundwater for
agricultural and non agricultural activities to balance its growth rate.
With this in mind, an attempt is made to find the groundwater
potential zone in Gomukhi Nadhi sub basin of Vellar River basin,
TamilNadu, India covering an area of 1146.6 Sq.Km consists of 9
blocks from Peddanaickanpalayam to Virudhachalam in the sub
basin. The thematic maps such as Geology, Geomorphology,
Lineament, Landuse and Landcover and Drainage are prepared for
the study area using IRS P6 data. The collateral data includes rainfall,
water level, soil map are collected for analysis and inference. The
digital elevation model (DEM) is generated using Shuttle Radar
Topographic Mission (SRTM) and the slope of the study area is
obtained. ArcGIS 10.1 acts as a powerful spatial analysis tool to find
out the ground water potential zones in the study area by means of
weighted overlay analysis. Each individual parameter of the thematic
maps are ranked and weighted in accordance with their influence to
increase the water level in the ground. The potential zones in the
study area are classified viz., Very Good, Good, Moderate, Poor with
its aerial extent of 15.67, 381.06, 575.38, 174.49 Sq.Km respectively.
Abstract: Musculoskeletal injuries in school children could be
reduced improving trunk strength and hamstring flexibility. Low
levels of trunk muscle strength and hamstring flexibility may result in
acute and musculoskeletal chronic diseases. The Pilates Method can
be appropriate to improve these physical condition attributes and has
been rarely employed by this social group. On the other hand, it has
been shown that trunk strength and flexibility are different between
genders, but there is no evidence about the effect of exercise
programs designed to improve both items in school children.
Therefore the objective of this study was to measure the effect of a
six-week Pilates-based exercise program in 14 year old school
children trunk strength and hamstring flexibility, establishing
differences in gender. The sample was composed of 57 students
divided into experimental group (EG; n=30) and control group (CG;
n=27). Bench Trunk Curl test (BTC), Sörensen test and Toe-touch
test (TT) were used to measure dynamic muscular resistance in trunk
flexion, isometric strength in trunk extension and hamstring
flexibility, respectively. EG utilized the Pilates exercise program
during six-weeks (2 days/week, 55minutes/session). After this period
of training, EG improved trunk strength and hamstring flexibility
significantly but there were no significant differences within CG.
Although boys were better in BTC test and girls were better in TT
test, there were no significant differences between them.
Abstract: Taro Scarab beetles (Papuana uninodis, Coleoptera:
Scarabaeidae) inflict severe damage on important root crops and
plants such as Taro or Cocoyam, yam, sweet potatoes, oil palm and
coffee tea plants across Africa and Asia resulting in economic
hardship and starvation in some nations. Scoliid wasps and
Metarhizium anisopliae fungus - bio-control agents; are shown to be
able to control the population of Scarab beetle adults and larvae using
a newly created simulation model based on non-linear ordinary
differential equations that track the populations of the beetle life
cycle stages: egg, larva, pupa, adult and the population of the scoliid
parasitoid wasps, which attack beetle larvae. In spite of the challenge
driven by the longevity of the scarab beetles, the combined effect of
the larval wasps and the fungal bio-control agent is able to control
and drive down the population of both the adult and the beetle eggs
below the environmental carrying capacity within an interval of 120
days, offering the long term prospect of a stable and eco-friendly
environment; where the population of scarab beetles is: regulated by
parasitoid wasps and beneficial soil saprophytes.
Abstract: Energy consumption and users’ satisfaction were
compared in three LEED certified office buildings in turkey and an
office building in Egypt. The field studies were conducted in summer
2012. The measured environmental parameters in the four buildings
were indoor air temperature, relative humidity, CO2 percentage and
light intensity. The traditional building is located in Smart Village in
Abu Rawash, Cairo, Egypt. The building was studied for 7 days
resulting in 84 responds. The three rated buildings are in Istanbul;
Turkey. A Platinum LEED certified office building is owned by
BASF and gained a platinum certificate for new construction and
major renovation. The building was studied for 3 days resulting in 13
responds. A Gold LEED certified office building is owned by BASF
and gained a gold certificate for new construction and major
renovation. The building was studied for 2 days resulting in 10
responds. A silver LEED certified office building is owned by
Unilever and gained a silver certificate for commercial interiors. The
building was studied for 7 days resulting in 84 responds.
The results showed that all buildings had no significant difference
regarding occupants’ satisfaction with the amount of lighting, noise
level, odor and access to the outdoor view. There was significant
difference between occupants’ satisfaction in LEED certified
buildings and the traditional building regarding the thermal
environment and the perception of the general environment (colors,
carpet and decoration. The findings suggest that careful design could
lead to a certified building that enhances the thermal environment and
the perception of the indoor environment leading to energy
consumption without scarifying occupants’ satisfaction.
Abstract: The aim of the present work was to statistically design
an autotrophic medium for maximum biomass production by
Chlorella pyrenoidosa using response surface methodology. After
evaluating one factor at a time approach, K2HPO4, KNO3,
MgSO4.7H2O and NaHCO3 were preferred over the other
components of the fog’s medium as most critical autotrophic medium
components. The study showed that the maximum biomass yield was
achieved while the concentrations of MgSO4.7H2O, K2HPO4, KNO3
and NaHCO3 were 0.409 g/L, 0.24 g/L, 1.033 g/L, and 3.265 g/L,
respectively. The study reported that the biomass productivity of C.
pyrenoidosa improved from 0.14 g/L in defined fog’s medium to 1.40
g/L in modified fog’s medium resulting 10 fold increase. The
biochemical composition biosynthesis of C. pyrenoidosa was altered
using nitrogen limiting stress bringing about 5.23 fold increase in
lipid content than control (cell without stress), as analyzed by FTIR
integration method.
Abstract: Software reusability is an essential characteristic of
Component-Based Software (CBS). The component reusability is an
important assess for the effective reuse of components in CBS. The
attributes of reusability proposed by various researchers are studied
and four of them are identified as potential factors affecting
reusability. This paper proposes metric for reusability estimation of
black-box software component along with metrics for Interface
Complexity, Understandability, Customizability and Reliability. An
experiment is performed for estimation of reusability through a case
study on a sample web application using a real world component.
Abstract: Distributed Generation (DG) can help in reducing the
cost of electricity to the costumer, relieve network congestion and
provide environmentally friendly energy close to load centers. Its
capacity is also scalable and it provides voltage support at distribution
level. Hence, DG placement and penetration level is an important
problem for both the utility and DG owner. DG allocation and capacity
determination is a nonlinear optimization problem. The objective
function of this problem is the minimization of the total loss of the
distribution system. Also high levels of penetration of DG are a new
challenge for traditional electric power systems. This paper presents a
new methodology for the optimal placement of DG and penetration
level of DG in distribution system based on General Algebraic
Modeling System (GAMS) and Genetic Algorithm (GA).