Abstract: Fuzzy inference method based approach to the
forming of modular intellectual system of assessment the quality of
communication services is proposed. Developed under this approach
the basic fuzzy estimation model takes into account the
recommendations of the International Telecommunication Union in
respect of the operation of packet switching networks based on IPprotocol.
To implement the main features and functions of the fuzzy
control system of quality telecommunication services it is used
multilayer feedforward neural network.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: Red blood cells (RBC) are the most common types of
blood cells and are the most intensively studied in cell biology. The
lack of RBCs is a condition in which the amount of hemoglobin level
is lower than normal and is referred to as “anemia”. Abnormalities in
RBCs will affect the exchange of oxygen. This paper presents a
comparative study for various techniques for classifying the RBCs as
normal or abnormal (anemic) using WEKA. WEKA is an open
source consists of different machine learning algorithms for data
mining applications. The algorithms tested are Radial Basis Function
neural network, Support vector machine, and K-Nearest Neighbors
algorithm. Two sets of combined features were utilized for
classification of blood cells images. The first set, exclusively consist
of geometrical features, was used to identify whether the tested blood
cell has a spherical shape or non-spherical cells. While the second
set, consist mainly of textural features was used to recognize the
types of the spherical cells. We have provided an evaluation based on
applying these classification methods to our RBCs image dataset
which were obtained from Serdang Hospital - Malaysia, and
measuring the accuracy of test results. The best achieved
classification rates are 97%, 98%, and 79% for Support vector
machines, Radial Basis Function neural network, and K-Nearest
Neighbors algorithm respectively.
Abstract: The classroom of the 21st century is an ever changing
forum for new and innovative thoughts and ideas. With increasing
technology and opportunity, students have rapid access to
information that only decades ago would have taken weeks to obtain.
Unfortunately, new techniques and technology are not the cure for
the fundamental problems that have plagued the classroom ever since
education was established. Class size has been an issue long debated
in academia. While it is difficult to pin point an exact number, it is
clear that in this case more does not mean better. By looking into the
success and pitfalls of classroom size the true advantages of smaller
classes will become clear. Previously, one class was comprised of 50
students. Being seventeen and eighteen- year- old students,
sometimes it was quite difficult for them to stay focused. To help
them understand and gain much knowledge, a researcher introduced
“The Theory of Multiple Intelligence” and this, in fact, enabled
students to learn according to their own learning preferences no
matter how they were being taught. In this lesson, the researcher
designed a cycle of learning activities involving all intelligences so
that everyone had equal opportunities to learn.
Abstract: Solar air heater is a type of heat exchanger which
transforms solar radiation into heat energy. The thermal performance
of conventional solar air heater has been found to be poor because of
the low convective heat transfer coefficient from the absorber plate to
the air. It is attributed to the formation of a very thin boundary layer
at the absorber plate surface commonly known as viscous sub-layer.
Thermal efficiency of solar air heater can be improved by providing
the artificial roughness on absorber plate is the most efficient
technique. In this paper an attempt is made to provide artificial
roughness by incorporating inclined multiple V-ribs in the underside
of the absorber plate. 60˚V – ribs are arranged inclined to the
direction of air flow. Performance of collector estimated theoretically
and experimentally. Results of the investigation reveal that thermal
efficiency of collector with multiple V-ribs increased by 14%.
Abstract: In this work, we propose and analyze a model of
Phytoplankton-Zooplankton interaction with harvesting considering
that some species are exploited commercially for food. Criteria for
local stability, instability and global stability are derived and some
threshold harvesting levels are explored to maintain the population
at an appropriate equilibrium level even if the species are exploited
continuously.Further,biological and bionomic equilibria of the system
are obtained and an optimal harvesting policy is also analysed using
the Pantryagin’s Maximum Principle.Finally analytical findings are
also supported by some numerical simulations.
Abstract: Now-a-days autonomous mobile robots have found
applications in diverse fields. An autonomous robot system must be
able to behave in an intelligent manner to deal with complex and
changing environment. This work proposes the performance of path
planning and navigation of autonomous mobile robot using
Gravitational Search Algorithm (GSA), Simulated Annealing (SA)
and Particle Swarm optimization (PSO) based intelligent controllers
in an unstructured environment. The approach not only finds a valid
collision free path but also optimal one. The main aim of the work is
to minimize the length of the path and duration of travel from a
starting point to a target while moving in an unknown environment
with obstacles without collision. Finally, a comparison is made
between the three controllers, it is found that the path length and time
duration made by the robot using GSA is better than SA and PSO
based controllers for the same work.
Abstract: Steganography is the art and science that hides the information in an appropriate cover carrier like image, text, audio and video media. In this work the authors propose a new image based steganographic method for hiding information within the complex bit planes of the image. After slicing into bit planes the cover image is analyzed to extract the most complex planes in decreasing order based on their bit plane complexity. The complexity function next determines the complex noisy blocks of the chosen bit plane and finally pixel mapping method (PMM) has been used to embed secret bits into those regions of the bit plane. The novel approach of using pixel mapping method (PMM) in bit plane domain adaptively embeds data on most complex regions of image, provides high embedding capacity, better imperceptibility and resistance to steganalysis attack.
Abstract: Heavy rare earth (HRE) oxalate concentrates were
prepared from the Egyptian crude monazite sand (graded about 47%).
The concentrates were specified quantitatively for their constituents
of individual rare earth elements using ion chromatograph (IC) and
qualitatively by scanning electron microscope (SEM) for the other
major constituents. The 1st concentrate was composed of 10.5%
HREE where 7.25% of them represented yttrium. The 2nd concentrate
contained about 41.7% LREE, 17.5% HREE and 13.6% Th. The
LREE involved 18.3% Ce, 10.5% La and 8% Nd while the HREE
were 8.7% Y, 3.5% Gd and 2.9% Dy. The 3rd concentrate was
containing about 8.0% LREE (3.7% Ce, 2.0% La and 1.5% Nd),
10.2% HREE (6.4% yttrium and 2.0% Dy) and 2.1% uranium. The
final concentrate comprised 0.84% uranium beside iron, chromium
and traces of REE.
Abstract: Many of the ever-growing elderly population require
exercise, such as running, for health management. One important
element of a runner’s training is the choice of shoes for exercise; shoes
are important because they provide the interface between the feet and
road. When we purchase shoes, we may instinctively choose a pair
after trying on many different pairs of shoes. Selecting the shoes
instinctively may work, but it does not guarantee a suitable fit for
running activities. Therefore, if we could select suitable shoes for each
runner from the viewpoint of brain activities, it would be helpful for
validating shoe selection. In this paper, we describe how brain
activities show different characteristics during particular task,
corresponding to different properties of shoes. Using five subjects, we
performed a verification experiment, applying weight, softness, and
flexibility as shoe properties. In order to affect the shoe property’s
differences to the brain, subjects run for 10 min. Before and after
running, subjects conducted a paced auditory serial addition task
(PASAT) as the particular task; and the subjects’ brain activities
during the PASAT are evaluated based on oxyhemoglobin and
deoxyhemoglobin relative concentration changes, measured by
near-infrared spectroscopy (NIRS). When the brain works actively,
oxihemoglobin and deoxyhemoglobin concentration drastically
changes; therefore, we calculate the maximum values of concentration
changes. In order to normalize relative concentration changes after
running, the maximum value are divided by before running maximum
value as evaluation parameters. The classification of the groups of
shoes is expressed on a self-organizing map (SOM). As a result,
deoxyhemoglobin can make clusters for two of the three types of
shoes.
Abstract: Reburning is a useful technology in reducing nitric
oxide through injection of a secondary hydrocarbon fuel. In this paper,
an experimental study has been conducted to evaluate the effect of fuel
lean reburning on NOx/CO reduction in LNG flame. Experiments
were performed in flames stabilized by a co-flow swirl burner, which
was mounted at the bottom of the furnace. Tests were conducted using
LNG gas as the reburn fuel as well as the main fuel. The effects of
reburn fuel fraction and injection manner of the reburn fuel were
studied when the fuel lean reburning system was applied. The paper
reports data on flue gas emissions and temperature distribution in the
furnace for a wide range of experimental conditions. At steady state,
temperature distribution and emission formation in the furnace have
been measured and compared. This paper makes clear that in order to
decrease both NOx and CO concentrations in the exhaust when the
pulsated fuel lean reburning system was adapted, it is important that
the control of some factors such as frequency and duty ratio. Also it
shows the fuel lean reburning is also effective method to reduce NOx
as much as reburning.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.
Abstract: In this paper a comprehensive review on various
factory layouts has been carried out for designing a lucrative process
layout for medium scale industries. Industry data base reveals that the
end product rejection rate is on the order of 10% amounting large
profit loss. In order to avoid these rejection rates and to increase the
quality product production an intermediate non-destructive testing
facility (INDTF) has been recommended for increasing the overall
profit. We observed through detailed case studies that while
introducing INDTF to medium scale industries the expensive
production process can be avoided to the defective products well
before its final shape. Additionally, the defective products identified
during the intermediate stage can be effectively utilized for other
applications or recycling; thereby the overall wastage of the raw
materials can be reduced and profit can be increased. We concluded
that the prudent design of a factory layout through critical path
method facilitating with INDTF will warrant profitable outcome.
Abstract: This paper investigates the joint effect of the
interconnected (n,k)-star network topology and Multi-Agent
automated control on restoration and reconfiguration of power
systems. With the increasing trend in development in Multi-Agent
control technologies applied to power system reconfiguration
in presence of faulty components or nodes. Fault tolerance is
becoming an important challenge in the design processes of the
distributed power system topology. Since the reconfiguration of a
power system is performed by agent communication, the (n,k)-star
interconnected network topology is studied and modeled in this
paper to optimize the process of power reconfiguration. In this paper,
we discuss the recently proposed (n,k)-star topology and examine its
properties and advantages as compared to the traditional multi-bus
power topologies. We design and simulate the topology model for
distributed power system test cases. A related lemma based on the
fault tolerance and conditional diagnosability properties is presented
and proved both theoretically and practically. The conclusion is
reached that (n,k)-star topology model has measurable advantages
compared to standard bus power systems while exhibiting fault
tolerance properties in power restoration, as well as showing
efficiency when applied to power system route discovery.
Abstract: This paper reports a structured literature review of the
application of Health Information Technology in developing
countries, defined as the World Bank categories Low-income
countries, Lower-middle-income, and Upper-middle-income
countries. The aim was to identify and classify the various
applications of health information technology to assess its current
state in developing countries and explore potential areas of research.
We offer specific analysis and application of HIT in Libya as one of
the developing countries. A structured literature review was
conducted using the following online databases: IEEE, Science
Direct, PubMed, and Google Scholar. Publication dates were set for
2000-2013. For the PubMed search, publications in English, French,
and Arabic were specified. Using a content analysis approach, 159
papers were analyzed and a total number of 26 factors were identified
that affect the adoption of health information technology. Of the 2681
retrieved articles, 159 met the inclusion criteria which were carefully
analyzed and classified. The implementation of health information
technology across developing countries is varied. Whilst it was
initially expected financial constraints would have severely limited
health information technology implementation, some developing
countries like India have nevertheless dominated the literature and
taken the lead in conducting scientific research. Comparing the
number of studies to the number of countries in each category, we
found that Low-income countries and Lower-middle-income had
more studies carried out than Upper-middle-income countries.
However, whilst IT has been used in various sectors of the economy,
the healthcare sector in developing countries is still failing to benefit
fully from the potential advantages that IT can offer.
Abstract: The investigation on wind turbine degradation was
carried out using the nacelle wind data. The three Vestas V80-2MW
wind turbines of Sungsan wind farm in Jeju Island, South Korea were
selected for this work. The SCADA data of the wind farm for five
years were analyzed to draw power curve of the turbines. It is assumed
that the wind distribution is the Rayleigh distribution to calculate the
normalized capacity factor based on the drawn power curve of the
three wind turbines for each year. The result showed that the reduction
of power output from the three wind turbines occurred every year and
the normalized capacity factor decreased to 0.12%/year on average.
Abstract: Ontologies offer a means for representing and sharing
information in many domains, particularly in complex domains. For
example, it can be used for representing and sharing information
of System Requirement Specification (SRS) of complex systems
like the SRS of ERTMS/ETCS written in natural language. Since
this system is a real-time and critical system, generic ontologies,
such as OWL and generic ERTMS ontologies provide minimal
support for modeling temporal information omnipresent in these SRS
documents. To support the modeling of temporal information, one
of the challenges is to enable representation of dynamic features
evolving in time within a generic ontology with a minimal redesign
of it. The separation of temporal information from other information
can help to predict system runtime operation and to properly design
and implement them. In addition, it is helpful to provide a reasoning
and querying techniques to reason and query temporal information
represented in the ontology in order to detect potential temporal
inconsistencies. To address this challenge, we propose a lightweight
3-layer temporal Quality of Service (QoS) ontology for representing,
reasoning and querying over temporal and non-temporal information
in a complex domain ontology. Representing QoS entities in separated
layers can clarify the distinction between the non QoS entities
and the QoS entities in an ontology. The upper generic layer of
the proposed ontology provides an intuitive knowledge of domain
components, specially ERTMS/ETCS components. The separation of
the intermediate QoS layer from the lower QoS layer allows us to
focus on specific QoS Characteristics, such as temporal or integrity
characteristics. In this paper, we focus on temporal information that
can be used to predict system runtime operation. To evaluate our
approach, an example of the proposed domain ontology for handover
operation, as well as a reasoning rule over temporal relations in this
domain-specific ontology, are presented.
Abstract: In wireless communication, space-time block code (STBC), cyclic delay diversity (CDD) and space-time cyclic delay diversity (STCDD)are used as the spatial diversity schemes and have been widely studied for the reliablecommunication. If these schemes are used, the communication system can obtain the improved performance. However,the quality of the system is degraded when the distance between a source and a destination is distant in wireless communication system. In this paper, the cooperative transmission scheme using two sources is proposed and improves the performance of the wireless communication system.
Abstract: Non-destructive testing and evaluation techniques for
assessing the integrity of composite structures are essential to both
reduce manufacturing costs and out of service time of transport means
due to maintenance. In this study, Analyze into non-destructive test
characterization of carbon fiber reinforced plastics (CFRP) internal
and external defects using thermo-graphic camera and transient
thermography method. non-destructive testing were characterized by
defect size (Ø8, Ø10, Ø12, Ø14) and depth (1.2mm, 2.4mm).
Abstract: Brown seaweeds are abundant in Portuguese coastline
and represent an almost unexploited marine economic resource. One
of the most common species, easily available for harvesting in the
northwest coast, is Saccorhiza polyschides grows in the lowest shore
and costal rocky reefs. It is almost exclusively used by local farmers
as natural fertilizer, but contains a substantial amount of valuable
compounds, particularly alginates, natural biopolymers of high
interest for many industrial applications.
Alginates are natural polysaccharides present in cell walls of
brown seaweed, highly biocompatible, with particular properties that
make them of high interest for the food, biotechnology, cosmetics
and pharmaceutical industries. Conventional extraction processes are
based on thermal treatment. They are lengthy and consume high
amounts of energy and solvents. In recent years, microwave-assisted
extraction (MAE) has shown enormous potential to overcome major
drawbacks that outcome from conventional plant material extraction
(thermal and/or solvent based) techniques, being also successfully
applied to the extraction of agar, fucoidans and alginates. In the
present study, acid pretreatment of brown seaweed Saccorhiza
polyschides for subsequent microwave-assisted extraction (MAE) of
alginate was optimized. Seaweeds were collected in Northwest
Portuguese coastal waters of the Atlantic Ocean between May and
August, 2014. Experimental design was used to assess the effect of
temperature and acid pretreatment time in alginate extraction.
Response surface methodology allowed the determination of the
optimum MAE conditions: 40 mL of HCl 0.1 M per g of dried
seaweed with constant stirring at 20ºC during 14h. Optimal acid
pretreatment conditions have enhanced significantly MAE of
alginates from Saccorhiza polyschides, thus contributing for the
development of a viable, more environmental friendly alternative to
conventional processes.