Abstract: Microstructural and hardening changes of
Fe-0.2wt.%V alloy and pure Fe irradiated with 100 keV hydrogen ions
at room temperature were investigated. It was found that dislocation
density varies dramatically after irradiation, ranging from dislocation
free to dense areas with tangled and complex dislocation
configuration. As the irradiated Fe-0.2wt.%V samples were annealed
at 773 K, the irradiation-induced dislocation loops disappear, while
many small precipitates with enriched C distribute in the matrix. Some
large precipitates with enriched V were also observed. The hardness of
Fe-0.2wt.%V alloy and pure Fe increases after irradiation, which
ascribes to the formation of dislocation loops in the irradiated
specimens. Compared with pure Fe, the size of the
irradiation-introduced dislocation loops in Fe-0.2wt.%V alloy
decreases and the density increases, the change of the hardness also
decreases.
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: In the present study, RBF neural networks were used
for predicting the performance and emission parameters of a
biodiesel engine. Engine experiments were carried out in a 4 stroke
diesel engine using blends of diesel and Honge methyl ester as the
fuel. Performance parameters like BTE, BSEC, Tex and emissions
from the engine were measured. These experimental results were
used for ANN modeling.
RBF center initialization was done by random selection and by
using Clustered techniques. Network was trained by using fixed and
varying widths for the RBF units. It was observed that RBF results
were having a good agreement with the experimental results.
Networks trained by using clustering technique gave better results
than using random selection of centers in terms of reduced MRE and
increased prediction accuracy. The average MRE for the performance
parameters was 3.25% with the prediction accuracy of 98% and for
emissions it was 10.4% with a prediction accuracy of 80%.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.
Abstract: In this contribution two approaches for calculating
optimal trajectories for highly automated vehicles are presented and
compared. The first one is based on a non-linear vehicle model, used
for evaluation. The second one is based on a simplified model and
can be implemented on a current ECU. In usual driving situations
both approaches show very similar results.
Abstract: This paper analyses the heat transfer performance and
fluid flow using different nanofluids in a square enclosure. The
energy equation and Navier-Stokes equation are solved numerically
using finite volume scheme. The effect of volume fraction
concentration on the enhancement of heat transfer has been studied
icorporating the Brownian motion; the influence of effective thermal
conductivity on the enhancement was also investigated for a range of
volume fraction concentration. The velocity profile for different
Rayleigh number. Water-Cu, water AL2O3 and water-TiO2 were
tested.
Abstract: This paper reports a novel actuating design that uses
the shear deformation of a piezoelectric actuator to deflect a
bulge-diaphragm for driving an array microdroplet ejector. In essence,
we employed a circular-shaped actuator poled radial direction with
remnant polarization normal to the actuating electric field for inducing
the piezoelectric shear effect. The array microdroplet ejector consists
of a shear type piezoelectric actuator, a vibration plate, two chamber
plates, two channel plates and a nozzle plate. The vibration, chamber
and nozzle plate components are fabricated using nickel
electroforming technology, whereas the channel plate is fabricated by
etching of stainless steel. The diaphragm displacement was measured
by the laser two-dimensional scanning vibrometer. The ejected
droplets of the microejector were also observed via an optic
visualization system.
Abstract: Diagram and drawing are important ways to
communicate and the reproduce of architectural design, Due to the
development of information and communication technology, the
professional thinking of architecture and interior design are also
change rapidly. In development process of design, diagram always
play very important role. This study is based on diagram theories,
observe and record interaction between man and objects, objects and
space, and space and time in a modern nuclear family. Construct a
method for diagram to systematically and visualized describe the
space plan of a modern nuclear family toward an intelligent design, to
assist designer to retrieve information and review event pattern of past
and present.
Abstract: As the trend in automotive technology is fast moving
towards hybridization and electrification to curb emissions as well as
to improve the fuel efficiency, air-conditioning systems in passenger
cars have not caught up with this trend and still remain as the major
energy consumers amongst others. Adsorption based air-conditioning
systems, e.g. with silica-gel water pair, which are already in use for
residential and commercial applications, are now being considered as
a technology leap once proven feasible for the passenger cars. In this
paper we discuss a methodology, challenges and feasibility of
implementing an adsorption based air-conditioning system in a
passenger car utilizing the exhaust waste heat. We also propose an
optimized control strategy with interfaces to the engine control unit
of the vehicle for operating this system with reasonable efficiency
supported by our simulation and validation results in a prototype
vehicle, additionally comparing to existing implementations,
simulation based as well as experimental. Finally we discuss the
influence of start-stop and hybrid systems on the operation strategy of
the adsorption air-conditioning system.
Abstract: We propose new multiple-channel piezoelectric (PZT)
actuated tunable optical filter based on racetrack multi-ring
resonators for wavelength de-multiplexing network applications. We
design tunable eight-channel wavelength de-multiplexer consisting of
eight cascaded PZT actuated tunable multi-ring resonator filter with a
channel spacing of 1.6nm. The filter for each channel is basically
structured on a suspended beam, sandwiched with piezoelectric
material and built in integrated ring resonators which are placed on
the middle of the beam to gain uniform stress and linearly varying
longitudinal strain. A reference single mode serially coupled multi
stage racetrack ring resonator with the same radii and coupling length
is designed with a line width of 0.8974nm with a flat top pass band at
1dB of 0.5205nm and free spectral range of about 14.9nm. In each
channel, a small change in the perimeter of the rings is introduced to
establish the shift in resonance wavelength as per the defined channel
spacing. As a result, when a DC voltage is applied, the beams will
elongate, which involves mechanical deformation of the ring
resonators that induces a stress and a strain, which brings a change in
refractive index and perimeter of the rings leading to change in the
output spectrum shift providing the tunability of central wavelength
in each channel. Simultaneous wave length shift as high as
45.54pm/
Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: A field study was conducted to evaluate the efficacy of
safflower plant for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. Field
experiments with randomized complete block design with five
treatments (control, compost amendments added at 20 and 40 t/daa,
and vermicompost amendments added at 20 and 40 t/daa) were
carried out. The quality of safflower seeds and oil (heavy metals and
fatty acid composition) were determined. Tested organic amendments
significantly influenced the chemical composition of safflower seeds
and oil. The compost and vermicompost treatments significantly
reduced heavy metals concentration in safflower seeds and oils, but
the effect differed among them. Addition of vermicompost and
compost leads to an increase in the content of palmitic acid and
linoleic acid, and a decrease in the stearic and oleic acids compared
with the control. A significant increase in the quantity of saturated
acids was observed in the variants with 20 t/daa of compost and 20
t/daa of vermicompost (9.1 and 8.9% relative to the control).
Safflower is a plant which is tolerant to heavy metals and can be
successfully used in the phytoremediation of heavy metal
contaminated soils. The processing of seeds to oil and using the
obtained oil for nutritional purposes will greatly reduce the cost of
phytoremediation.
Abstract: Due to the continuous increment of the load demand,
identification of weaker buses, improvement of voltage profile and
power losses in the context of the voltage stability problems has
become one of the major concerns for the larger, complex,
interconnected power systems. The objective of this paper is to
review the impact of Flexible AC Transmission System (FACTS)
controller in Wind generators connected electrical network for
maintaining voltage stability. Wind energy could be the growing
renewable energy due to several advantages. The influence of wind
generators on power quality is a significant issue; non uniform power
production causes variations in system voltage and frequency.
Therefore, wind farm requires high reactive power compensation; the
advances in high power semiconducting devices have led to the
development of FACTS. The FACTS devices such as for example
SVC inject reactive power into the system which helps in maintaining
a better voltage profile. The performance is evaluated on an IEEE 14
bus system, two wind generators are connected at low voltage buses
to meet the increased load demand and SVC devices are integrated at
the buses with wind generators to keep voltage stability. Power
flows, nodal voltage magnitudes and angles of the power network are
obtained by iterative solutions using MIPOWER.
Abstract: This paper contains the description of argumentation
approach for the problem of inductive concept formation. It is
proposed to use argumentation, based on defeasible reasoning with
justification degrees, to improve the quality of classification models,
obtained by generalization algorithms. The experiment’s results on
both clear and noisy data are also presented.
Abstract: Many factors influence the educational outcome of
students. Some of these have been studied by researchers with many
emphasizing the role of students, schools, governments, peer groups
and so on. More often than not, some of these factors influencing the
academic achievement of the students have been traced back to
parents and family; being the primary platform on which learning not
only begins but is nurtured, encouraged and developed which later
transforms to the performance of the students. This study not only
explores parental and related factors that predict academic
achievement through the review of relevant literatures but also,
investigates the influence of parental background on the academic
achievement of senior secondary school students in Ibadan North
Local Government Area of Oyo State, Nigeria. As one of the criteria
of the quality of education, students’ academic achievement was
investigated because it is most often cited as an indicator of school
effectiveness by school authorities and educationists. The data
collection was done through interviews and use of well-structured
questionnaires administered to one hundred students (100) within the
target local government. This was statistically analysed and the result
showed that parents’ attitudes towards their children’s education had
significant effect(s) on students’ self-reporting of academic
achievement. However, such factors as parental education and socioeconomic
background had no significant relationship with the
students’ self-reporting of academic achievement.
Abstract: The iron environment in Fe-doped Vycor Anode was
investigated with EXAFS using Brookhaven Synchrotron Light
Source. The iron-reducing Shewanella oneidensis culture was grown
in a microbial fuel cell under anaerobic respiration. The Fe bond
length was found to decrease and correlate with the amount of
biofilm growth on the Fe-doped Vycor Anode. The data suggests that
Fe-doped Vycor Anode would be a good substrate to study the
Shewanella oneidensis nanowire structure using EXAFS.
Abstract: The arsenic and iron environments in different growth
stages have been studied with EXAFS and XANES using
Brookhaven Synchrotron Light Source. Collard Greens plants were
grown and tissue samples were harvested. The project studied the
EXAFS and XANES of tissue samples using As and Fe K-edges. The
Fe absorption and the Fourier transform bond length information
were used as a control comparison. The Fourier transform of the
XAFS data revealed the coexistence of As (III) and As (V) in the As
bonding environment inside the studied plant tissue samples,
although the soil only had As (III). The data suggests that Collard
Greens has a novel pathway to handle arsenic absorption in soil.
Abstract: With the flourishing development of online shopping,
an increasing number of customers see online shopping as an
entertaining experience. Because the online consumer has a double
identity as a shopper and an Internet user, online shopping should offer
hedonic values of shopping and Internet usage. The purpose of this
study is to investigate hedonic online shopping motivations from the
perspectives of traditional hedonic value and flow theory.
The study adopted a focus group interview method, including two
online and two offline interviews. Four focus groups of shoppers
consisted of online professionals, online college students, offline
professionals and offline college students. The results of the study
indicate that traditional hedonic values and dimensions of flow theory
exist in the online shopping environment. The study indicated that
online shoppers seem to appreciate being able to learn things and grow
to become competitive achievers online. Comparisons of online
hedonic motivations between groups are conducted. This study serves
as a basis for the future growth of Internet marketing.
Abstract: Edge is variation of brightness in an image. Edge
detection is useful in many application areas such as finding forests,
rivers from a satellite image, detecting broken bone in a medical
image etc. The paper discusses about finding edge of multiple aerial
images in parallel. The proposed work tested on 38 images 37
colored and one monochrome image. The time taken to process N
images in parallel is equivalent to time taken to process 1 image in
sequential. Message Passing Interface (MPI) and Open Computing
Language (OpenCL) is used to achieve task and pixel level
parallelism respectively.
Abstract: This paper is aimed at proposing a rhombus shaped
wearable fractal antenna for wireless communication systems. The
geometrical descriptors of the antenna have been obtained using
bacterial foraging optimization (BFO) for wide band operation. The
method of moment based IE3D software has been used to simulate
the antenna and observed that miniaturization of 13.08% has been
achieved without degrading the resonating properties of the proposed
antenna. An analysis with different substrates has also been done in
order to evaluate the effectiveness of electrical permittivity on the
presented structure. The proposed antenna has low profile, light
weight and has successfully demonstrated wideband and multiband
characteristics for wearable electronic applications.