Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: This paper reports the viability of developing Zn-27Al
alloy matrix hybrid composites reinforced with alumina, graphite and
fly ash (solid waste bye product of coal in thermal power plants).
This research work was aimed at developing low cost-high
performance Zn-27Al matrix composite with low density. Alumina
particulates (Al2O3), graphite added with 0, 2, 3, 4 and 5 wt% fly ash
were utilized to prepare 10wt% reinforcing phase with Zn-27Al alloy
as matrix using two-step stir casting method. Density measurement,
estimated percentage porosity, tensile testing, micro hardness
measurement and optical microscopy were used to assess the
performance of the composites produced. The results show that the
hardness, ultimate tensile strength, and percent elongation of the
hybrid composites decrease with increase in fly ash content. The
maximum decrease in hardness and ultimate tensile strength of
13.72% and 15.25% respectively were observed for composite grade
containing 5wt% fly ash. The percentage elongation of composite
sample without fly ash is 8.9% which is comparable with that of the
sample containing 2wt% fly ash with percentage elongation of 8.8%.
The fracture toughness of the fly ash containing composites was
however superior to those of composites without fly ash with 5wt%
fly ash containing composite exhibiting the highest fracture
toughness. The results show that fly ash can be utilized as
complementary reinforcement in ZA-27 alloy matrix composite to
reduce cost.
Abstract: The present study analyzed the effect of discrimination
experience on the life satisfaction in women with severe disabilities
and the mediating effect of disability acceptance. In verifying this
mediating effect of disability acceptance between discrimination
experience and life satisfaction, both discrimination experience and
disability acceptance were found to be statistically significant in the
first and second phases. Disability acceptance was found to have a
mediating effect on the relationship between discrimination
experience and life satisfaction. Based on this finding, measures for
enhancing the quality of life in individuals with disabilities that
experience low levels of life satisfaction were proposed.
Abstract: Rapid population growth, urbanization and
industrialization are known as the most important factors of
environment problems. Elimination and management of solid wastes
are also within the most important environment problems. One of the
main problems in solid waste management is the selection of the best
site for elimination of solid wastes. Lately, Geographical Information
System (GIS) has been used for easing selection of landfill area. GIS
has the ability of imitating necessary economic, environmental and
political limitations. They play an important role for the site selection
of landfill area as a decision support tool. In this study; map layers will be studied for minimum effect of
environmental, social and cultural factors and maximum effect for
engineering/economic factors for site selection of landfill areas and
using GIS for a decision support mechanism in solid waste landfill
areas site selection will be presented in Aksaray/Turkey city,
Güzelyurt district practice.
Abstract: Structural failure is caused mainly by damage that
often occurs on structures. Many researchers focus on to obtain very
efficient tools to detect the damage in structures in the early state. In
the past decades, a subject that has received considerable attention in
literature is the damage detection as determined by variations in the
dynamic characteristics or response of structures. The study presents
a new damage identification technique. The technique detects the
damage location for the incomplete structure system using output
data only. The method indicates the damage based on the free
vibration test data by using ‘Two Points Condensation (TPC)
technique’. This method creates a set of matrices by reducing the
structural system to two degrees of freedom systems. The current
stiffness matrices obtain from optimization the equation of motion
using the measured test data. The current stiffness matrices compare
with original (undamaged) stiffness matrices. The large percentage
changes in matrices’ coefficients lead to the location of the damage. TPC technique is applied to the experimental data of a simply
supported steel beam model structure after inducing thickness change
in one element, where two cases consider. The method detects the
damage and determines its location accurately in both cases. In
addition, the results illustrate these changes in stiffness matrix can be
a useful tool for continuous monitoring of structural safety using
ambient vibration data. Furthermore, its efficiency proves that this
technique can be used also for big structures.
Abstract: Many existing amusement parks have been operated
with assistance of a variety of information and communications
technologies to design friendly and efficient service systems for
tourists. However, these systems leave various levels of decisions to
tourists to make by themselves. This incurs pressure on tourists and
thereby bringing negative experience in their tour. This paper
proposes a smart amusement park system to offer each tourist the
GPS-based customized plan without tourists making decisions by
themselves. The proposed system consists of the mobile app
subsystem, the central subsystem, and the detecting/counting
subsystem. The mobile app subsystem interacts with the central
subsystem. The central subsystem performs the necessary computing
and database management of the proposed system. The
detecting/counting subsystem aims to detect and compute the number
of visitors to an attraction. Experimental results show that the
proposed system can not only work well, but also provide an
innovative business operating model for owners of amusement parks.
Abstract: The purpose of the study is to find out relation of
moral massage between the authority and globalization in proverb.
Proverb is one of the many forms of cultural identity of the
Indonesian/Malay people filled with moral values. The values
contained within those proverbs are beneficial not only to the society,
but also to those who held power amidst on this era of globalization.
The method being used is qualitative research through content
analysis which is done by describing and uncovering the forms and
meanings of proverbs used within Indonesia Minangkabau society.
Sources for this study’s data were extracted from a Minangkabau
native speaker in the sub district of Tanah Abang, Jakarta. Said
sources were retrieved through a series of interviews with the
Minangkabau native speaker, whose speech is still adorned with
idiomatic expressions. The research findings show that there are 30
existed proverbs or idiomatic expressions in the Minangkabau
language often used by its indigenous people. The thirty data contain
moral values which are closely interwoven with the matter of power
and globalization. Analytical results show that the fourteen moral
values contained within proverbs reflect a firm connection between
rule and power in globalization; such as: responsible, brave,
togetherness and consensus, tolerance, politeness, thorough and
meticulous, honest and keeping promise, ingenious and learning,
care, self-correction, be fair, alert, arbitrary, self-awareness.
Structurally, proverbs possess an unchangeably formal construction;
symbolically, proverbs possess meanings that are clearly decided
through ethnographic communicative factors along with situational
and cultural contexts. Values contained within proverbs may be used
as a guide in social management, be it between fellow men, between
men and nature, or even between men and their Creator. Therefore,
the meanings and values contained within the morals of proverbs
could also be utilized as a counsel for those who rule and in charge of
power in order to stem the tides of globalization that had already
spread into sectoral, territorial and educational continuums.
Abstract: Comparative analysis of the properties of melon seed,
coconut fruit and their oil yield were evaluated in this work using
standard analytical technique AOAC. The results of the analysis
carried out revealed that the moisture contents of the samples studied
are 11.15% (melon) and 7.59% (coconut). The crude lipid content are
46.10% (melon) and 55.15% (coconut).The treatment combinations
used (leaching time, leaching temperature and solute: solvent ratio)
showed significant difference (p < 0.05) in yield between the
samples, with melon oil seed flour having a higher percentage range
of oil yield (41.30 – 52.90%) and coconut (36.25 – 49.83%). The
physical characterization of the extracted oil was also carried out.
The values gotten for refractive index are 1.487 (melon seed oil) and
1.361 (coconut oil) and viscosities are 0.008 (melon seed oil) and
0.002 (coconut oil). The chemical analysis of the extracted oils shows
acid value of 1.00mg NaOH/g oil (melon oil), 10.050mg NaOH/g oil
(coconut oil) and saponification value of 187.00mg/KOH (melon oil)
and 183.26mg/KOH (coconut oil). The iodine value of the melon oil
gave 75.00mg I2/g and 81.00mg I2/g for coconut oil. A standard
statistical package Minitab version 16.0 was used in the regression
analysis and analysis of variance (ANOVA). The statistical software
mentioned above was also used to optimize the leaching process.
Both samples gave high oil yield at the same optimal conditions. The
optimal conditions to obtain highest oil yield ≥ 52% (melon seed)
and ≥ 48% (coconut seed) are solute - solvent ratio of 40g/ml,
leaching time of 2hours and leaching temperature of 50oC. The two
samples studied have potential of yielding oil with melon seed giving
the higher yield.
Abstract: Inference plays an important role in the learning
process and it can lead to a rapid acquisition of a second language.
When learning a non-native language i.e., a critical language like
Arabic, the students depend on the teacher’s support most of the time
to learn new concepts. The students focus on memorizing the new
vocabulary and stress on learning all the grammatical rules. Hence,
the students became mechanical and cannot produce the language
easily. As a result, they are unable to predicate the meaning of words
in the context by relying heavily on the teacher, in that they cannot
link their prior knowledge or even identify the meaning of the words
without the support of the teacher. This study explores how the
teacher guides students learning during the inference process and
what are the processes of learning that can direct student’s inference.
Abstract: Massive rock avalanches formed some of the largest landslide deposits on Earth and they represent one of the major geohazards in high-relief mountains. This paper interprets a very large sedimentary fan (the Sernio fan, Valtellina, Northern Italy), located 20 Km SW from Val Pola Rock avalanche (1987), as the deposit of a partial collapse of a Deep Seated Gravitational Slope Deformation (DSGSD), afterwards eroded and buried by debris flows. The proposed emplacement sequence has been reconstructed based on geomorphological, structural and mechanical evidences. The Sernio fan is actually considered anomalous with reference to the very high ratio between the fan area (≈ 4.5km2) and the basin area (≈ 3km2). The morphology of the fan area is characterised by steep slopes (dip ≈ 20%) and the fan apex is extended for 1.8 km inside the small catchment basin. This sedimentary fan was originated by a landslide that interested a part of a large deep-seated gravitational slope deformation, involving a wide area of about 55 km². The main controlling factor is tectonic and it is related to the proximity to regional fault systems and the consequent occurrence of fault weak rocks (GSI locally lower than 10 with compressive stress lower than 20MPa). Moreover, the fan deposit shows sedimentary evidences of recent debris flow events. The best current explanation of the Sernio fan involves an initial failure of some hundreds of Mm3. The run-out was quite limited because of the morphology of Valtellina’s valley floor, and the deposit filled the main valley forming a landslide dam, as confirmed by the lacustrine deposits detected upstream the fan. Nowadays the debris flow events represent the main hazard in the study area.
Abstract: This paper introduces the concept and principle of data
cleaning, analyzes the types and causes of dirty data, and proposes
several key steps of typical cleaning process, puts forward a well
scalability and versatility data cleaning framework, in view of data
with attribute dependency relation, designs several of violation data
discovery algorithms by formal formula, which can obtain inconsistent
data to all target columns with condition attribute dependent no matter
data is structured (SQL) or unstructured (NoSql), and gives 6 data
cleaning methods based on these algorithms.
Abstract: Natural fibers are used in polymer composites to
improve mechanical properties to replace inorganic reinforcing
agents produced by non-renewable resources. The present study
investigates the tensile and flexural behaviors of palm fibers-high
density polyethylene (HDPE) composite as a function of volume
fraction. The surface of the fibers was treated by mercerization
treatments to improve the wetting behavior of the apolar HDPE. The
treatment characterization was obtained by scanning electron
microscopy, X-Ray diffraction and infrared spectroscopy. Results
evidences that a good adhesion interfacial between fibers-matrix
caused an increase strength and modulus flexural as well as tensile
strength in the modified fibers/HDPE composites when compared to
the pure HDPE and untreated fibers reinforced composites.
Abstract: Presented article outlines a rationale, why it is
necessary to develop competence about infrastructure risk in water
transport. Climate changes are evident and require special attention
and global monitoring. Current risk assessment methods for Inland
waterway transport just consider some dramatic events. We present a
new method for the assessment of risk and vulnerability of inland
waterway transport where river depth represents a crucial part. The
analysis of water level changes in the lower Danube was done for two
significant periods (1965-1979 and 1998-2012).
Abstract: Three purified diets were formulated using fish meal,
soya bean, wheat flour, palm oil, minerals and maltose. The
carbohydrate in the diets was increased from 5 to 15% by changing
the cellulose content to study the effect of dietary carbohydrate level
on the growth parameters of Nile tilapia Oreochromis niloticus. The
protein and the lipid contents were kept constant in all the diets. The
results showed that, weight gain, protein efficiency ratio, net protein
utilisation and hepatosomatic index of fish fed the diet containing
15% cellulose were the lowest among all groups. Addition, the fish
fed the diet containing 5% cellulose had the best specific growth rate,
and food conversion ratio. While, there was no effect of the dietary
cellulose levels on condition factor and survival rate. These results
indicate that Nile tilapia fingerlings are able to utilize dietary
cellulose does not exceed 10% in their feed for optimum growth.
Abstract: Analyzing the relation networks between the hospital
buildings which have complex structure and distinctive spatial
relationships is quite difficult. The hospital buildings which require
specialty in spatial relationship solutions during design and selfinnovation
through the developing technology should survive and
keep giving service even after the disasters such as earthquakes. In
this study, a hospital building where the load-bearing system was
strengthened because of the insufficient earthquake performance and
the construction of an additional building was required to meet the
increasing need for space was discussed and a comparative spatial
evaluation of the hospital building was made with regard to its status
before the change and after the change. For this reason, spatial
organizations of the building before change and after the change were
analyzed by means of Space Syntax method and the effects of the
change on space organization parameters were searched by applying
an analytical procedure. Using Depthmap UCL software,
Connectivity, Visual Mean Depth, Beta and Visual Integration
analyses were conducted. Based on the data obtained after the
analyses, it was seen that the relationships between spaces of the
building increased after the change and the building has become more
explicit and understandable for the occupants. Furthermore, it was
determined according to findings of the analysis that the increase in
depth causes difficulty in perceiving the spaces and the changes
considering this problem generally ease spatial use.
Abstract: Urban areas, as they have been developed and operate
today, are areas of accumulation of a significant amount of people
and a large number of activities that generate desires and reasons for
traveling. The territorial expansion of the cities as well as the need to
preserve the importance of the central city areas lead to the
continuous increase of transportation needs which in the limited
urban space results in creating serious traffic and operational
problems. The modern perception of urban planning is directed towards more
holistic approaches and integrated policies that make it economically
competitive, socially just and more environmentally friendly. Over
the last 25 years, the goal of sustainable transport development has
been central to the agenda of any plan or policy for the city. The
modern planning of urban space takes into account the economic and
social aspects of the city and the importance of the environment to
sustainable urban development. In this context, the European Union
promotes direct or indirect related interventions according to the
cohesion and environmental policies; many countries even had the
chance to actually test them. This paper explores the methods and processes that have been
developed towards this direction and presents a review and
systematic presentation of this work. The ultimate purpose of this
research is to effectively use this review to create a decision making
methodological framework which can be the basis of a useful
operational tool for sustainable urban planning.
Abstract: Istanbul-Karakoy Port, field of this study, has lost its
former significance in time due to the transformation of urban
functions. Today, activities for regeneration of this region continue in
two forms and scales. First of these activities is the "planned
transformation projects," which also includes “Galataport project”,
and the second one is "spontaneous transformation," which consists
of individual interventions. Galataport project that based on the idea
of arranging the area specifically for tourists was prepared in 2005
and became a topic of tremendous public debate. On the other hand,
the "spontaneous transformation" that is observed in Karakoy District
starts in 2004 with the foundation of “Istanbul Modern Museum”
which allowed the cultural integration of old naval warehouses of the
port to the daily life. Following this adaptive reuse intervention, the
district started to accommodate numerous art galleries, studios, caféworkshops
and design stores. In this context, this paper first examines
regeneration studies in obsolete port regions, analyzes the planned
and ongoing socio-spatial transformations in the specific case of
Karakoy and performs a critical review of the sustainability of the
proposals on how to reinstate the district in the active life of Istanbul.
Abstract: Chatter vibrations and process instabilities are the
most important factors limiting the productivity of the milling
process. Chatter can leads to damage of the tool, the part or the
machine tool. Therefore, the estimation and prediction of the process
stability is very important. The process stability depends on the
spindle speed, the depth of cut and the width of cut. In milling, the
process conditions are defined in the NC-program. While the spindle
speed is directly coded in the NC-program, the depth and width of cut
are unknown. This paper presents a new simulation based approach
for the prediction of the depth and width of cut of a milling process.
The prediction is based on a material removal simulation with an
analytically represented tool shape and a multi-dexel approach for the
workpiece. The new calculation method allows the direct estimation
of the depth and width of cut, which are the influencing parameters of
the process stability, instead of the removed volume as existing
approaches do. The knowledge can be used to predict the stability of
new, unknown parts. Moreover with an additional vibration sensor,
the stability lobe diagram of a milling process can be estimated and
improved based on the estimated depth and width of cut.
Abstract: This research studies the joint production,
maintenance and subcontracting control policy for an unreliable
deteriorating manufacturing system. Production activities are
controlled by a derivation of the Hedging Point Policy, and given that
the system is subject to deterioration, it reduces progressively its
capacity to satisfy product demand. Multiple deterioration effects are
considered, reflected mainly in the quality of the parts produced and
the reliability of the machine. Subcontracting is available as support
to satisfy product demand; also, overhaul maintenance can be
conducted to reduce the effects of deterioration. The main objective
of the research is to determine simultaneously the production,
maintenance and subcontracting rate, which minimize the total,
incurred cost. A stochastic dynamic programming model is
developed and solved through a simulation-based approach
composed of statistical analysis and optimization with the response
surface methodology. The obtained results highlight the strong
interactions between production, deterioration and quality, which
justify the development of an integrated model. A numerical example
and a sensitivity analysis are presented to validate our results.
Abstract: We investigated ecotoxicity and performed experiment
for removing ZnO nanoparticles in water. Short term exposure of
hatching test using fertilized eggs (O. latipes) showed deformity in
5ppm of ZnO nanoparticles solution. And in 10ppm ZnO nanoparticles
solution delayed hatching was observed. Hereine, chemical
precipitation method was suggested for removing ZnO nanoparticles
in water. The precipitated ZnO nanoparticles showed the form of ZnS
after addition of Na2S, and the form of Zn3(PO4)2 for Na2HPO4. The
removal efficiency of ZnO nanoparticles in water was closed to 100%
for two cases. In ecotoxicity evaluation of as-precipitated ZnS and
Zn3(PO4)2, they did not cause any acute toxicity for D. magna. It is
noted that this precipitation treatment of ZnO is effective to reduce the
potential cytotoxicity.