Abstract: In this paper, all variables are supposed to be integer
and positive. In this modern method, objective function is assumed to
be maximized or minimized but constraints are always explained like
less or equal to. In this method, choosing a dual combination of ideal
nonequivalent and omitting one of variables. With continuing this
act, finally, having one nonequivalent with (n-m+1) unknown
quantities in which final nonequivalent, m is counter for constraints,
n is counter for variables of decision.
Abstract: Enzymatic hydrolysis of starch from natural sources
finds potential application in commercial production of alcoholic
beverage and bioethanol. In this study the effect of starch
concentration, temperature, time and enzyme concentration were
studied and optimized for hydrolysis of cassava (Manihot esculenta)
starch powder (of mesh 80/120) into glucose syrup by immobilized
(using Polyacrylamide gel) a-amylase using central composite
design. The experimental result on enzymatic hydrolysis of cassava
starch was subjected to multiple linear regression analysis using
MINITAB 14 software. Positive linear effect of starch concentration,
enzyme concentration and time was observed on hydrolysis of
cassava starch by a-amylase. The statistical significance of the model
was validated by F-test for analysis of variance (p < 0.01). The
optimum value of starch concentration temperature, time and enzyme
concentration were found to be 4.5% (w/v), 45oC, 150 min, and 1%
(w/v) enzyme. The maximum glucose yield at optimum condition
was 5.17 mg/mL.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: A study was undertaken to investigate the effect of
liquid nitrogen aeration on mortalities of adult Cryptolestes
furrugineus, rusty grain beetles, in a prototype cardboard grain bin
equipped with an aeration system. The grain bin was filled with Hard
Red Spring wheat and liquid nitrogen was introduced from the bottom
of the bin. The survival of both cold acclimated and unacclimated C.
furrugineus was tested. The study reveals that cold acclimated insects
had higher survival than unacclimated insects under similar cooling
conditions. In most cases, mortalities of as high as 100% were
achieved at the bottom 100 cm of the grain bin for unacclimated
insects for most of the trials. Insect survival increased as the distance
from the bottom of the grain bin increased. There was no adverse
effect of liquid nitrogen aeration on wheat germination.
Abstract: Five lignin samples were fractionated with
Acetone/Water mixtures and the obtained fractions were subjected to
extensive structural characterization, including Fourier Transform
Infrared (FT-IR), Gel permeation Chromatography (GPC) and
Phosphorus-31 NMR spectroscopy (31P-NMR). The results showed
that for all studied lignins the solubility increases with the increment
of the acetone concentration. Wheat straw lignin has the highest
solubility in 90/10 (v/v) Acetone/Water mixture, 400 mg lignin being
dissolved in 1 mL mixture. The weight average molecular weight of
the obtained fractions increased with the increment of acetone
concentration and thus with solubility. 31P-NMR analysis based on
lignin modification by reactive phospholane into phosphitylated
compounds was used to differentiate and quantify the different types
of OH groups (aromatic, aliphatic, and carboxylic) found in the
fractions obtained with 70/30 (v/v) Acetone/Water mixture.
Abstract: This paper proposes transient angle stability
agents to enhance power system stability. The proposed transient
angle stability agents divided into two strategy agents. The
first strategy agent is a prediction agent that will predict power
system instability. According to the prediction agent-s output,
the second strategy agent, which is a control agent, is automatically
calculating the amount of active power reduction that can
stabilize the system and initiating a control action. The control
action considered is turbine fast valving. The proposed strategies
are applied to a realistic power system, the IEEE 50-
generator system. Results show that the proposed technique can
be used on-line for power system instability prediction and control.
Abstract: In the last decades, a number of robust fuzzy clustering algorithms have been proposed to partition data sets affected by noise and outliers. Robust fuzzy C-means (robust-FCM) is certainly one of the most known among these algorithms. In robust-FCM, noise is modeled as a separate cluster and is characterized by a prototype that has a constant distance δ from all data points. Distance δ determines the boundary of the noise cluster and therefore is a critical parameter of the algorithm. Though some approaches have been proposed to automatically determine the most suitable δ for the specific application, up to today an efficient and fully satisfactory solution does not exist. The aim of this paper is to propose a novel method to compute the optimal δ based on the analysis of the distribution of the percentage of objects assigned to the noise cluster in repeated executions of the robust-FCM with decreasing values of δ . The extremely encouraging results obtained on some data sets found in the literature are shown and discussed.
Abstract: Energy Efficiency Management is the heart of a
worldwide problem. The capability of a multi-agent system as a
technology to manage the micro-grid operation has already been
proved. This paper deals with the implementation of a decisional
pattern applied to a multi-agent system which provides intelligence to
a distributed local energy network considered at local consumer level.
Development of multi-agent application involves agent
specifications, analysis, design, and realization. Furthermore, it can
be implemented by following several decisional patterns. The
purpose of present article is to suggest a new approach for a
decisional pattern involving a multi-agent system to control a
distributed local energy network in a decentralized competitive
system. The proposed solution is the result of a dichotomous
approach based on environment observation. It uses an iterative
process to solve automatic learning problems and converges
monotonically very fast to system attracting operation point.
Abstract: Efficient handoff algorithms are a cost-effective way
of enhancing the capacity and QoS of cellular system. The higher
value of hysteresis effectively prevents unnecessary handoffs but
causes undesired cell dragging. This undesired cell dragging causes
interference or could lead to dropped calls in microcellular
environment. The problems are further exacerbated by the corner
effect phenomenon which causes the signal level to drop by 20-30 dB
in 10-20 meters. Thus, in order to maintain reliable communication
in a microcellular system new and better handoff algorithms must be
developed. A fuzzy based handoff algorithm is proposed in this paper
as a solution to this problem. Handoff on the basis of ratio of slopes
of normal signal loss to the actual signal loss is presented. The fuzzy
based solution is supported by comparing its results with the results
obtained in analytical solution.
Abstract: In the given article the creative arts is being
investigated in the modern era and from the aspect of the artistic
interrelationship, having created by the character of his personality
and as the viewer. A study in the identity formation terms, the
definition of its being unique, unity and similarity as a global issue of
the XXI century has been conducted by the analyzing the definitions
which characterize the human nature in the arts. Spiritual universality
and human existence have been considered in the art system as a
human who is a creator, as the man hero and as the character who is
the recipient as well as the analyses which have been conducted
along with the worldwide cultural and historical processes.
Abstract: In this paper, various algorithms for designing quadrature mirror filter are reviewed and a new algorithm is presented for the design of near perfect reconstruction quadrature mirror filter bank. In the proposed algorithm, objective function is formulated using the perfect reconstruction condition or magnitude response condition of prototype filter at frequency (ω = 0.5π) in ideal condition. The cutoff frequency is iteratively changed to adjust the filters coefficients using optimization algorithm. The performances of the proposed algorithm are evaluated in term of computation time, reconstruction error and number of iterations. The design examples illustrate that the proposed algorithm is superior in term of peak reconstruction error, computation time, and number of iterations. The proposed algorithm is simple, easy to implement, and linear in nature.
Abstract: The crystalline quality of the AlGaN/GaN high electron mobility transistor (HEMT) structure grown on a 200 mm silicon substrate has been investigated using UV-visible micro- Raman scattering and photoluminescence (PL). The visible Raman scattering probes the whole nitride stack with the Si substrate and shows the presence of a small component of residual in-plane stress in the thick GaN buffer resulting from a wafer bowing, while the UV micro-Raman indicates a tensile interfacial stress induced at the top GaN/AlGaN/AlN layers. PL shows a good crystal quality GaN channel where the yellow band intensity is very low compared to that of the near-band-edge transition. The uniformity of this sample is shown by measurements from several points across the epiwafer.
Abstract: In order to improve the effect of isolation structure, the
principles and behaviours of the base-isolation system are studied, and
the types and characteristics of the base-isolation are also discussed.
Compared to the traditional aseismatic structures, the base isolation
structures decrease the seismic response obviously: the total structural
aseismatic value decreases to 1/4-1/32 and the seismic shear stress in
the upper structure decreases to 1/14-1/23. In the huge seism, the
structure can have an obvious aseismatic effect.
Abstract: Burnishing is a method of finishing and hardening
machined parts by plastic deformation of the surface. Experimental
work based on central composite second order rotatable design has
been carried out on a lathe machine to establish the effects of ball
burnishing parameters on the surface roughness of brass material.
Analysis of the results by the analysis of variance technique and the
F-test show that the parameters considered, have significant effects
on the surface roughness.
Abstract: Activity-Based Costing (ABC) represents an
alternative paradigm to traditional cost accounting system and
it often provides more accurate cost information for decision
making such as product pricing, product mix, and make-orbuy
decisions. ABC models the causal relationships between
products and the resources used in their production and traces
the cost of products according to the activities through the use
of appropriate cost drivers. In this paper, the implementation
of the ABC in a manufacturing system is analyzed and a
comparison with the traditional cost based system in terms of
the effects on the product costs are carried out to highlight the
difference between two costing methodologies. By using this
methodology, a valuable insight into the factors that cause the
cost is provided, helping to better manage the activities of the
company.
Abstract: The crystallization kinetics and phase transformation
of SiO2.Al2O3.0,56P2O5.1,8CaO.0,56CaF2 glass have been
investigated using differential thermal analysis (DTA), x-ray
diffraction (XRD), and scanning electron microscopy (SEM). Glass
samples were obtained by melting the glass mixture at 14500С/120
min. in platinum crucibles. The mixture were prepared from
chemically pure reagents: SiO2, Al(OH)3, H3PO4, CaCO3 and CaF2.
The non-isothermal kinetics of crystallization was studied by
applying the DTA measurements carried out at various heating rates.
The activation energies of crystallization and viscous flow were
measured as 348,4 kJ.mol–1 and 479,7 kJ.mol–1 respectively. Value of
Avrami parameter n ≈ 3 correspond to a three dimensional of crystal
growth mechanism. The major crystalline phase determined by XRD
analysis was fluorapatite (Ca(PO4)3F) and as the minor phases –
fluormargarite (CaAl2(Al2SiO2)10F2) and vitlokite (Ca9P6O24). The
resulting glass-ceramic has a homogeneous microstructure, composed
of prismatic crystals, evenly distributed in glass phase.
Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: A genetic algorithm (GA) based feature subset
selection algorithm is proposed in which the correlation structure of
the features is exploited. The subset of features is validated according
to the classification performance. Features derived from the
continuous wavelet transform are potentially strongly correlated.
GA-s that do not take the correlation structure of features into
account are inefficient. The proposed algorithm forms clusters of
correlated features and searches for a good candidate set of clusters.
Secondly a search within the clusters is performed. Different
simulations of the algorithm on a real-case data set with strong
correlations between features show the increased classification
performance. Comparison is performed with a standard GA without
use of the correlation structure.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.