Abstract: The aim of this paper is to investigate accidents and
close call situations connected to the use of mobile phones in
working-age people ≥ 50 years old. The paper is part of a crosssectional
study that was carried out in 2002 in 15,000 working-age
Finns. The study showed that mobile-phone-related accidents and
close call situations, both at work and at leisure, are more common in
people under 50 years that in people ≥ 50 years old. However, people
under 50 use mobile phones more than those aged ≥ 50.
Abstract: Depositional environment and source potential of the
different organic-rich levels of Devonian age (up to 990m thick) from
the onshore EC-1 well (Southern Tunisia) were investigated based on
the analysis of more than 130 cutting samples by different
geochemical techniques (Rock-Eval pyrolysis, GC-MS). The
obtained results including Rock Eval Pyrolysis data and biomarker
distribution (terpanes, steranes and aromatics) have been used to
describe the depositional environment and to assess the thermal
maturity of the Devonian organic matter. These results show that the
Emsian deposits exhibit poor to fair TOC contents. The associated
organic matter is composed of mixed kerogen (type II/III), as
indicated by the predominance of C29 steranes over C27 and C28
homologous, that was deposited in a slightly reduced environment
favoring organic matter preservation. Thermal maturity assessed from
Tmax, TNR and MPI-1 values shows a mature stage of organic
matter. The Middle Devonian (Eifelian) shales are rich in type II
organic matter that was deposited in an open marine depositional
environment. The TOC values are high and vary between 2 and 7%
indicating good to excellent source rock. The relatively high HI
values (reaching 547 mg HC/g TOC) and the low values of t19/t23
tricyclic terpane ratio (< 0.2) confirm the marine origin of the organic
matter (type II). During the Upper Devonian, the organic matter was
deposited under variable redox conditions, oxic to suboxic which is
clearly indicated by the low C35/C34 hopanes ratio, immature to
marginally mature with the vitrinite reflectance ranging from 0.5 to
0.7 Ro and Tmax value of 426°C-436 °C and the TOC values range
between 0.8% to 4%.
Abstract: Experimental study of natural convection heat transfer
inside smooth and rough surfaces of vertical and inclined equilateral
triangular channels of different inclination angles with a uniformly
heated surface are performed. The inclination angle is changed from
15º to 90º. Smooth and rough surface of average roughness (0.02mm)
are used and their effect on the heat transfer characteristics are
studied. The local and average heat transfer coefficients and Nusselt
number are obtained for smooth and rough channels at different heat
flux values, different inclination angles and different Rayleigh
numbers (Ra) 6.48 × 105 ≤ Ra ≤ 4.78 × 106. The results show that
the local Nusselt number decreases with increase of axial distance
from the lower end of the triangular channel to a point near the upper
end of channel, and then, it slightly increases. Higher values of local
Nusselt number for rough channel along the axial distance compared
with the smooth channel. The average Nusselt number of rough
channel is higher than that of smooth channel by about 8.1% for
inclined case at θ = 45o and 10% for vertical case. The results
obtained are correlated using dimensionless groups for both rough
and smooth surfaces of the inclined and vertical triangular channels.
Abstract: In general, classical methods such as maximum
likelihood (ML) and least squares (LS) estimation methods are used
to estimate the shape parameters of the Burr XII distribution.
However, these estimators are very sensitive to the outliers. To
overcome this problem we propose alternative robust estimators
based on the M-estimation method for the shape parameters of the
Burr XII distribution. We provide a small simulation study and a real
data example to illustrate the performance of the proposed estimators
over the ML and the LS estimators. The simulation results show that
the proposed robust estimators generally outperform the classical
estimators in terms of bias and root mean square errors when there
are outliers in data.
Abstract: Specific leaf area (SLA; cm2leaf g-1leaf) the ratio of leaf
area to leaf dry mass is a key ecophysiological parameter influencing
leaf physiology, photosynthesis, and whole plant carbon gain and
also can be used as a rapid and diagnostic tool. In this study, two
species of soluble inorganic selenium forms, selenite (Se^IV) and
selenate (Se^VI) at different concentrations were investigated on maize
plants that were growing in nutrient solutions during 2 weeks and at
the end of the experiment, amounts of SLA for first and second
leaves of maize were measured. In accordance with the results we
observed that our regarded Se concentrations in both forms of Se^IV
and Se^VI were not effective on maize plants’ SLA significantly
although high level of 3 mg.kg-1 Se^IV had negative affect on growth
of the samples that had been treated by it but about Se^VI samples we
did not observe this state and our different considered Se^VI
concentrations were not toxic for maize plants.
Abstract: Phelipanche ramosa is the most damaging obligate
flowering parasitic weed on wide species of cultivated plants. The
semi-arid regions of the world are considered the main centers of this
parasitic plant that causes heavy infestation. This is due to its
production of high numbers of seeds (up to 200,000) that remain
viable for extended periods (up to 20 years). In this study, 13
treatments for the control of Phelipanche were carried out, which
included agronomic, chemical, and biological treatments and the use
of resistant plant methods. In 2014, a trial was performed at the
Department of Agriculture, Food and Environment, University of
Foggia (southern Italy), on processing tomato (cv ‘Docet’) grown in
pots filled with soil taken from a field that was heavily infested by P.
ramosa). The tomato seedlings were transplanted on May 8, 2014,
into a sandy-clay soil (USDA). A randomized block design with 3
replicates (pots) was adopted. During the growing cycle of the
tomato, at 70, 75, 81 and 88 days after transplantation, the number of
P. ramosa shoots emerged in each pot was determined. The tomato
fruit were harvested on August 8, 2014, and the quantitative and
qualitative parameters were determined. All of the data were
subjected to analysis of variance (ANOVA) using the JMP software
(SAS Institute Inc. Cary, NC, USA), and for comparisons of means
(Tukey's tests). The data show that each treatment studied did not
provide complete control against P. ramosa. However, the virulence
of the attacks was mitigated by some of the treatments tried: radicon
biostimulant, compost activated with Fusarium, mineral fertilizer
nitrogen, sulfur, enzone, and the resistant tomato genotype. It is
assumed that these effects can be improved by combining some of
these treatments with each other, especially for a gradual and
continuing reduction of the “seed bank” of the parasite in the soil.
Abstract: The aim of the present study was to examine whether
increasing molybdenum (Mo) concentration affects the growth and
Mo concentration of maize (Zea mays L. cv Norma SC) and
sunflower (Helianthus annuus L. cv Arena PR) seedlings within
laboratory conditions.
In this experiment, calcareous chernozem soil was used and Mo
was supplemented into the soil as ammonium molybdate
[(NH4)6Mo7O24.4H2O] in four different concentrations as follow: 0
(control), 30, 90 and 270 mg·kg-1.
In this study, we found that molybdenum in small amount (30
mg·kg-1) affects positively on growth of maize and sunflower
seedlings, however, higher concentration of Mo reduces the dry
weights of shoots and roots. In the case of maize the highest Mo
treatment (270 mg·kg-1) and in sunflower 90 mg·kg-1 treatment
caused significant reduction in plant growth.
In addition, we observed that molybdenum contents in the roots
and shoots were very low in case of control soil but were
significantly elevated with increasing concentration of Mo treatment.
Only in case of sunflower the highest 270 mg·kg-1 Mo treatment
caused decrease in Mo concentration.
Abstract: This exploratory study gives an overview of the
evolution of the main financial and performance indicators of the
Academic Spin-Off’s and High Growth Academic Spin-Off’s in year
3 and year 6 after its creation in the region of Catalonia in Spain. The
study compares and evaluates results of these different measures of
performance and the degree of success of these companies for each
University.
We found that the average Catalonian Academic Spin-Off is small
and have not achieved the sustainability stage at year 6. On the
contrary, a small group of High Growth Academic Spin-Off’s
exhibits robust performance with high profits in year 6. Our results
support the need to increase selectivity and support for these
companies especially near year 3, because are the ones that will bring
wealth and employment. University role as an investor has rigid
norms and habits that impede an efficient economic return from their
ASO investment.
Universities with high performance on sales and employment in
year 3 not always could sustain this growth in year 6 because their
ASO’s are not profitable. On the contrary, profitable ASO exhibit
superior performance in all measurement indicators in year 6. We
advocate the need of a balanced growth (with profits) as a way to
obtain subsequent continuous growth.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: The paper presents a thermodynamic cycle analysis
for three turboshaft engines. The first cycle is a Brayton cycle,
describing the evolution of a classical turboshaft, based on the
Klimov TV2 engine. The other four cycles aim at approaching an
Ericsson cycle, by replacing the Brayton cycle adiabatic expansion in
the turbine by quasi-isothermal expansion. The maximum quasi-
Ericsson cycles temperature is set to a lower value than the maximum
Brayton cycle temperature, equal to the Brayton cycle power turbine
inlet temperature, in order to decrease the engine NOx emissions.
Also, the power/expansion ratio distribution over the stages of the gas
generator turbine is maintained the same. In two of the considered
quasi-Ericsson cycles, the efficiencies of the gas generator turbine, as
well as the power/expansion ratio distribution over the stages of the
gas generator turbine are maintained the same as for the reference
case, while for the other two cases, the efficiencies are increased in
order to obtain the same shaft power as in the reference case. For the
two cases respecting the first condition, both the shaft power and the
thermodynamic efficiency of the engine decrease, while for the other
two, the power and efficiency are maintained, as a result of assuming
new, more efficient gas generator turbines.
Abstract: An experimental study was performed to investigate
the behavior and strength of proposed technique to connect
reinforced concrete (RC) beam to steel or composite columns. This
approach can practically be used in several types of building
construction. In this technique, the main beam of the frame consists
of a transfer part (part of beam; Tr.P) and a common reinforcement
concrete beam. The transfer part of the beam is connected to the
column, whereas the rest of the beam is connected to the transfer part
from each side. Four full-scale beam-column connections were tested
under static loading. The test parameters were the length of the
transfer part and the column properties. The test results show that
using of the transfer part technique leads to modify the deformation
capabilities for the RC beam and hence it increases its resistance
against failure. Increase in length of the transfer part did not
necessarily indicate an enhanced behavior. The test results contribute
to the characterization of the connection behavior between RC beam -
steel column and can be used to calibrate numerical models for the
simulation of this type of connection.
Abstract: The purpose of the present work was to develop an
innovative food product with nutritional properties as well as
appealing organoleptic qualities. The product, a jam, was prepared
with the beans’ cooking water combined with fresh apple or carrot,
without the addition of any conservatives. Three different jams were
produced: bean and carrot, bean and apple and bean, apple and
cinnamon. The developed products underwent a sensorial analysis
that revealed that the bean, apple and cinnamon jam was globally
better accepted. However, with this study, the consumers determined
that the bean and carrot jam had the most attractive color and the
bean and apple jam the better consistency. Additionally, it was
possible to analyze the jams for their chemical components, namely
fat, fiber, protein, sugars and antioxidant activity. The obtained
results showed that the bean and carrot jam had the highest lipid
content, while the bean, apple and cinnamon jam had the highest
fiber content, when compared to the other two jams. Regarding the
sugar content, both jams with apple revealed similar sugar values,
which were higher than the sugar content of the bean and carrot jam.
The antioxidant activity was on average 10 mg TE/g.
Abstract: The present work describes the implementation of the
Enhanced Collaborative Optimization (ECO) multilevel architecture
with a gradient-based optimization algorithm with the aim of
performing a multidisciplinary design optimization of a generic
unmanned aerial vehicle with morphing technologies. The concepts
of weighting coefficient and dynamic compatibility parameter are
presented for the ECO architecture. A routine that calculates the
aircraft performance for the user defined mission profile and vehicle’s
performance requirements has been implemented using low fidelity
models for the aerodynamics, stability, propulsion, weight, balance
and flight performance. A benchmarking case study for evaluating
the advantage of using a variable span wing within the optimization
methodology developed is presented.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: The objective of this study was to evaluate the
physical and chemical characteristics of Serra da Estrela cheese and
compare these results with those of the sensory analysis. For the
study were taken six samples of Serra da Estrela cheese produced
with 6 different ecotypes of thistle in a dairy situated in Penalva do
Castelo. The chemical properties evaluated were moisture content,
protein, fat, ash, chloride and pH; the physical properties studied
were color and texture; and finally a sensory evaluation was
undertaken. The results showed moisture varying in the range 40-
48%, protein in the range 15-20%, fat between 41-45%, ash between
3.9-5.0% and chlorides varying from 1.2 to 3.0%. The pH varied
from 4.8 to 5.4. The textural properties revealed that the crust
hardness is relatively low (maximum 7.3 N), although greater than
flesh firmness (maximum 1.7 N), and also that these cheeses are in
fact soft paste type, with measurable stickiness and intense
adhesiveness. The color analysis showed that the crust is relatively
light (L* over 50), and with a predominant yellow coloration (b*
around 20 or over) although with a slight greenish tone (a* negative).
The results of the sensory analysis did not show great variability for
most of the attributes measured, although some differences were
found in attributes such as crust thickness, crust uniformity, and
creamy flesh.
Abstract: Flours of wheat, chestnut, acorn and lupin were
evaluated in relation to phenolic compounds, antioxidant activity, and
oxalate content. At the chemical level the results show some
variability between samples by type of flour, and the sample of
chestnut flour presented the higher value of oxalate (0.00348
mg/100g) when compared to the other samples in the study.
Considering the content of phenolic compounds, the sample that
stood out was the acorn flour, having a high value of 0.812 g
AGE/100 g. All the samples presented intermediate content of
antioxidant activity and the sample that showed a slightly higher
value was the wheat flour with a value of 0.746 mM TRE/g sample.
Abstract: There has been a significant decline in active travel
and a massive increase in the use of car dependent travel in many
countries during the past two decades. Evidential risks for people’s
physical and mental health problems are correlated with this
increased use of motorized travel. These health related problems
range from overweight and obesity to increased air pollution. In
response to these rising concerns health professionals, traffic planers,
local authorities and others have introduced a variety of initiatives to
counterbalance the dominance of cars for daily journeys.
However, the nature of travel behavior change interventions,
which aim to reduce car use, are very complex and challenging
regarding their interactions with human behavior. To change travel
behavior at least two aspects have to be taken into consideration.
First, how to alter attitudes and perceptions toward the sustainable
and healthy modes of travel, in competition with experiences of
private car use. And second, how to make these behavior change
processes irreversible and sustainable. There are no comprehensive
models available to guide policy interventions to increase the level of
success of travel behavior change interventions across both these
dimensions.
A comprehensive theoretical framework is required in the effort to
optimize how to facilitate and guide the processes of data collection
and analysis to achieve the best possible guidelines for policy
makers. Regarding the gaps in the travel behavior change research
literature, this paper attempted to identify and suggest a
multidimensional framework in order to facilitate planning the
implemented travel behavior change interventions. A structured
mixed-method model is suggested to improve the analytic power of
the results according to the complexity of human behavior.
In order to recognize people’s attitudes towards a specific travel
mode, the Theory of Planned Behavior (TPB) was operationalized.
But in order to capture decision making processes the Transtheoretical
model of Behavior Change (TTM) was also used.
Consequently, the combination of these two theories (TTM and TPB)
has resulted in a synthesis with appropriate concepts to identify and
design an implemented travel behavior change interventions.
Abstract: Blueberries are widely valued for their high content in
phenolic compounds with antioxidant activity, and hence beneficial
for the human health. In this way, a study was done to determine the
phenolic composition (total phenols, anthocyanins and tannins) and
antioxidant activity of blueberries from three cultivars (Duke,
Bluecrop, and Ozarkblue) grown in two different Portuguese farms.
Initially two successive extractions were done with methanol
followed by two extractions with aqueous acetone solutions. These
extracts obtained were then used to evaluate the amount of phenolic
compounds and the antioxidant activity. The total phenols were
observed to vary from 4.9 to 8.2 mg GAE/g fresh weight, with
anthocyanin’s contents in the range 1.5-2.8 mg EMv3G/g and tannins
contents in the range 1.5- 3.8 mg/g. The results for antioxidant
activity ranged from 9.3 to 23.2 molTE/g and from 24.7 to 53.4molTE/g, when measured, respectively, by DPPH and ABTS
methods. In conclusion it was observed that, in general, the cultivar
had a visible effect on the phenols present, and furthermore, the
geographical origin showed relevance either in the phenols contents
or the antioxidant activity.
Abstract: Analysis of the properties of coconut (Cocos nucifera)
and its oil was evaluated in this work using standard analytical
techniques. The analyses carried out include proximate composition
of the fruit, extraction of oil from the fruit using different process
parameters and physicochemical analysis of the extracted oil. The
results showed the percentage (%) moisture, crude lipid, crude
protein, ash and carbohydrate content of the coconut as 7.59, 55.15,
5.65, 7.35 and 19.51 respectively. The oil from the coconut fruit was
odourless and yellowish liquid at room temperature (30oC). The
treatment combinations used (leaching time, leaching temperature
and solute: solvent ratio) showed significant differences (P
Abstract: The concept of technology as well as itself has
evolved continuously over time, such that, nowadays, this concept is
still marked by myths and realities. Even the concept of science is
frequently misunderstood as technology. In this way, this paper
presents different forms of interpretation of the concept of technology
in the course of history, as well as the social and cultural aspects
associated with it, through an analysis made by means of insights
from sociological studies of science and technology and its multiple
relations with society. Through the analysis of contents, the paper
presents a classification of how technology is interpreted in the social
sphere and search channel efforts to show how a broader
understanding can contribute to better interpretations of how
scientific and technological development influences the environment
in which we operate. The text also presents a particular point of view
for the interpretation of the concept from the analysis throughout the
whole work.