Abstract: This paper presents the simulation results of the
effects of sampling frequency on the total harmonic distortion (THD)
of three-phase inverters using the space vector pulse width
modulation (SVPWM) and space vector control (SVC) algorithms.
The relationship between the variables was studied using curve fitting
techniques, and it has been shown that, for 50 Hz inverters, there is
an exponential relation between the sampling frequency and THD up
to around 8500 Hz, beyond which the performance of the model
becomes irregular, and there is an negative exponential relation
between the sampling frequency and the marginal improvement to
the THD. It has also been found that the performance of SVPWM is
better than that of SVC with the same sampling frequency in most
frequency range, including the range where the performance of the
former is irregular.
Abstract: Load modeling is one of the central functions in
power systems operations. Electricity cannot be stored, which means
that for electric utility, the estimate of the future demand is necessary
in managing the production and purchasing in an economically
reasonable way. A majority of the recently reported approaches are
based on neural network. The attraction of the methods lies in the
assumption that neural networks are able to learn properties of the
load. However, the development of the methods is not finished, and
the lack of comparative results on different model variations is a
problem. This paper presents a new approach in order to predict the
Tunisia daily peak load. The proposed method employs a
computational intelligence scheme based on the Fuzzy neural
network (FNN) and support vector regression (SVR). Experimental
results obtained indicate that our proposed FNN-SVR technique gives
significantly good prediction accuracy compared to some classical
techniques.
Abstract: For the treatment of acute and chronic lung diseases it is preferred to deliver medicaments by inhalation. The drug is delivered directly to tracheobronchial tree. This way allows the given medicament to get directly into the place of action and it makes rapid onset of action and maximum efficiency. The transport of aerosol particles in the particular part of the lung is influenced by their size, anatomy of the lungs, breathing pattern and airway resistance. This article deals with calculation of airway resistance in the lung model of Horsfield. It solves the problem of determination of the pressure losses in bifurcation and thus defines the pressure drop at a given location in the bronchial tree. The obtained data will be used as boundary conditions for transport of aerosol particles in a central part of bronchial tree realized by Computational Fluid Dynamics (CFD) approach. The results obtained from CFD simulation will allow us to provide information on the required particle size and optimal inhalation technique for particle transport into particular part of the lung.
Abstract: The aim of this study is to develop an anterior lumbar
interbody fusion (ALIF) PEEK cage suitable for Korean people. In this
study, CT images were obtained from Korean male (173cm, 71kg) and
3D Korean lumbar models were reconstructed based on the CT images
to investigate anatomical characteristics. Major design parameters of
anterior lumbar interbody fusion (ALIF) PEEK Cage were selected
using the morphological measurement information of the Korean
Lumbar models. Through finite element analysis and mechanical tests,
the developed ALIFPEEK Cage prototype was compared with the
Fidji Cage (Zimmer. Inc, USA) and it was found that the ALIF
prototype showed similar and/or superior mechanical performance
compared to the FidJi Cage. Also, clinical validation for the ALIF
PEEK Cage prototype was carried out to check predictable troubles in
surgical operations. Finally, it is considered that the convenience and
stability of the prototype was clinically verified.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: Reverse Logistics (RL) Network is considered as
complex and dynamic network that involves many stakeholders such
as: suppliers, manufactures, warehouse, retails and costumers, this
complexity is inherent in such process due to lack of perfect
knowledge or conflicting information. Ontologies on the other hand
can be considered as an approach to overcome the problem of sharing
knowledge and communication among the various reverse logistics
partners. In this paper we propose a semantic representation based on
hybrid architecture for building the Ontologies in ascendant way, this
method facilitates the semantic reconciliation between the
heterogeneous information systems that support reverse logistics
processes and product data.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: Although it is not intended to identify distance
education students as a homogeneous group, recent research has
demonstrated that there are some demographic and personality
common traits among most of them that provide the basis for the
description of a typical distance learning student. The purpose of this
paper is to describe these common traits and to facilitate their
learning journey within a distance education program. The described
research is an initiative of the Distance Education Unit at the
European University Cyprus (Laureate International Universities) in
the context of its action for the improvement of the students’
performance.
Abstract: In the scope of application of technical textiles, Non-
Crimp Fabrics are increasingly used. In general, NCF exhibit
excellent load bearing properties, but caused by the manufacturing
process, there are some remaining disadvantages which have to be
reduced. Regarding to this, a novel technique of processing NCF was
developed substituting the binding-thread by an adhesive. This stitchfree
method requires new manufacturing concept as well as new basic
methods to prove adhesion of glue at fibres and textiles. To improve
adhesion properties and the wettability of carbon-fibres by the
adhesive, oxy-fluorination was used. The modification of carbonfibres
by oxy-fluorination was investigated via scanning electron
microscope, X-ray photoelectron spectroscopy and single fibre
tensiometry. Special tensile tests were developed to determine the
maximum force required for detachment.
Abstract: In this study, we propose a novel technique for acoustic
echo suppression (AES) during speech recognition under barge-in
conditions. Conventional AES methods based on spectral subtraction
apply fixed weights to the estimated echo path transfer function
(EPTF) at the current signal segment and to the EPTF estimated until
the previous time interval. However, the effects of echo path changes
should be considered for eliminating the undesired echoes. We
describe a new approach that adaptively updates weight parameters in
response to abrupt changes in the acoustic environment due to
background noises or double-talk. Furthermore, we devised a voice
activity detector and an initial time-delay estimator for barge-in speech
recognition in communication networks. The initial time delay is
estimated using log-spectral distance measure, as well as
cross-correlation coefficients. The experimental results show that the
developed techniques can be successfully applied in barge-in speech
recognition systems.
Abstract: It is difficult to study the effect of various variables on
cycle fitting through actual experiment. To overcome such difficulty,
the forward dynamics of a musculoskeletal model was applied to cycle
fitting in this study. The measured EMG data weres compared with the
muscle activities of the musculoskeletal model through forward
dynamics. EMG data were measured from five cyclists who do not
have musculoskeletal diseases during three minutes pedaling with a
constant load (150 W) and cadence (90 RPM). The muscles used for
the analysis were the Vastus Lateralis (VL), Tibialis Anterior (TA),
Bicep Femoris (BF), and Gastrocnemius Medial (GM). Person’s
correlation coefficients of the muscle activity patterns, the peak timing
of the maximum muscle activities, and the total muscle activities were
calculated and compared. BIKE3D model of AnyBody (Anybodytech,
Denmark) was used for the musculoskeletal model simulation. The
comparisons of the actual experiments with the simulation results
showed significant correlations in the muscle activity patterns (VL:
0.789, TA: 0.503, BF: 0.468, GM: 0.670). The peak timings of the
maximum muscle activities were distributed at particular phases. The
total muscle activities were compared with the normalized muscle
activities, and the comparison showed about 10% difference in the VL
(+10%), TA (+9.7%), and BF (+10%), excluding the GM (+29.4%).
Thus, it can be concluded that muscle activities of model &
experiment showed similar results. The results of this study indicated
that it was possible to apply the simulation of further improved
musculoskeletal model to cycle fitting.
Abstract: Modular structural systems are constructed using a
method that they are assembled with prefabricated unit modular
frames on-site. This provides a benefit that can significantly reduce
building construction time. The structural design is usually carried out
under the assumption that their load-carrying mechanism is similar to
that of traditional steel moment-resisting systems. However, both
systems are different in terms of beam-column connection details
which may strongly influence the lateral structural behavior. Specially,
the presence of access holes in a beam-column joint of a unit modular
frame could cause undesirable failure during strong earthquakes.
Therefore, this study carried out finite element analyses (FEMs) of
unit modular frames to investigate the cyclic behavior of beam-column
joints with the access holes. Analysis results show that the unit
modular frames present stable cyclic response with large deformation
capacities and their joints are classified into semi-rigid connections
even if there are access holes.
Abstract: A feeding experiment was conducted to determine the
optimum dietary protein and lipid levels for juvenile fancy carp. Eight
experimental diets were formulated to contain four protein levels (200,
300, 400 and 500 g kg-1) with two lipid levels (70 and 140 g kg-1).
Triplicate groups of fish (initial weight, 12.1±0.2 g fish-1) were
hand-fed the diets to apparent satiation for 8 weeks. Fish growth
performance, feed utilization and feed intake were significantly
(P0.05). Weight gain and feed efficiency ratio tended to
increase as dietary protein level increased up to 400 and 500 g kg-1,
respectively. Daily feed intake of fish decreased with increasing
dietary protein level and that of fish fed diet contained 500 g kg-1
protein was significantly lower than other fish groups. The protein
efficiency ratio of fish fed 400 and 500 g kg-1 protein was lower than
that of fish fed 200 and 300 g kg-1 protein. Moisture, crude protein and
crude lipid contents of muscle and liver were significantly affected by
dietary protein, but not by dietary lipid level (P>0.05). The increase in
dietary lipid level resulted in an increase in linoleic acid in liver and
muscle paralleled with a decrease in n-3 highly unsaturated fatty acids
content in muscle of fish. In considering these results, it was concluded
that the diet containing 400 g kg-1 protein with 70 g kg-1 lipid level is
optimal for growth and efficient feed utilization of juvenile fancy carp.
Abstract: The ad hoc networks are the future of wireless
technology as everyone wants fast and accurate error free information
so keeping this in mind Bit Error Rate (BER) and power is optimized
in this research paper by using the Genetic Algorithm (GA). The
digital modulation techniques used for this paper are Binary Phase
Shift Keying (BPSK), M-ary Phase Shift Keying (M-ary PSK), and
Quadrature Amplitude Modulation (QAM). This work is
implemented on Wireless Ad Hoc Networks (WLAN). Then it is
analyze which modulation technique is performing well to optimize
the BER and power of WLAN.
Abstract: Nanocrystalline powders of the lead-free piezoelectric
material, tantalum-substituted potassium sodium niobate
(K0.5Na0.5)(Nb0.9Ta0.1)O3 (KNNT), were produced using a Retsch
PM100 planetary ball mill by setting the milling time to 15h, 20h,
25h, 30h, 35h and 40h, at a fixed speed of 250rpm. The average
particle size of the milled powders was found to decrease from 12nm
to 3nm as the milling time increases from 15h to 25h, which is in
agreement with the existing theoretical model. An anomalous
increase to 98nm and then a drop to 3nm in the particle size were
observed as the milling time further increases to 30h and 40h
respectively. Various sizes of these starting KNNT powders were
used to investigate the effect of milling time on the microstructure,
dielectric properties, phase transitions and piezoelectric properties of
the resulting KNNT ceramics. The particle size of starting KNNT
was somewhat proportional to the grain size. As the milling time
increases from 15h to 25h, the resulting ceramics exhibit
enhancement in the values of relative density from 94.8% to 95.8%,
room temperature dielectric constant (εRT) from 878 to 1213, and
piezoelectric charge coefficient (d33) from 108pC/N to 128pC/N. For
this range of ceramic samples, grain size refinement suppresses the
maximum dielectric constant (εmax), shifts the Curie temperature (Tc)
to a lower temperature and the orthorhombic-tetragonal phase
transition (Tot) to a higher temperature. Further increase of milling
time from 25h to 40h produces a gradual degradation in the values of
relative density, εRT, and d33 of the resulting ceramics.
Abstract: Vacuum insulation panel (VIP) is a promising thermal
insulator for buildings, refrigerator, LNG carrier and so on. In general,
it has the thermal conductivity of 2~4 mW/m·K. However, this thermal
conductivity is that measured at the center of VIP. The total effective
thermal conductivity of VIP is larger than this value due to the edge
conduction through the envelope. In this paper, the edge conduction of
VIP is examined theoretically, numerically and experimentally. To
confirm the existence of the edge conduction, numerical analysis is
performed for simple two-dimensional VIP model and a theoretical
model is proposed to calculate the edge conductivity. Also, the edge
conductivity is measured using the vacuum guarded hot plate and the
experiment is validated against numerical analysis. The results show
that the edge conductivity is dependent on the width of panel and
thickness of Al-foil. To reduce the edge conduction, it is recommended
that the VIP should be made as big as possible or made of thin Al film
envelope.
Abstract: This study is purposed to develop an efficient fault
detection method for Global Navigation Satellite Systems (GNSS)
applications based on adaptive noise covariance estimation. Due to the
dependence on radio frequency signals, GNSS measurements are
dominated by systematic errors in receiver’s operating environment.
In the proposed method, the pseudorange and carrier-phase
measurement noise covariances are obtained at time propagations and
measurement updates in process of Carrier-Smoothed Code (CSC)
filtering, respectively. The test statistics for fault detection are
generated by the estimated measurement noise covariances. To
evaluate the fault detection capability, intentional faults were added to
the filed-collected measurements. The experiment result shows that
the proposed method is efficient in detecting unhealthy measurements
and improves GNSS positioning accuracy against fault occurrences.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: The paper deals with communication standards for
control and production system. The authors formulate the
requirements for communication security protection. The paper is
focused on application protocols of the industrial networks and their
basic classification. The typical attacks are analysed and the safety
protection, based on requirements for specific industrial network is
suggested and defined in this paper.
Abstract: Identification and selection of appropriate product and
manufacturing technologies are key factors for competitiveness and
market success of technology-based companies. Therefore, many
companies perform technology intelligence (TI) activities to ensure
the identification of evolving technologies at the right time.
Technology monitoring is one of the three base activities of TI,
besides scanning and scouting.
As the technological progress is accelerating, more and more
technologies are being developed. Against the background of limited
resources it is therefore necessary to focus TI activities. In this paper
we propose a concept for defining appropriate search fields for
technology monitoring. This limitation of search space leads to more
concentrated monitoring activities. The concept will be introduced
and demonstrated through an anonymized case study conducted
within an industry project at the Fraunhofer Institute for Production
Technology IPT.
The described concept provides a customized monitoring
approach, which is suitable for use in technology-oriented companies.
It is shown in this paper that the definition of search fields and search
tasks are suitable methods to define topics of interest and thus to
align monitoring activities. Current as well as planned product,
production and material technologies and existing skills, capabilities
and resources form the basis for derivation of relevant search areas.
To further improve the concept of technology monitoring the
proposed concept should be extended during future research e.g. by
the definition of relevant monitoring parameters.