Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: Use of the Internet and the World-Wide-Web
(WWW) has become widespread in recent years and mobile agent
technology has proliferated at an equally rapid rate. In this scenario
load balancing becomes important for P2P systems. Beside P2P
systems can be highly heterogeneous, i.e., they may consists of peers
that range from old desktops to powerful servers connected to
internet through high-bandwidth lines. There are various loads
balancing policies came into picture. Primitive one is Message
Passing Interface (MPI). Its wide availability and portability make it
an attractive choice; however the communication requirements are
sometimes inefficient when implementing the primitives provided by
MPI. In this scenario we use the concept of mobile agent because
Mobile agent (MA) based approach have the merits of high
flexibility, efficiency, low network traffic, less communication
latency as well as highly asynchronous. In this study we present
decentralized load balancing scheme using mobile agent technology
in which when a node is overloaded, task migrates to less utilized
nodes so as to share the workload. However, the decision of which
nodes receive migrating task is made in real-time by defining certain
load balancing policies. These policies are executed on PMADE (A
Platform for Mobile Agent Distribution and Execution) in
decentralized manner using JuxtaNet and various load balancing
metrics are discussed.
Abstract: This paper describes Clinical Document Architecture Release Two (CDA R2) standard and a client application for messaging with SAĞLIK-NET project developed by The Ministry of Health of Turkey. CDA R2 , developed by Health Level 7 (HL7) organization and approved by American National Standards Institute (ANSI) in 2004, to standardize medical information to be able to share semantically and syntactically. In this study, a client application compatible with HL7 V3 for a project named SAĞLIKNET, aimed to build a National Health Information System by Turkey. Moreover, CDA conformance of this application will also be evaluated.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: Microwave energy can be used for drying purpose. It is unique process. It is distinctly different from conventional drying process. It is advantageous over conventional drying / heating processes. When microwave energy is used for drying purpose, the process can be accelerated with a better control to achieve uniform heating, more conversion efficiency, selective drying and ultimately improved product quality of the output. Also, less floor space and compact system are the added advantages. Existing low power microwave drying system is to be modified with suitable applicator. Appropriate sensors are to be used to measure parameters like moisture, temperature, weight of sample. Suitable high tech controller is to be used to control microwave power continuously from minimum to maximum. Phase - controller, cycle - controller and PWM - controller are some of the advanced power control techniques. It has been proposed to work on turmeric using high-tech phase controller to control the microwave power conveniently. The drying of turmeric with microwave energy employing phase controller gives better results as formulated in this paper and hence new approach of processing turmeric will open future doors of profit making to allied industries and the farmers.
Abstract: Steganography, derived from Greek, literally means
“covered writing". It includes a vast array of secret communications
methods that conceal the message-s very existence. These methods
include invisible inks, microdots, character arrangement, digital
signatures, covert channels, and spread spectrum communications.
This paper proposes a new improved version of Least Significant Bit
(LSB) method. The approach proposed is simple for implementation
when compared to Pixel value Differencing (PVD) method and yet
achieves a High embedding capacity and imperceptibility. The
proposed method can also be applied to 24 bit color images and
achieve embedding capacity much higher than PVD.
Abstract: This paper deals with the experimental investigations
of the in-cylinder tumble flows in an unfired internal combustion
engine with a flat piston at the engine speeds ranging from 400 to
1000 rev/min., and also with the dome and dome-cavity pistons at an
engine speed of 1000 rev/min., using particle image velocimetry.
From the two-dimensional in-cylinder flow measurements, tumble
flow analysis is carried out in the combustion space on a vertical
plane passing through cylinder axis. To analyze the tumble flows,
ensemble average velocity vectors are used and to characterize it,
tumble ratio is estimated. From the results, generally, we have found
that tumble ratio varies mainly with crank angle position. Also, at the
end of compression stroke, average turbulent kinetic energy is more
at higher engine speeds. We have also found that, at 330 crank angle
position, flat piston shows an improvement of about 85 and 23% in
tumble ratio, and about 24 and 2.5% in average turbulent kinetic
energy compared to dome and dome-cavity pistons respectively
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: Rice husk is a lignocellulosic source that can be
converted to ethanol. Three hundreds grams of rice husk was mixed
with 1 L of 0.18 N sulfuric acid solutions then was heated in an
autoclave. The reaction was expected to be at constant temperature
(isothermal), but before that temperature was achieved, reaction has
occurred. The first liquid sample was taken at temperature of 140 0C
and repeated every 5 minute interval. So the data obtained are in the
regions of non-isothermal and isothermal. It was observed that the
degradation has significant effects on the ethanol production. The
kinetic constants can be expressed by Arrhenius equation with the
frequency factors for hydrolysis and sugar degradation of 1.58 x 105
min-1 and 2.29 x 108 L/mole-min, respectively, while the activation
energies are 64,350 J/mole and 76,571 J/mole. The highest ethanol
concentration from fermentation is 1.13% v/v, attained at 220 0C.
Abstract: Research papers are usually evaluated via peer
review. However, peer review has limitations in evaluating research
papers. In this paper, Scienstein and the new idea of 'collaborative
document evaluation' are presented. Scienstein is a project to
evaluate scientific papers collaboratively based on ratings, links,
annotations and classifications by the scientific community using the
internet. In this paper, critical success factors of collaborative
document evaluation are analyzed. That is the scientists- motivation
to participate as reviewers, the reviewers- competence and the
reviewers- trustworthiness. It is shown that if these factors are
ensured, collaborative document evaluation may prove to be a more
objective, faster and less resource intensive approach to scientific
document evaluation in comparison to the classical peer review
process. It is shown that additional advantages exist as collaborative
document evaluation supports interdisciplinary work, allows
continuous post-publishing quality assessments and enables the
implementation of academic recommendation engines. In the long
term, it seems possible that collaborative document evaluation will
successively substitute peer review and decrease the need for
journals.
Abstract: In this paper, a new secure watermarking scheme for
color image is proposed. It splits the watermark into two shares using
(2, 2)- threshold Visual Cryptography Scheme (V CS) with Adaptive
Order Dithering technique and embeds one share into high textured
subband of Luminance channel of the color image. The other share
is used as the key and is available only with the super-user or the
author of the image. In this scheme only the super-user can reveal
the original watermark. The proposed scheme is dynamic in the sense
that to maintain the perceptual similarity between the original and the
watermarked image the selected subband coefficients are modified
by varying the watermark scaling factor. The experimental results
demonstrate the effectiveness of the proposed scheme. Further, the
proposed scheme is able to resist all common attacks even with strong
amplitude.
Abstract: The possibility of producing drinking water from
brackish ground water using Vacuum membrane distillation (VMD)
process was studied. It is a rising technology for seawater or brine
desalination process. The process simply consists of a flat sheet
hydrophobic micro porous PTFE membrane and diaphragm vacuum
pump without a condenser for the water recovery or trap. In this
work, VMD performance was investigated for aqueous NaCl solution
and natural ground water. The influence of operational parameters
such as feed flow rate (30 to 55 l/h), feed temperature (313 to 333 K),
feed salt concentration (5000 to 7000 mg/l) and permeate pressure
(1.5 to 6 kPa) on the membrane distillation (MD) permeation flux
have been investigated. The maximum flux reached to 28.34 kg/m2 h
at feed temperature, 333 K; vacuum pressure, 1.5 kPa; feed flow rate,
55 l/h and feed salt concentration, 7000 mg/l. The negligible effects
in the reduction of permeate flux found over 150 h experimental run
for salt water. But for the natural ground water application over 75 h,
scale deposits observed on the membrane surface and 29% reduction
in the permeate flux over 75 h. This reduction can be eliminated by
acidification of feed water. Hence, promote the research attention in
apply of VMD for the ground water purification over today-s
conventional RO operation.
Abstract: Abai Kunanbayev is famous for being enlightener,
composer, interpreter, social agent, philosopher, reformer, who
wanted to enrich Kazakh literature by emergence with Russian and
European culture, and also as a founder of Kazakh written literary
language. Abai Kunanbayev was born in 1845 in East Kazakhstan
area and passed away in 1904 in his hometown. His oeuvre absorbed
and reflected all changes in the life of Kazakh society of the second
half of XIX century. Because ХІХ century, especially its second half,
was an important transition period for Kazakhstan, which radically
changed traditional way of Kazakh society and predetermined further
development in consequence of activation of Russian colonial policy
and approval of commodity-money relations in Steppe Land.Abai
Kunanbayev, besides Arabic and Persian common words and
loanwords from Quran in his words of edification, had used a lot of
words of Arabic, Persian, Latin, Russian, Nogai, Shaghatai, Polish,
Greek, Turkish, which are used in the Kazakh language.
Abstract: In response to address different development challenges, Tanzania is striving to achieve its fourth attribute of the National Development Vision, i.e. to have a well educated and learned society by the year 2025. One of the most cost effective methods that can reach a large part of the society in a short time is to integrate ICT in education through e-learning initiatives. However, elearning initiatives are challenged by limited or lack of connectivity to majority of secondary schools, especially those in rural and remote areas. This paper has explores the possibility for rural secondary school to access online e-Learning resources from a centralized e- Learning Management System (e-LMS). The scope of this paper is limited to schools that have computers irrespective of internet connectivity, resulting in two categories schools; those with internet access and those without. Different connectivity configurations have been proposed according to the ICT infrastructure status of the respective schools. However, majority of rural secondary schools in Tanzania have neither computers nor internet connection. Therefore this is a challenge to be addressed for the disadvantaged schools to benefit from e-Learning initiatives.
Abstract: The purpose of this research was develop a biological
nutrient removal (BNR) system which has low energy consumption, sludge production, and land usage. These indicate that BNR system could be a alternative of future wastewater treatment in ubiquitous
city(U-city). Organics and nitrogen compounds could be removed by this system so that secondary or tertiary stages of wastewater treatment satisfy their standards. This system was composed of oxic and anoxic
filter filed with PVDC and POM media. Anoxic/oxic filter system operated under empty bed contact time of 4 hours by increasing
recirculation ratio from 0 to 100 %. The system removals of total nitrogen and COD were 76.3% and 93%, respectively. To be observed
internal behavior in this system SCOD, NH3-N, and NO3-N were
conducted and removal shows range of 25~100%, 59~99%, and
70~100%, respectively.
Abstract: Canola is a specific edible type of rapeseed, developed
in the 1970s, which contains about 40 percent oil. This research was
carried out to determine the yield and some quality characteristics of
some winter canola cultivars during the 2010-2011 vegetation period
in Central Anatolia of Turkey. In this research; Oase, Dante,
Californium, Excalibur, Elvis, ES Hydromel, Licord, Orkan, Vectra,
Nelson, Champlain and NK Petrol winter canola varieties were used
as material. The field experiment was set up in a “Randomized
Complete Block Design” with three replications on 21 September
2010. In this research; seed yield, oil content, protein content, oil
yield and protein yield were examined.
As a result of this research; seed yield, oil content, oil yield and
protein yield (except protein content) were significant differences
between the cultivars. The highest seed yield (6348 kg ha-1) was
obtained from the NK Petrol, while the lowest seed yield (3949 kg
ha-1) was determined from the Champlain cultivar was obtained. The
highest oil content (46.73%) was observed from Oase and the lowest
value was obtained from Vectra (41.87%) cultivar. The highest oil
yield (2950 kg ha-1) was determined from NK Petrol while the least
value (1681 kg ha-1) was determined from Champlain cultivar. The
highest protein yield (1539.3 kg ha-1) was obtained from NK Petrol
and the lowest protein yield (976.5 kg ha-1) was obtained from
Champlain cultivar.
The main purpose of the cultivation of oil crops, to increase the
yield of oil per unit area. According the result of this research, NK
Petrol cultivar which ranks first with regard to both seed yield and oil
yield between cultivars as the most suitable winter canola cultivar of
local conditions.
Abstract: One of the determinants of a firm-s prosperity is the
customers- perceived service quality and satisfaction. While service
quality is wide in scope, and consists of various dimensions, there
may be differences in the relative importance of these dimensions in
affecting customers- overall satisfaction of service quality.
Identifying the relative rank of different dimensions of service quality
is very important in that it can help managers to find out which
service dimensions have a greater effect on customers- overall
satisfaction. Such an insight will consequently lead to more effective
resource allocation which will finally end in higher levels of
customer satisfaction. This issue – despite its criticality- has not
received enough attention so far. Therefore, using a sample of 240
bank customers in Iran, an artificial neural network is developed to
address this gap in the literature. As customers- evaluation of service
quality is a subjective process, artificial neural networks –as a brain
metaphor- may appear to have a potentiality to model such a
complicated process. Proposing a neural network which is able to
predict the customers- overall satisfaction of service quality with a
promising level of accuracy is the first contribution of this study. In
addition, prioritizing the service quality dimensions in affecting
customers- overall satisfaction –by using sensitivity analysis of
neural network- is the second important finding of this paper.
Abstract: Manganese steel (Hadfield) is one of the important
alloys in industry due to its special properties. High work hardening
ability with appropriate toughness and ductility are the properties that
caused this alloy to be used in wear resistance parts and in high
strength condition. Heat treatment is the main process through which
the desired mechanical properties and microstructures are obtained in
Hadfield steel. In this study various heat treatment cycles, differing in
austenising temperature, time and quenching solution are applied. For
this purpose, the same samples of manganese steel was heat treated in
9 different cycles, and then the mechanical properties and
microstructures were investigated. Based on the results of the study,
the optimum heat treatment cycle was obtained.
Abstract: The Brazilian legislation has only established
diagnostic reference levels (DRLs) in terms of Multiple Scan
Average Dose (MSAD) as a quality control parameter for computed
tomography (CT) scanners. Compliance with DRLs can be verified
by measuring the Computed Tomography Kerma Index (Ca,100) with
a pencil ionization chamber or by obtaining the kerma distribution in
CT scans with radiochromic films or rod shape lithium fluoride
termoluminescent dosimeters (TLD-100). TL dosimeters were used
to record kerma profiles and to determine MSAD values of a Bright
Speed model GE CT scanner. Measurements were done with
radiochromic films and TL dosimeters distributed in cylinders
positioned in the center and in four peripheral bores of a standard
polymethylmethacrylate (PMMA) body CT dosimetry phantom.
Irradiations were done using a protocol for adult chest. The
maximum values were found at the midpoint of the longitudinal axis.
The MSAD values obtained with three dosimetric techniques were
compared.
Abstract: An optical fault monitoring in FTTH-PON using ACS
is demonstrated. This device can achieve real-time fault monitoring
for protection feeder fiber. In addition, the ACS can distinguish
optical fiber fault from the transmission services to other customers
in the FTTH-PON. It is essential to use a wavelength different from
the triple-play services operating wavelengths for failure detection.
ACS is using the operating wavelength 1625 nm for monitoring and
failure detection control. Our solution works on a standard local area
network (LAN) using a specially designed hardware interfaced with a
microcontroller integrated Ethernet.